Stelpro SEFL series Manual de usuario

INS_SEFL-U 0609

(Replacement component list included)

User’s guide

‘‘SEFL’’ series

Electric furnace

This guide must be read carefully by the installer.

Then, the installer must give it to the user.

www.stelpro.com

For further information or to consult this guide on line, please visit our Web site.

This unit complies with

the CSA standards

This unit is approved according

to the Canadian and American

manufacturing standards.

INS_SEFL-U 0609

Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future reference.

If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.

This product must be installed by a qualified person and connected by a certified electrician, according to the electrical and building codes effective in your

region.

The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.

Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.

Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.

This unit must be grounded.

Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.

Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).

If the unit’s capacity is insufficient for the size of the house, it will be in operation continuously, and may become defective earlier.

Respect distances and positions indicated in the installation section.

If the installer or user modifies the unit, they will be held responsible for any damage resulting from this modification, and the CSA certification could be void.

This unit must not come into contact with a water source and must be protected from splashes (e.g. a wet mop). Do not use it if any part has been immersed.

Moreover, do not turn it on or off when standing in water or if your hands are wet.

When cutting a piece of steel for the installation of the return duct, do not damage electrical wiring of the unit.

Because this unit is hot when in use, it may pose risks even in normal operation. Therefore, be careful and responsible when using it. To avoid burns, do not let

bare skin touch hot surfaces. Let the unit cool down for a few minutes before handling it (it stays warm for some time after shut-down).

Never block air vents. This obstruction could lead to overheating, which could result in a fire.

Do not insert or allow foreign objects to enter any air vent as this may cause electric shocks, fires, or damages to the unit.

This unit has hot and arcing or sparking parts inside. It is not designed to be used or stored in wet areas or areas containing flammable liquids, combustible materials

or corrosive, abrasive, chemical, explosive and flammable substances such as, but not limited to, gasoline, paint, chlorine and cleaning products.

Some areas are dustier than others. Thus, it is the user’s responsibility to evaluate if the filter must be changed based on the amount of dirt accumulated on it.

Accumulated dirt can lead to a component malfunction or discoloration (yellowing). It may cause a fire hazard if not installed and maintained in accordance with

these instructions.

Thermal protection activation indicates that the unit has been subjected to abnormal operating conditions. If the thermal protection remains activated or activates

and deactivates repeatedly, it is recommended that a qualified electrician or a certified repair centre examine the unit in order to make sure it is not damaged. (Refer

to the limited warranty).

If the unit is damaged or defective, cut off power supply at circuit breaker/fuse and call a certified repair centre. (Refer to the limited warranty).

Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.

WARNING WARNING WARNING WARNING

OPERATION

Fan control - Continuous low speed

AUTO ON

Waiting for heating or air-

conditioning demands,

as applicable.

Continuous ventilation

ensuring temperature

uniformity in all rooms

and improving ﬁltration

and

humidiﬁcation systems.

MAINTENANCE

N.B. In order for the warranty to be valid, the unit must be cleaned regularly. Moreover, a qualiﬁed technician must examine your furnace on a

regular basis.

Cut off power supply at circuit breaker/fuse before cleaning the unit. Use a soft rag for dusting. When cleaning, use only a damp rag and non-abrasive dish soap.

Do not use abrasive or chemical cleaners because they can damage the ﬁnishing. If the unit is used in a very dusty location, use a vacuum brush to remove dust

and other foreign objects.

Do not use cleaning products identiﬁed with these symbols:

N.B. Note that there is electrical current to the unit even if the thermostat is off. Meaning that there is a risk of electric shock as long as the unit

is energized.

INS_SEFL-U 0609

Preventive maintenance

Do not try to repair your furnace yourself. Call a qualiﬁed technician. However, before calling a technician, check the following points.

1) Make sure fuses or circuit breakers are activated.

2) Adjust the temperature set point of the thermostat above the ambient temperature. If heating does not start, cut off the power supply and call a techni-

cian.

N.B. When calling a technician for maintenance or to order a replacement part, specify the model of your furnace as well as its serial number.

Air ﬁlter

Excessive dust or dirt accumulation can block the airﬂow, forcing the unit to work harder to maintain the desired temperature. Therefore, it uses more energy and

increases heating costs.

Since the air ﬁlter supplied is disposable, you should replace it two to four times a year, according to the model used and the installation area. Dirtier areas can

require more than four ﬁlter changes.

To replace a dirty ﬁlter, open the access door to the ﬁlter, remove the old ﬁlter and insert the new one inside the rack. Make sure the new ﬁlter has the same techni-

cal speciﬁcations and size as the previous one.

N.B. Never operate the unit without a ﬁlter in place.

Every time a ﬁlter is changed, you should check the following points.

- Excessive accumulation of dirt or dust on furnace components.

- Presence of water inside or outside the furnace.

If you encounter any of these problems, do not operate the furnace. Call a qualiﬁed technician.

Blower

The blower motor is sealed and permanently lubricated, so it is not necessary to lubricate it.

Even if you change the ﬁlter frequently, the blower’s blades and motors will become dust laden after a few months. The entire blower assembly should be inspect-

ed annually. If needed, vacuum out the dust. If you cannot clean the blower without removing it from the furnace, this service must be performed by a qualiﬁed

technician.

TROUBLESHOOTING

If you encounter a problem, check the following table before calling a technician. Should modiﬁcation or servicing be required, make sure the technician uses only

factory authorized parts, accessories, or kits for this furnace.

PROBLEM DEFECTIVE PART OR PART TO CHECK

The unit does not work - Defective thermostat or wrong thermostat setting or location

- Open circuit breaker or fuse

The unit runs continuously - Blower control switch is on the continuous position

The on/off cycles of the motor are too short or too long - The heat anticipator is incorrectly set or is burned out (if applicable)

Overheating - Defective thermostat or wrong thermostat setting or location

- Defective motor

The thermostat must be set at a much higher or lower temperature than the

desired ambient temperature

-The thermostat is not levelled, needs calibration or is installed in an improper loca-

tion

The desired room temperature cannot be reached - The thermal protections opens the circuit because of duct obstructions or dirty

ﬁlters

- Opened internal breaker

N.B. If you do not solve the problem after checking these points, cut off the power supply at the main electrical panel and contact our customer

service (see the “Limited warranty” section to obtain the phone numbers).

REPLACEMENT COMPONENT LIST

DETAIL A

DETAIL B

#DIAGRAM #PART DESCRIPTION

1 ELF-SEF0521 ELEMENT ASSEMBLY 5kW

2 BLO-004 SQUIRREL CAGE & BLOWER 10-8 FOR 15 TO 20 KW.

3 MO-036-1 MOTOR 1/3HP, 208/240V, 1075 RPM, 4 AD. SPEEDS

INCLUDED

4 PROT-010 THERMAL PROTECTION L-160-40 - 15 TO 20 kW

5 SWI-004 SPDT SWITCH WITHOUT MARKINGS 16 A, 250 V, 3/4 HP,

250 V, T85

6 TRF200050D TRANSFO 240-208/24/50VA (SEC.10.5 &13)

7 REL-005 RELAY 240 V, FORM X, 18 A RES.

7 REL-003 RELAY 24 V, FORM C, 20 A NO, 10 A NC

8 SEQ-005 DOUBLE SEQUENCER 24 V, H1-20 C40-90, H30-90 C1-30

8 SEQ-003 SINGLE SEQUENCER 24 V, H30-90 C1-30

8 SEQ.-007 DOUBLE SEQUENCER 24 V, H40-100 C1-30, H25-60 C25-

9 CAP-010 CAPACITOR 6 UF FOR 1/3 HP AT 240 V WITH SUPPORT

INS_SEFL-U 0609

This limited warranty is offered by Stelpro Design inc. (“Stelpro”) and applies to the following products made by Stelpro: models SEFL15, SEFL18 &

SEFL20. Please read this limited warranty carefully. Subject to the terms of this warranty, Stelpro warrants its products and their components against

defects in workmanship and/or materials for the following period from the date of purchase: 5 years. This warranty applies only to the original purchaser;

it is non-transferable and cannot be extended.

Claim procedure

If at any time during the warranty period the unit becomes defective, you must cut off the power supply at the main electrical panel and contact 1) your in-

staller or distributor, 2) your service center or 3) Stelpro’s customer service department. In all cases, you must have a copy of the invoice and provide the

information written on the product nameplate. Stelpro reserves the right to examine or to ask one of its representatives to examine the product itself

or any part of it before honoring the warranty. Stelpro reserves the right to replace the entire unit, refund its purchase price or repair a defective part. Please

note that repairs made within the warranty period must be authorized in advance in writing by Stelpro and carried out by persons authorized by Stelpro.

Before returning a product to Stelpro, you must have a Stelpro authorization number (RMA). To obtain it, call the customer service department at:

1-800-363-3414 (electricians and distributors - French), 1-800-343-1022 (electricians and distributors - English), or 1-866-766-6020 (consumers).

The authorization number must be clearly written on the parcel or it will be refused.

Conditions, exclusions and disclaimer of liability

This warranty is exclusive and in lieu of all other representations and warranties (except of title), expressed or implied, and Stelpro expressly disclaims and

excludes any implied warranty of merchantability or implied warranty of ﬁtness for a particular purpose.

Stelpro’s liability with respect to products is limited as provided above. Stelpro shall not be subject to any other obligations or liabilities whatsoever, whether

based on contract, tort or other theories of law, with respect to goods or services furnished by it, or any undertakings, acts or omissions relating thereto.

Without limiting the generality of the foregoing, Stelpro expressly disclaims any liability for property or personal injury damages, penalties, special or puni-

tive damages, damages for lost proﬁts, loss of use of equipment, cost of capital, cost of substitute products, facilities or services, shutdowns, slowdowns,

or for other types of economic loss or for claims of a dealer’s customers or any third party for such damages. Stelpro speciﬁcally disclaims all consequen-

tial, incidental and contingent damages whatsoever.

This warranty does not cover any damages or failures resulting from: 1) a faulty installation or improper storage; 2) an abusive or abnormal use, lack of

maintenance, improper maintenance (other than that prescribed by Stelpro) or a use other than that for which the unit was designed; 3) a natural disaster

or an event out of Stelpro’s control, including, but not limited to, hurricanes, tornadoes, earthquakes, terrorist attacks, wars, overvoltage, ﬂooding, water

damages, etc. This warranty does not cover any accidental or intentional losses or damages, nor does it cover damages caused by negligence of the user

or owner of the product. Moreover, it does not cover the cost of disconnection, transport, and installation.

The warranty is limited to the repair or the replacement of the unit or the refund of its purchase price, at the discretion of Stelpro. Any parts replaced or

repaired within the warranty period with the written authorization of Stelpro will be warranted for the remainder of the original warranty period. This warranty

will be considered null and void and Stelpro will have the right to refuse any claims if products have been altered without the written authorization of

Stelpro and if the nameplate numbers have been removed or modiﬁed. This warranty does not cover scratches, dents, corrosion or discoloration caused

by excessive heat, chemical cleaning products and abrasive agents. It does not cover any damage that occurred during the shipping.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some of them do not allow limitations on

how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This warranty gives you speciﬁc legal rights and you may have