Stiga 85 M Manual de usuario

DEUTSCH D

8211-3502-01

85 M

1. 5.

3. 7.

4. 8.

11.

9. 10.

Denna produkt, eller delar därav, omfattas av följande

mönsterskydd:

This product, or part of it, is covered by the following

design registration:

Sverige/Sweden 62 435

ENGLISH

SYMBOLS

The following symbols are displayed on the ma-

chine in order to remind you about the safety pre-

cautions and attention necessary when using the

machine.

The symbols mean:

Warning!

Read the instruction book and safety man-

ual before using the machine.

Warning!

Do not put hands or feet under the cover of

the machine when it is running.

Warning!

Beware of objects being flung out. Keep

spectators away.

Warning!

Beforestartinganyrepairwork,removethe

spark plug cable from the spark plug.

INTRODUCTION

The power outlet's tension roller and tension arm's

spring on the base machine are available in two ver-

sions (figs 1 and 2).

NOTE! To be able to fit this mower deck ("Multi-

clip" mod. 85M) version B is required.

VERSION A:

(Standard on models made between 1982 - 83).

If the base machine is fitted with version A a sepa-

rate assembly set is required to be able to fit the

mower deck.

Assembly set, art. No.: 13-1967-11.

The set contains a v-belt, tension roller, spring, as-

sembly components and assembly instructions.

N.B. Older base machines can, however, be fitted

with version B if they have previously been adapted

for use with a "Multiclip" mower deck.

VERSION B:

(Standard on machines made from 1994 - ).

The mower deck can be fitted directly.

ASSEMBLY

MOWER DECK

1. Remove both mounting bolts D on the base ma-

chine (fig 3).

2. Insert both spacer sleeves E in the mower deck's

arms (fig 4). The spacer sleeves are supplied in a

plastic bag.

3. Bolt the mower deck to the base machine.

4. Pull the v-belt onto the mower deck's pulley.

(This is carried out easier if the height adjustment

lever is in position "5").

5. Make sure that the tension roller J is on the out-

side of the v-belt (figs 2 and 5).

6. Hook the spring into the bracket G (figs 2 and 5).

7. Screw the guard H in position using three screws

(fig 6). The screws are supplied in the plastic bag.

8. Hook the chain I and lifting spring F in the attach-

ment's lift arm (fig 6).

SETTING

For the mower deck to mow evenly and cleanly it

needs to be adjusted correctly:

1. Make sure the tyre pressure is correct:

Front: 0.4 bar (6 psi).

Rear: 1.2 bar (17 psi).

2. Place the machine on a flat surface. Loosen the

screws K (fig 7).

3. Adjust the mower deck so that the casing's front

and rear edges are the same height from the floor.

4. Tighten the screws.

USE

MOWING HEIGHT

Themowerdeckhas17fixedmowingheights,from

30 mm to 80 mm.

N.B. The stated mowing heights apply when the

machine is standing on firm ground.

MOWING ADVICE

For the best "Multiclip" effect follow this advice:

- mow regularly.

- use full throttle on the engine.

ENGLISH GB

- keep the underside of the mower deck clean.

- use sharp blades.

- do not mow wet grass.

- mow twice (using different mowing heights)

if the grass is long.

MAINTENANCE

Noserviceactionmustbetakenonthe

mower deck unless:

- the engine has been stopped.

- the ignition key has been removed.

- the spark plug cap has been removed

from the spark plug.

- the parking brake is engaged.

- the mower deck is disengaged.

CLEANING

After use, rinse off the underside of the mower

deck using a garden hose.

If grass cuttings have dried on to the attachment,

dismantle the mower deck and scrape clean the un-

derside.

If necessary touch-up the underside using a suita-

ble paint to prevent corrosion.

CHANGING THE DRIVE BELT

1. Remove the mower deck from the base machine.

2. Remove the transmission casing.

3. Loosen the tension arm L (fig 8).

4. Loosen the right hand bearing box's fixing bolts

M (fig 9).

5. Fit the new drive belt.

Thenewdrivebeltmustbefittedsothat

the blades are square (90°) to each oth-

er. See figure 10. If you fit the drive belt

incorrectly the blades will hit each oth-

er resulting in the blades being dam-

aged.

6. The belt is tensioned by pushing the tension arm

L forwards and then securing in position.

7. Tighten the bearing box's fixing bolts M.

When the drive belt is fitted, check, by

turningthemowerdeckoverandturn-

ing the blades, that it has been fitted

correctly. NOTE! The mower deck

should be dismantled from the base ma-

chine.

8. Now refit the mower deck on the base machine.

CHANGING BLADES

Use protective gloves to prevent cuts

when changing blades/blade tips.

Make sure the blades are always sharp. This gives

the best mowing results.

Always check the blade(s) after an impact. If the

blade system has been damaged the defective parts

must be changed.

Always use original spare parts. Using

non-original spare parts can result in

the risk of damage even if they fit in the

machine.

The cutting system consists oftwo blade bars, each

with two interchangeable blade tips Y (fig 11).

Both blade tips should be replaced at the same time

to avoid any imbalance.

Fit the new blade tips. Tighten the screws V and W

fully. Tightening torque: V - 9.8 Nm, W - 24 Nm.

And heavy impact can result in the blade tip being

folded aside. Loosen the locking nut X and turn the

blade tip back to its correct position. Mount a new

shear bolt V. Tighten the lock nuts X and Z.

Otros manuales para 85 M

Tabla de contenidos

Otros manuales de Cortacésped de Stiga

Stiga

Stiga MP 84 Series Instrucciones de funcionamiento e instalación

Stiga

Stiga MP 84 Series Manual de usuario

Stiga

Stiga MULTICLIP 50 EL SVAN Manual de usuario

Stiga

Stiga ESTATE PRO 25 13-2563-13 Manual de usuario

Stiga

Stiga EURO 33 ELECTRIC 33 Manual de usuario

Stiga

Stiga MP2 500 Li D48 Series Manual de usuario

Stiga

Stiga EL 340 Li 48 Manual de usuario

Stiga

Stiga MULTICLIP 46 ELECTRIC Manual de usuario

Stiga

Stiga COMBI 748 S Manual de usuario

Stiga

Stiga EXPERIENCE e-Ride C500 Manual de usuario

Stiga

Stiga EL 340 Manual de usuario

Stiga

Stiga CP1 430 Li 48 series Manual de usuario

Stiga

Stiga SCM 240 R Manual de usuario

Stiga

Stiga MULTICLIP 51S Manual de usuario

Stiga

Stiga EL 340 Manual de usuario

Stiga

Stiga MPST 84 Li 48 V1 Manual de usuario

Stiga

Stiga MP 98 Series Manual de usuario

Stiga

Stiga Cruiser CR 430 Li 80 Series Manual de usuario

Stiga

Stiga EL 340 Li 48L Manual de usuario

Stiga

Stiga PARK COMPACT 16 4WD Manual de usuario

Stiga

Stiga DECK PARK 121 M - 4WD Manual de usuario

Stiga

Stiga CP1 530 Li D48 series Manual de usuario

Stiga

Stiga Park series Manual de usuario

Stiga

Stiga Park 340 PX Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario