Steris Amsco 600 ALUS Manual de usuario

steris.com

Mentor, OH 44060 |USA

©2022 STERIS. All Rights Reserved. M12570EN.2122-09,Rev A

AMSCO® 600 ALUS

Automatic Load and Unload System (ALUS)

1

QUICK REFERENCE GUIDE

Attaching a ﬁxed or variable height transfer carriage to the ALUS Table,

Sterilizer, or Pass-Through Loading Cart Return Chamber

To avoid damage to the ALUS table end bracket and front panels,

ensure locking lever is turned to the left, green label side.

2If using a Variable Height Transfer Carriage, adjust height of Transfer Carriage

using preset memory buttons.

3Approach sterilizer straight on, NOT at an angle, aligning notch on Loading Car

with arrow above sterilizer door.

4

Turn locking lever to the right, (red label side), and pull back on

Transfer Carriage handles to ensure it is properly engaged and

locked to Sterilizer, ALUS table or Pass-Through.

Before unloading the Loading Car, visually verify Transfer Carriage

is properly attached. Do not attach Transfer Carriage to sterilizer

front panel or pass-through front panel gap.

Resetting the ALUS table After “Failure to Unload” Alarm

1Turn manual operation key to the right, wait 15 seconds.

2Turn manual operation key to the left, wait 15 seconds.

5Engage locks on Transfer Carriage rear casters and unload Loading Car.

6Turn locking lever back to the left, green label side to undock Transfer Carriage.

Some labels may be black instead of green and red

steris.com

Mentor, OH 44060 |USA

©2022 STERIS. All Rights Reserved. M12570EN.2122-09,Rev A

AMSCO® 600

Variable Height Transfer Carriage

1

QUICK REFERENCE GUIDE

Setting the Optional Variable Height Transfer Carriage Memory Buttons

Set Transfer Carriage to appropriate height

using UP/DOWN arrows.

2Simultaneously press both SET buttons

and “M1” (Memory) button.

3

The M2 and M3 buttons can also be

set to accommodate different sterilizer,

pass through hatch or Auto Load/Unload

System heights.

4

To operate, continually press the

appropriate memory button until the

programmed height is reached (Transfer

Carriage movement will stop).

1

Resetting the variable height transfer carriage.

If battery level is too low, Variable Height Transfer Carriage will enter sleep mode and

requires a battery charge and reset to begin functioning again.

Charge Transfer Carriage batteries daily to extend battery life, avoid loss of memory

settings and need to reset Transfer Carriage.

Press UP and DOWN buttons on Transfer Carriage control pad simultaneously. There

will be 10 long beeps followed by a series of short beeps.

Release buttons after 10 long beeps and proceed to Step 2.

2Press DOWN button until Transfer Carriage trolley reaches bottom position (height-

adjustment speed will be slower than normal).

3When Transfer Carriage is in DOWN position, actuators will RESET and Transfer

Carriage can be used again.

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Steris

Steris

Steris V-PRO 60 Manual de usuario

Steris

Steris Reliance EPS Endoscope Processing System Manual de usuario

Steris

Steris AMSCO 1215 Manual de usuario

Steris

Steris Basil 3500 Manual de usuario

Steris

Steris SYSTEM 1 endo Manual de usuario

Steris

Steris VHP MD140X Manual de usuario

Steris

Steris VHP X10 Manual de usuario

Steris

Steris AMSCO 600 Medium 639V-3 Manual de usuario

Steris

Steris Basil 1100 Manual de usuario

Steris

Steris V-PRO maX 2 Manual de usuario

Steris

Steris SYSTEM 1 endo Manual de usuario

Steris

Steris Reliance 1024 Manual de usuario

Steris

Steris AMSCO 400 Series Manual de usuario

Steris

Steris Basil 9502 Manual de usuario

Steris

Steris AMSCO 30 Series Manual de usuario

Steris

Steris Basil 4700 Manual de usuario

Steris

Steris SYSTEM 1E Manual de usuario

Steris

Steris Basil 6000 Manual de usuario

Steris

Steris Reliance 5000 Series Manual de usuario

Steris

Steris AMSCO 2532 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario