Steren K-420 Manual de usuario
ENGLISH
ENGLISH-02
Before using your new analog/digital converter kit, please make
sure to read this instruction manual in order to avoid any
malfunctions or misuse. Please keep this manual for future
reference.
IMPORTANT
A parallel port interface K-400 is required for the programming of
this kit.
Do not expose this device to direct sunlight or to extreme
temperatures.
Do not use or store the kit anywhere it might get wet as this could
cause a malfunction.
This device contains small parts. Do not leave it within the reach of
children.
Adult supervision is recommended when the device is being
assembled because it requires soldering.
Always use a soft dry cloth in order to clean.
You must have circuit soldering skills to avoid damages in the
printed circuit.
Use a 30W soldering pen.
•
•
•
•
•
•
•
•
ENGLISH
ENGLISH-03
FEATURES
FEATURES
This analog/digital converter kit is ideal for electronic students or
hobbyists because it allows them to develop creativity in the
programming of this prototype of a mechanical system.
This kit includes all the components necessary for building this
prototype.
Your new analog/digital converter kit allows you to program different
functions and applications for an 8 bit A/D converter.
In the “Manual ABC de la Mecatrónica” you will nd different examples
the programming and reading of the A/D and basic digital oscilloscope
development.
REQUIRED EQUIPMENT
Soldering Iron.
Soldering Solution.
Regulated 5 volts power source.
•
•
•
ENGLISH
ENGLISH-04
CONTAINED WITHIN
1 Printed Circuit PCB 1 Resistance R10K
1 DB-9 Connector (500-020) 1 Integrated Circuit CMOS ADC0804
1 Condensator 150pF C-150-500
In order to install the integrated circuits, observe the safety
precautions and pay special attention to the numbering of the pins
locating the #1 pin.
PIN 1
ENGLISH
ENGLISH-05
INSTALLATION
Before beginning the assembly of this kit, it is necessary to have a
pencil type soldering iron and soldering solution. Adult supervision is
recommended during assembly.
1.- Place the resistance in its respective position (R1). Solder the
terminals on their underside and cut off the excess metal
2.- Place the integrated circuit in its respective position (U1). Check
the pin position and solder the terminals on their underside and cut off
the excess metal.
3.- Place the DB9 connectors in their respective positions (J1). Solder
the terminals on their underside and cut off the excess metal.
4.- Place the condensator in its respective positions (C1). Solder the
terminals on their underside and cut off the excess metal
5.- Solder the power cables in their respective positions (BT1). The
power input voltage is 5 volts.
6.- Solder the signal cable in its respective position (Vin). The
maximum input voltage is 5 volts.
OPERATION OF THE ANALOG/DIGITAL CONVERTER KIT
K-420
1. Never connect the analog/digital converter kit K-420 to the
computer if the analog/digital converter kit is connected to the power
source.
2. Make sure the analog/digital converter kit K-420 is powered off.
3. Once the analog/digital converter kit K-420 is connected, make sure
its supported by a non-conducive surface and that this surface is free of
any elements that may cause a short circuit in the PCB circuit.
4. Make sure that the power cables are well connected and that the
power source is correct at 5 regulated volts.
SPECIFICATIONS
Polarization Voltage: 5 V - - -
Power Consumption: 3 mA
Product design and specications are subject to change without
previous notice.
DIAGRAM
ENGLISH
ENGLISH-06
DIAGRAM
ENGLISH
ENGLISH-07
WARRANTY
This Steren product is warranted under normal usage against defects in workmanship and
materials to the original purchaser for one year from the date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase ticket, product
box or package, and product, must be presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accessories to customer, as well as
warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries,
failure to follow enclosed instructions, improper repair by unauthorized personnel, improper
safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
Product: Analog / Digital Converter Kit
Part number: K-420
Brand: Steren
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your nearest dealer. If
you are in Mexico, please give a call to our Call Center.
Call Center
01 800 500 9000
Tabla de contenidos
Idiomas:
Otros manuales de Convertidor de medios de Steren
Steren
Steren ELI-120 Manual de usuario
Steren
Steren 550-040 Manual de usuario
Steren
Steren 207-390 Manual de usuario
Steren
Steren 208-140 Manual de usuario
Steren
Steren 506-072 Manual de usuario
Steren
Steren 901-750 Manual de usuario
Steren
Steren 208-151 Manual de usuario
Steren
Steren ELI-030 Manual de usuario
Steren
Steren 207-340 Manual de usuario
Steren
Steren 208-150 Manual de usuario
Steren
Steren 208-154 Manual de usuario
Steren
Steren ELI-030 Manual de usuario
Steren
Steren 252-900 Manual de usuario
Steren
Steren 208-142 Manual de usuario
Steren
Steren ELI-030 Manual de usuario
Steren
Steren 208-156 Manual de usuario
Steren
Steren 208-144 Manual de usuario
Steren
Steren 910-050 Manual de usuario
