Stiga PARK 121 M Manual de usuario

STIGA PARK

121 M

8211-3011-09

1. Park -1993

2. Park -1993

3. Park -1993

4. Park -1993

5a.

6a. Park -1999

6b. Park 2000-

5b.

Denna produkt, eller delar därav, omfattas av följande

mönsterskydd:

This product, or part of it, is covered by the following

design registration:

Sverige/Sweden 62 435

Tyskland/Germany M97 07 997.9 (pending)

9. 13.

14.

10.

11. 15.

12.

ENGLISH GB

SYMBOLS

The following symbols can be found on the

machine to remind you of the care and attention

that are required during use.

The symbols mean:

Warning!

Read the instruction manual and the safety

manual before using the machine.

Warning!

Do not insert your hands or feet under the

cover when the machine is in operation.

Warning!

Watch out for discarded objects. Keep

onlookers away.

Warning!

Before starting repair work, remove the

spark plug cable from the spark plug.

INTRODUCTION

ThiscuttingdeckmayonlybeusedwithPark

machines with a motor performance of at least 16

hp.

The cutting deck is available as standard in two

versions:

- with mechanical setting of the cutting height

(item no. 13-2915).

- with factory-fitted, electrical setting

of the cutting height (item no. 13-2921).

PREPARATIONS

Park, year models up to and including 1993:

In order for the deck to be used, the machine has to

be modified:

1. Remove the return spring for the articulated

joint

(fig. 1).

2. Saw off the spring mount flush with the frame

side member

(fig. 2).

3. Drill a new hole (Ø 8 mm), 8 mm from the lower

edge of the frame side member (fig. 3).

4. Install the spring in the new hole (fig. 4).

INSTALLATION

CUTTING DECK

1. Screw the cutting deck into the deck mounts D

(fig. 5a).

2. Attach the lift spring to the implement lifter (fig.

5b).

3. Install the lifting cylinder in the front lifting arm

by inserting the accompanying spacer in the hole

on the lifting cylinder and threading on two

washers, one on either side. Secure with screw and

nut (only applies to item no. 13-2921).

4. Connect the electrical contact to the socket on

the side of the machine (only applies to item no.

13-2921), (fig. 6).

V-BELT

1. Set the cutting height setting to an intermediate

position.

2. Force the V-belt onto the machine’s centre

pulley F (fig. 7).

3. Tension the belt with belt idler G. The belt idler

should be on the left of the belt viewed from the

driver’s position.

4. Park -1999:

Hook the belt idler spring H in the floor on the

right side (fig. 7).

SETTING

In order for the deck to cut evenly and attractively,

it has to be correctly adjusted:

1. Make sure the air pressure in the tyres is correct:

Front: 0.6 bar (9 psi).

Rear: 0.4 bar (6 psi).

2. Place the machine on a level floor. Undo screws

I (fig. 8).

3. Adjust the deck so that the front and rear edge of

the cover are the same height above the floor.

4. Tighten the screws.

ENGLISH

USE

CUTTING HEIGHT

The cutting height can be varied from 30 to 80 mm.

- item no. 13-2915 has seventeen fixed positions

for cutting height.

- item no. 13-2921 has continuously variable

adjustment of cutting height.

Note: Stated cutting heights apply when the

machine is on a firm surface.

CUTTING TIPS

For optimum ‘Multiclip effect’, follow these tips:

- cut frequently.

- run the motor at full revs.

- keep the underside of the cutting deck clean.

- use sharp blades.

- do not cut wet grass.

- cut twice (with different cutting heights) if

the grass is long.

MAINTENANCE

PREPARATIONS

Unless otherwise stated, all service and

maintenance must be carried out on a stationary

machine when the motor is not running.

Prevent the machine from rolling by

always applying the parking brake.

Prevent unintentional starting of the

motor by always stopping the motor,

disconnecting the spark plug cable

from the spark plug and earthing it.

Disconnect the negative cable from the

battery.

MAINTENANCE TIPS

To make cleaning and maintenance easier, the

cutting deck can be folded up:

1. Set the cutting height setting to an intermediate

position (= drive belt minimum tension).

2. Secure the tensioning arm on the hook.

3. Force the belt off the centre pulley F.

4. Undo both pins J (fig. 9).

5. Grip the deck’s frame (fig. 10).

6. Fold up the deck until it is upright on the rear

support plates (fig. 11).

CLEANING

After each use, the underside of the cutting deck

should be rinsed off.

If the grass has dried solid, scrape clean the

underside.

If necessary, paint the underside to prevent

corrosion.

POSITIVE DRIVE BELTS

If one of the blades has struck a solid object (e.g. a

stone), the belt tension may be altered. This can

lead to the positive drive belt ‘over-meshing’

which, in the long term, can damage the blades.

Adjust the belt tension if necessary:

1. Secure the tensioning arm on the hook.

2. Force the belt off the centre pulley F.

3. Dismantle the transmission cover.

4. Undo tensioning arm K (fig. 12).

5. Undo the bearing box’s mounting screws L (fig.

13).

6. Tension the positive drive belt by pressing the

tensioning arm backwards.

7. Tighten the tensioning arm’s mounting screw.

8. Tighten the bearing box’s mounting screws.

9. Repeat with the other positive drive belt.

When replacing positive drive belts,

ensure that both the outer blades are

always at right-angles to the central

blade(seefig.14).

If the positive drive belts are incorrectly mounted,

the blades will strike each other because they

overlap.

Always check the position of the blades after

replacing a belt or adjusting belt tension.

REPLACING BLADES

Use protective gloves when changing

blades to avoid cutting yourself.

Ensure that the blades are always sharp. This

produces the best cutting results.

ENGLISH GB

Always check the blades after a collision. If the

blade system has been damaged, defective parts

should be replaced.

Always use original spare parts. Non-

original spare parts can entail a risk of

injury, even if they fit the machine.

The cutting system comprises three blade

bars with two replaceable blades Y (fig. 15). When

replacing blades, both should be replaced to avoid

imbalance.

Install the new blades. Tighten screws V and W

properly. Tightening torque: V - 9.8 Nm, W - 24

Nm.

In the event ofa powerful collision, the blades may

be bent out. Undo the locking nut X and fold back

the blade. Install a new original break bolt V.

Tighten the locking nuts X and Z.

SPARE PARTS

STIGA original spare parts and accessories are

designed specifically for STIGA machines. Please

note that ‘non-original’ spare parts and accessories

have not been checked or approved by STIGA:

The use of such parts and accessories

can affect the function and safety of the

machine. STIGA accepts no

responsibility for damage or injuries

caused by such products.

STIGA reserves the right to make alterations to the

product without prior notification.

MOWING AHEAD

BOX 1006 · SE-573 28 TRANÅS

www.stiga.com

Otros manuales para PARK 121 M

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortacésped de Stiga

Stiga

Stiga SWP 335 Manual de usuario

Stiga

Stiga MULTICLIP 8211-0203-09 Manual de usuario

Stiga

Stiga MCS 474 Series Manual de usuario

Stiga

Stiga VILLA 107M Manual de usuario

Stiga

Stiga ESTATE SENATOR Manual de usuario

Stiga

Stiga PARK COMPACT Manual de usuario

Stiga

Stiga DECK PARK 121 M - 4WD Manual de usuario

Stiga

Stiga XM 130 Manual de usuario

Stiga

Stiga EXPERIENCE Estate 798e Manual de usuario

Stiga

Stiga CP1 430 Li 48 series Manual de usuario

Stiga

Stiga R72 Li 48 V1 Manual de usuario

Stiga

Stiga PARK 121 M Manual de usuario

Stiga

Stiga MCS 474 Series Manual de usuario

Stiga

Stiga NT 484 series Manual de usuario

Stiga

Stiga EL 380 Manual de usuario

Stiga

Stiga TORNADO 51 S Manual de usuario

Stiga

Stiga MJ 66 Instrucciones de operación

Stiga

Stiga COLLECTOR 45 COMBI EL Manual de usuario

Stiga

Stiga TH 122 Series Manual de usuario

Stiga

Stiga DECK PARK 121 M - 4WD Manual de usuario

Stiga

Stiga PARK UNLIMITED Manual de usuario

Stiga

Stiga Park series Manual de usuario

Stiga

Stiga 2021 Edition PARK 320 P Manual de instrucciones

Stiga

Stiga Garden Compact Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario