STILLA Windsor Manual de usuario

STILLA

ASSEMBLY INSTRUCTIONS

‘Windsor’4x6

S3008

Every part needed to construct your shed is included inside the pack; cedar

panels, doors, windows, hardware kits & roof sheeting. Please ensure you fully

unpack all the parts & check against the parts checklist before contacting

customer service about anything you believe may be missing. Thank-you!

1 | P a g e

Caution

Please be careful when handling all components, some parts have sharp metal edges.

Always wear work gloves, eye protection and long sleeves when assembling or maintaining

your shed.

Tools required for assembly

•Level

•Drill

•Hammer

•Ladder

•12mm Drill bit

•6mm Drill bit

•Phillips head drive

•Hex Head Drive (5/16’)

•Safety glasses

•Gloves

Before assembly

•Before proceeding with installation, we recommend viewing the Cedar Shed video at

www.stilla.com.au/installation/ or search Stilla Classic Cedar Sheds on Youtube. This doesn’t

show the installation in detail however it could give you some handy tips. Please note we

haven’t videoed the assembly of each shed however the video online is the Maple 12x6 and

will give you an overall idea on how the installation process is completed.

•Remove all parts from packages and place in a safe place close to assembly area.

•Review all instructions; continue to refer to instructions throughout assembly –step

by step.

Preparing your site

•If you are installing your shed on the Stilla rebated floor we recommend finding a

place in your yard that is very close to level. Pavers or a solid material that will not be

affected by weather can be used to perfectly level the shed by placing under the

floor frame where required, make sure all members are supported.

•If you are installing your shed on the Stilla heavy duty floor, this can be placed on

unlevelled surfaces and levelled up by using the 100x100 stumps provided.

2 | P a g e

WINDSOR 4x6 PARTS CHECKLIST

Part Code

Checked

Part Description

Qty

Cedar Clad Panel 900x1895mm

12P

Cedar Clad Panel 1200x1895mm

Cedar Clad Panel 180x1895mm

4x6 Standard Door 830x1875 –Full Cedar

4ft Front Gable

4ft Back Gable

Corner Post 1890x60x18mm

Cover Strip 1890x40x7mm

4ft Fascia Pack (4)

Roof Rafters 580x70x45mm

Door Head 840x35x42mm

Door Step 840x42x19mm

Roof End Piece 203x70x30mm

880mm Sheeting

1200mm Ridge Cap

1060mm Channel

4x6 Hardware Kit

4x6 Instruction Manual

REP

Roof End Plate 1714x70x45mm

Floor Kit –Option

Floor Frame - 140x38mm

Part Code

Checked

Part Description

Qty

End Plate 1800x140x38mm

Double Joist 1208x140x38mm

Single Joist 1208x140x38mm

Logs 750mm

1713mm x 800mm

1713mm x 395mm

Elevation Kit –Option

Must Include a Heavy Duty Floor

Part Code

Checked

Part Description

Qty

Stair Risers (Pair) 1200mm

Stair Treads 240x45x900mm

EKFIX

Fixings - Bolt (With Nut) M12 x 60 Galvanised

Post 100x100 @ 1500mm

3 | P a g e

If no floor option was purchased, go to step 2.0 (Wall Assembly)

SKIP TO BACK FOR IMAGES TO HELP WITH FLOOR INSTALL

STEP 1.0

FLOOR KIT

1.0 –FLOOR KIT

PART CODE

QTY

DESCRIPTION

End Plate 1800mm

Single Joist 1208mm

Double Joist 1208mm

100BS

100mm Batten Screw

1.0 –FLOOR FRAME

Fasten floor frame together as indicated in diagram below, using lines and predrilled holes.

Screw through EP into DJ using 3x 100BS.

Screw through EP into SJ using 2 x 100BS per join.

Ensure frame is square by measuring from corner to corner diagonally, frame will be square

when both diagonal measurements equal the same.

ENSURE 42x35 side of the DJ sits at top.

4 | P a g e

STEP 1.1

FLOOR FRAME INSTALLATION

The 6x6 floor frame comes in one part. Install floor frame in desired position at desired

height and fasten to logs once level and square.

1.1 –FLOOR FRAME INSTALLATION

PART CODE

QTY

DESCRIPTION

Logs 750x100x100mm

100BS

100mm batten screws

200PB

200mm M12 Post Bolt

M12 Washers

1.1 –FLOOR FRAME INSTALLATION

1. Lay out frame in desired position and mark holes to dig, as indicated on diagram

below (use shovel or marking paint).

2. Dig and place logs in holes (using concrete if you wish).

3. Fasten floor frame to logs at desired height, using 4x 100BS per log, ensuring frame is

level*.

* Fasten frame to logs when roughly level and then critique by hammering in or adding dirt

(or concrete) to corners until perfectly level at every post.

Once frame is installed, predrill holes (using a 13mm drill bit) and bolt each log to the floor

frame in spots indicated with 200PB, using washers on both sides.

5 | P a g e

STEP 1.2

FLOOR INSTALLATION

1.2 –FLOORING INSTALLATION

PART CODE

QTY

DESCRIPTION

Floor Board 1713x800mm

Floor Board 1713x395mm

50PS

50mm Philips Screw

1.2–FLOORING INSTALLATION

Fasten floor sheets to floor frame as shown in diagram below using 50PS.

Bring Floor sheets in 43mm on all 4 sides from the outside of the floor frame.

Note- The x marked on the floor sheets do not line up with out joists.

6 | P a g e

STEP 2.0

WALL ASSEMBLY

2.0 - ASSEMBLY PARTS –WALL ASSEMBLY

PART CODE

QTY

DESCRIPTION

Front Wall panel

900mm Wall panel

65HHS

65mm Hex head screw

–If optional window was purchased, it can take the place of any 900mm (9P) panel.

2.0 - ASSEMBLY –WALL ASSEMBLY

Screw through FP into 9P (top, centre & bottom) using 3 x 65HHS. (Holding studs flush on

the outside)

Note: Ensure tongue on VJ cladding is facing upwards.

Screw 3 x

65HHS (Top,

centre &

bottom)

Cedar Strip

When screwing the four corners together please make sure the studs are flush on the

outside (not the inside) as per image below.

7 | P a g e

STEP 2.1

WALL ASSEMBLY

2.1 - ASSEMBLY PARTS –WALL ASSEMBLY

PART CODE

QTY

DESCRIPTION

900mm Wall panel

65HHS

65mm Hex head screw

2.1 - ASSEMBLY –WALL ASSEMBLY

Screw through 9P into 9P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on the

inside.

Screw 3 x 65HHS

(Top, centre &

bottom)

FRONT OF SHED

8 | P a g e

STEP 2.2

WALL ASSEMBLY

2.2 - ASSEMBLY PARTS –WALL ASSEMBLY

PART CODE

QTY

DESCRIPTION

12P

1200mm Wall panel

65HHS

65mm Hex head screw

2.2 - ASSEMBLY –WALL ASSEMBLY

Screw through 12P into 9P (Top, centre & bottom) using 3 x 65HHS, holding studs flush on

the outside.

12P

Screw 3 x

65HHS (Top,

centre &

bottom)

FRONT OF SHED

9 | P a g e

STEP 2.3

WALL ASSEMBLY

2.3 - ASSEMBLY PARTS –WALL ASSEMBLY

PART CODE

QTY

DESCRIPTION

900mm Wall panel

65HHS

65mm Hex head screw

2.3 - ASSEMBLY –WALL ASSEMBLY

Screw through 12P into 9P (top, centre & bottom) using 3 x 65HHS holding studs flush on

the outside.

Screw 3 x 65HHS

(Top, centre &

bottom)

12P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento al aire libre de STILLA

STILLA

STILLA Birch 6x3 Manual de usuario

STILLA

STILLA PADDINGTON Manual de usuario

STILLA

STILLA ASCOT Manual de usuario

STILLA

STILLA Palmwood Manual de usuario

STILLA

STILLA Maple Manual de usuario

STILLA

STILLA Peppertree 9x6 Manual de usuario

STILLA

STILLA Acacia Manual de usuario

STILLA

STILLA S3105 Manual de usuario

Manuales populares de Almacenamiento al aire libre de otras marcas

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manual de usuario

TYGO

TYGO Nyland Manual de usuario

Duratuf

Duratuf GL105 Manual de usuario

Viking

Viking SD5300SS Manual técnico

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manual de usuario

ModuLaro

ModuLaro Lojo WC202200 Manual de usuario

Lifetime

Lifetime 6418 Manual de usuario

rollaway container

rollaway container ARPCA24 Manual de usuario

Duratuf

Duratuf Havelock Manual de usuario

X-METAL

X-METAL 4065 Manual de usuario

Outdoor Life Products

Outdoor Life Products FP2030 F Manual de usuario

Royalcraft

Royalcraft Faro 295L Storage Box Manual de usuario

Riverlea

Riverlea Duratuf KIWI KS3 Manual de usuario

OLT

OLT GS84D-FJ-Plywood Manual de usuario

Rubbermaid

Rubbermaid 5L45 Manual de usuario

garofalo

garofalo TUSCANY EVO Manual de usuario

Duratuf

Duratuf Kiwi MK1 Manual de usuario

Eden

Eden CA2988 Manual de usuario