Stevens Aero Model SQuiRT Manual de usuario

SQuiRT

A Speed 400 Primary Trainer

V1.04WAA

Span 38” / Length 26” / Area 260Sq.” / Weight 14.0-16.0oz

WARRANTY

Stevens AeroModel guarantees this kit to be free from defects in both material and workmanship

at the date of purchase. This warranty does not cover any component parts damaged by use or

modification. In no case shall Stevens AeroModel’s liability exceed the original cost of the

purchased kit. Further, Stevens AeroModel reserves the right to change or modify this warranty

without notice.

In that Stevens AeroModel has no control over the final assembly or material used for final

assembly, no liability shall be assumed nor accepted for any damage resulting from the use by

the user of the final user-assembled product. By the act of using the user–assembled product,

the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer

is advised to return this kit immediately in new and unused condition to the place of purchase.

REQUIRED TO COMPLETE KIT:

Kit Contents:

1. Rolled Computer Drawn Plan Sheet

2. Illustrated Instruction Manual

3. Laser Cut Balsa and Hardwood Parts Sheets (See Cut Parts Inventory Sheet)

4. 2 - 1/8” x 24” Hardwood Dowel. (taped to back of wood brick)

5. Pre-Formed .093” dia. spring steel landing gear. (taped to back of wood brick)

6. Vinyl windscreen and wing stripe decal set.

7. Hardware Bag

•3 - 1/8” x 3” hardwood dowels

•1 -3/16” x 3” hardwood dowel

•1 - #16 Rubber Bands

•2 - .045” x 11” Push Rods (Z-Bend)

•1 - .032” x 11” Music Wire

•1 - .032” ID x 11” Nylon Tube

•1 - Pair 2” Foam Wheels (GW/LFW-508/21) [Builder must drill hubs to fit 3/32” wire gear]

•1 - ½” Sullivan #60 Tail Wheel

•1 - Du-Bro 919 (BULK 27800) Micro2 Control Horns (2/Pkg.) [Builder must drill to fit .045” Push Rods]

•1 - Du-Bro 845 Mini EZ Connector (2/Pkg.)

•2 - Rubber wheel collars (GW/AD001 2.3mm)

•2 - 3/16” Diameter Neo. Magnets

Recommended Finishing Items:

1. One roll of AeroLITE or AeroFILM covering available from www.stevensaero.com

Suggested Electronics:

1. Your squirt will operate well on a 3-4 Channel Transmitter.

2. 2 - Hitec HS-55 Servos (use of HS-55 servos will negate the need for two 6” servo extensions)

3. 2 - 6” Servo Extension (Only required if you do not use the suggested HS-55 Servos)

4. 1 - Micro Receiver 3-4 Channel (Castle Creations Berg MS4L or similar recommended)

5. 1 - 10-20A ESC we suggest GWS ESC300A or Castle Creations Pixie 20p

6. 1 - GWS EDP-400 or 6v Speed 400 Motor

7. 1 - GWS EMM-400A Motor Mount

8. 1 - GWS DS002 or 2.3mm Prop Shaft Adapter

9. 1 - GWS 7x3.5 HD Prop

10. 1 - GWS ½” Spinner

11. 1 - 2 Cell 7.4V LiPo Battery we suggest Apogee 1000mah (20C) or ThunderPower 1320 (13C)

Brushless Motor Upgrades: While not necessary for proper flight performance, we understand that there many will

choose to upgrade the SQuiRT to a brushless power system. The Align 430L 2250KV series motor will fit without

modification to the EMM-400A Motor Mount and is an excellent performer on 7.4V batteries. Additionally a GWS

gearbox may be fitted to the airframe using the supplied motor stick assembly opening up many good options. With

many of the lighter brushless motors it may become necessary to relocate your servos forward into the servo tray

within the radio box area of the fuselage.

Items You May Need:

1. Thin, Medium, and Thick CA (super glue) or White Glue

2. Plan/Table Protector (use the bag that this kit came in to protect your work surface from CA glue spills)

3. Razor Blade(s)

4. Med-Fine Grit Sand Paper and sanding block

5. Clear Tape

6. Balsa Wood Filler

7. .047” and .093” drills.

GENERAL ASSEMBLY INSTRUCTIONS:

Thank you, for purchasing this Stevens Aeromodel SQuiRT – A speed 400 primary trainer. This kit provides the builder

and pilot a refreshing change of pace from heavy “ARF” style plywood box airframe construction and blends stick and

tissue design methods of the past with state of the art CAD technology and precision interlocking laser cut parts; the result

is something you will find truly exceptional to build and fly. This kit is intended for a beginner-novice builder and beginner

pilot as a primary 3-channel trainer.

Best Regards,

Bill Stevens

[email protected]

Stevens AeroModel “Laser Engineered Kits™”

1528 S. Nevada Ave.

Colorado Springs, CO 80906

Assembly Tips

READ THE INSTRUCTIONS and the plan sheet prior to starting any work!

Tape plans to work table. Cover with wax paper or plastic wrap.

Join all joints with Thin CA unless otherwise specified.

DO NOT REMOVE THE PARTS FROM THE BALSA SHEETS UNTIL REQUIRED!

DO NOT FORCE THE FIT – when in doubt double check your parts - removal of material should not be

required. If you feel that you have a poor connection check first to see that the part is not upside down.

Reference each piece against the plan sheet.

Making solid glue joints: Hold parts together on top of plan sheet using moderate pressure to fit parts - wick thin

CA into joint. (There is no need to pin parts to work table as all pieces interlock and self - jig.)

Fuselage Assembly

Lets begin construction by assembling the fuselage core. Locate the following 1/8” Lite Plywood parts marked

F2, F3a, and F3b. Locate the 3/32” balsa part F4. Dry fit (no glue) the assembly together as indicated in the

photo below. Please note that F1 and F2 have forward designations these parts are etched with the word

“FRONT” do make certain to assemble these parts with “FRONT” facing the nose of the model. Tip! If a part

does not fit properly check the forward orientation.

Locate the 1/8” Lite Plywood part F1 and dry fit to the core as indicated in the photo below. Make certain that

the entire assembly fits together without any gaps check for square then glue parts together by wicking thin CA

glue into adjoining surfaces.

Invert the core assembly and add the 1/16” plywood motor mount doublers to the inside of the core assembly as

pictured below.

Next, install the 1/8” Lite Plywood Parts L1 and L2 to the underside of the core as indicated in the following

photo.

Locate the 3/32” balsa fuselage sides and the 3/32” balsa former F5. Dry fit former F5 to the rear of the core

assembly and the fuselage sides as indicated in the photo below. Once satisfied with the fit, glue the fuselage

side to the core assembly. Repeat for the opposite side. Tip! you must fit F5 to the core prior to joining the

fuselage sides.

Now install the F7 cabin cross grain doublers they can be found on the 3/32” balsa sheet. These parts key

inside the fuselage as indicated in the photo below.

Locate the 1/16” balsa part F8 and install to the front of the cabin spanning the fuselage sides and F7 as

indicated in the photo below. Tip! F7 is recessed to receive F8 align the top of F8 with the upper recess in F7.

Now locate the 1/16” balsa part F9 and the 3/32” balsa part F6. Dry fit F9 to the top of the fuselage, next fit the

former F6 to the fuselage and part F9. Invert the fuselage on your work surface, square, and retain parts with

thin CA glue.

Locate the 1/16” Plywood servo tray and glue inside the fuselage as indicated in the photos below.

Next, fit the 3/32” balsa part F10 to the aft end of the fuselage as indicated in the photo below.

Invert the fuselage and fit the lower 1/16” balsa decking part F11 as indicated in the photo below.

Locate the 3/32” balsa parts F12 and key within the underside of the fuselage as indicated in the photo below.

F12 doubles the fuselage battery access hatch and is shaped along it’s leading edge to fit snug against the

inside plywood structure. Tip! Make certain that F12 rests upon the F11 decking installed in the step prior.

Assemble the battery access hatch catch/cross brace from 1/16” balsa parts C1, C2, and C3 as indicated in the

photos below. With the catch/brace assembled install one 3/16” rare earth magnet in the circular cutout –

secure the magnet with thin CA glue.

Install the completed cross brace to the fuselage as indicated in the photo below. The leading edge of the

catch/brace should be flush with the leading edge of the deck part F11. Tip! Sand lightly if the fit is too snug (a

result of the C1,2,3 parts not being aligned properly when gluing) – don’t force the parts to fit.

Assemble the battery hatch from the 1/16” balsa parts H1 and H2. Note that H1 is etched with the outside

shape of H2 to aide in aligning the parts. With H1 and H2 assembled as indicated in the first photo move on to

installing the magnetic catch magnet and forward catch(1/16” balsa part H3). Tip! make certain you install your

magnet in the hole that matches the magnet installed within the fuselage assembly.

Now locate the F13 and F14 balsa sheeting and sheet the nose of the aircraft starting from the leading edge of

L2 following the recess between created by the inner plywood core and the fuselage sides as indicated in the

photos below.

You’ll notice that the upper deck slightly overhangs the front of the windshield. Using a medium grit sand paper

and your sanding block sand off the overhang as indicated in the photos below.

Otros manuales para SQuiRT

Tabla de contenidos

Otros manuales de Juguete de Stevens Aero Model

Stevens Aero Model

Stevens Aero Model rockette 100 Manual

Stevens Aero Model

Stevens Aero Model FreDe 2X Manual

Stevens Aero Model

Stevens Aero Model Scimon 20 Manual

Stevens Aero Model

Stevens Aero Model FREDe 1.5X Manual de usuario

Stevens Aero Model

Stevens Aero Model Stella Manual de usuario

Stevens Aero Model

Stevens Aero Model CAP 232 Manual de usuario

Stevens Aero Model

Stevens Aero Model QuickOats 250 Manual

Stevens Aero Model

Stevens Aero Model microHawk Manual de usuario

Stevens Aero Model

Stevens Aero Model Ace 100 Manual de usuario

Stevens Aero Model

Stevens Aero Model microMAX 103 Manual

Stevens Aero Model

Stevens Aero Model Clipped-Wing Taylorcraft Manual

Stevens Aero Model

Stevens Aero Model Swift 100 Manual del propietario

Stevens Aero Model

Stevens Aero Model S-Pou! 300 Manual

Stevens Aero Model

Stevens Aero Model RV-4 Manual de usuario

Stevens Aero Model

Stevens Aero Model BuzzBomb 400 Manual

Stevens Aero Model

Stevens Aero Model Build It! RingRat 250 Manual de usuario

Stevens Aero Model

Stevens Aero Model Say's Nuh! C-140 Manual

Stevens Aero Model

Stevens Aero Model PuddleBug 2.4 Manual de usuario

Stevens Aero Model

Stevens Aero Model PLAYMITE 75 Manual

Stevens Aero Model

Stevens Aero Model SkyBuggy 100 Manual

Stevens Aero Model

Stevens Aero Model QuickOats 100 Manual del propietario

Stevens Aero Model

Stevens Aero Model Sky Scout Floats Manual de usuario

Stevens Aero Model

Stevens Aero Model Hummingbird (100) Manual

Stevens Aero Model

Stevens Aero Model SHAFT25e Manual de usuario

Manuales populares de Juguete de otras marcas

marklin

marklin 37321 Manual de usuario

Canon

Canon PAPER CRAFT Manual de usuario

GREAT PLANES

GREAT PLANES Pitts M-12S Manual de usuario

NOCH

NOCH 14261 Manual de usuario

Hausler

Hausler 450 SE V2 Manual de usuario

Dynaflite

Dynaflite Daydream Manual de usuario

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manual

Kenner

Kenner Batman 63651 Manual de usuario

LEGO

LEGO 8527 Manual de usuario

iKarus

iKarus ECO 8 Manual de usuario

Multiplex

Multiplex EasyStar II Manual de instrucciones

Walkera

Walkera 38 Manual de instrucciones

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manual de usuario

MD MXION SWD Manual de usuario

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manual de usuario

marklin

marklin 39671 Manual de usuario

Meccano

Meccano 15103 Manual de usuario

LEGO

LEGO TECHNIC 8735 Manual de usuario