STEINDORFF NYMCS-VM400 Manual de usuario

STEINDORFF®

NYMCS-VM400 Instructions

STEINDORFF®

- 1 -

LIST OF CONTENTS

General Rules ............................................................................................................................ 2

Basic Parameters ....................................................................................................................... 2

Parts List .................................................................................................................................... 3

◆Main Device ...................................................................................................................... 3

◆Remote Controller ............................................................................................................. 4

Connect & Outputs ..................................................................................................................... 5

General Use ............................................................................................................................... 6

◆Use Individually ................................................................................................................. 6

◆HDMI ................................................................................................................................. 7

◆USB ................................................................................................................................... 7

Software Installation....................................................................................................... 7

Software Operation ........................................................................................................ 8

＊Icons Definitions ................................................................................................... 8

＊Interface Definitions and Functions ...................................................................... 9

＊Operating Steps ................................................................................................. 11

＊Functions ........................................................................................................... 11

STEINDORFF®

- 2 -

General Rules

NYMCS-VM400 is a multifunctional digital microscope. It realized Full HD, high object distance, multifunction,

multi-output at the same time. With help of the Andonstar measuring software, it can easily meet many different

requirements in many industries, such as industrial overhaul and teaching demonstration. And it’s appearance

design combines more ergonomic consideration, provides users better experience. We sincerely wish this

product can release your eyes and improve your work quality. Thanks for your support.

◆This operation manual allows you to work safely with the digital Microscope. Please keep this manual for your

information. Liability is void for any damage caused by not follow this manual.

◆Failure to follow the warnings and instructions may cause electric shock, fire and/or serious injury.

◆Not following this note can cause permanent damage to the device.

◆Storage and transport: Improper transport can harm the device; Always transport this device in the provided

box in order to prevent damage.

◆Information on disposal: Electronic equipment does not belong to domestic waste, but must be disposed in

accordance with the applicable statutory provisions.

◆In order to bring customers a better experience, we may change the product a little bit during perfecting it. The

description in this instruction is for reference ONLY. Thanks for understanding.

◆Safety

1.Keep the tool dry, clean, free from oil, water, gas or other materials capable of causing corrosion.

2.This appliance is not intended for use by people with limited physical, sensory or mental capabilities.

3.Keep bystanders, children away while operating the tool.

4.Do not overreach, keep proper footing and balance at all time.

Basic Parameters

Image sensor

3 Mega Pixels HD Sensor

Video output

1080P Full HD (via HDMI) ;720P (via PC)

Video format

MOV

Magnification ratio

Up to 260x (HDMI monitor 22 inch)

Photo resolution

12M

Photo format

JPEG

Focus range

5cm to 15cm

Frame rate

Max 30f/s under 600 Lux Brightness

Video-output interface

HDMI/AV

Storage

Micro-SD card, up to 32G (option)

PC support

Yes, for Windows XP/7/8/10, PC software with measurement (gift)

Power source

5V/2A

Stand size

20cm*12cm*17cm

Screen size

5 inch

Accessories

Stand*1, Power Adaptor*1, USB Cable*1, HDMI Cable*1, Manual*1,

IR controller*1

Packing data

28*22*17cm/1.9kg

STEINDORFF®

- 3 -

Parts List

◆Main Device

*Fasten screw: It aim to adjust the compactness between the Lifting stand and the Distance controllers, so users

can fasten the distance from the lens to the object table.

STEINDORFF®

- 4 -

◆Remote Controller

*Frozen: Stop the image on the screen. It works at standby, record and capture modes.

*Zoom in & out: digital zooming in to 4 times.

*Brightness up & down: exposure compensation from +2.0 to -2.0.

*Lock/unlock: to lock the file when it’s recording. So the video file which has been locked won’t be covered by

new files when the memory card is full.

*Sharpness up & down: there are three levels of sharpness: Soft/Normal/Strong. Those two buttons are both

used to switch the levels, but in different orders.

*Contrast up & down: same principle as Sharpness.

*Inverse: refer to pictures in below:

Normal Inverse

*Black & white: refer to pictures in below

Normal Black & White

STEINDORFF®

- 5 -

Connect & Outputs

So generally, it has 5 ways of output including its own monitor can show image itself. And the rest four are: HDMI,

AV/TV, USB and memory card. The image below shows the different ports on the device. In the next few chapters,

there are more details about each of them.

①：AV output. (You need a separated AV cable to connect the device to the monitor, when you need to use AV

output. There is no AV cable in the standard configuration)

②：Memory card. (In order to save video files and capture results)

③：USB output. (You need a separated USB cable to connect the device to the PC, when you need to use USB

output)

④：HDMI output. (You need a separated HDMI cable to connect the device to the HDMI monitor, when you

need to use HDMI output)

⑤：Connect the device to the switch.

STEINDORFF®

- 6 -

⑥：Connect the switch to the power supply.

⑦：Connect the two goose lights to the switch.

⑧：The switch. It has three buttons. The one on the left is ON/OFF, to get or break the connection between the

device and the power supply. The rest two are for the two goose lights. The middle one means “brightness up”,

the right one means “brightness down”.

General Use

◆Use Individually

1. According to the instructions given by last chapters, connect the camera to the power supply like⑤⑥⑦.

2. Press the “ON/OFF” button on the monitor. (Sometimes the camera will switch on automatically when it is

connected to the power supply)

3. Turn on the LED lights, adjust the object distance wheel and the focus controller to get the image that you

want.

4. Use the “UP/DOWN” to zoom in/out.

*To switch mode:

1. Press “M” shortly. (Or press the “Mode” on the remote)

2. Icons definition in different modes:

: standby mode; : capture mode; : record mode; : image playback mode

: video playback mode (If the files are videos, press “OK” to play the video file)

: Lock the file which is being recording

*To set the menu for record mode:

1. Press “M” for few seconds until on the screen shows the menu. (Or press “MENU” on the remote.)

2. Press “UP/DOWN” and use “OK” to choose what to set.

3. Press “M” again when you are done.

*To set the menu for system:

1. Press “M” for few seconds until on the screen shows the menu. Then press “M” again to get into the system

setting menu. (Or press “MENU” on the remote twice)

2. Press “UP/DOWN” and use “OK” to choose what to set.

3. Press “M” again when you are done.

*To set the menu for capture mode:

1. Get into the capture mode and then press “M”.

2. Press “UP/DOWN” and use “OK” to choose what to set.

*To capture pictures, three ways:

STEINDORFF®

- 7 -

1.Press “M” shortly to get into the Capture mode. Press “OK” to take pictures.

2.Press “Capture” on the monitor only.

3.Press “Capture” button on the IR remote to get pictures.

* To record videos:

1.Press “M” shortly to get into the Record mode. Press “OK” to start recording.

2.Press “OK” to stop recording.

PS: Press “Lock & unlock” on the remote to lock the file when it’s recording. So the video file won’t be covered

by new files when the memory card is full.

◆HDMI

·First, make sure that the monitor connecting to the microscope is literally HDMI monitor. Otherwise it won’t

perform as good as we expected.

·Second, connect the microscope to the HDMI monitor, also, connect it to the power supply. Because there is

no built-in battery in the device, so make sure the microscope is always in charging when you use it.

·Third, turn on the microscope and adjust the distance. Then put the object on the table and adjust the focus

controller.

·It won’t show anything on its own screen when it is connected to other equipment. So it’s normal that when you

use it as HDMI output, the 5 inch screen keeps being dark.

·You still can take pictures and save them if you have a memory card inside the microscope. But you can’t record

videos in this output mode.

FAQ

•Why is there no image on the monitor?

Please check all the cables connect properly and also make sure the device is switched on.

•Why the image is not clear?

Please adjust the object distance and the focus controller, check the direction of the LED lights, and make sure

the lens is clean enough.

•Remote doesn’t work?

There is no battery inside of the remote as standard configuration. Please check if there is battery in the remote.

•Why is there no image in playback model?

Sometimes the video file is too big, the system needs time to process.

•SD card error

Make sure the memory card you use is certified and quality. Format the memory card in the system first, then try

again.

◆USB

Software Installation

＊Download the software first:

So far the measuring software “Andonstar” can only support Windows system. If you can’t open the links or get

problem with downloading these files, please ask customer service to send you separately. You can also go visit

STEINDORFF®

- 8 -

our website and download from there.

System support:

Windows XP SP3, Windows 7,Windows 8, Windows10

Process circumstances：

Microsoft.Net Framework 4.0

Microsoft Visual C++ 2010 Runtime

If there isn't either of the runtimes above mentioned, there would be mistake during installation.

＊Open the zip file that you’ve download and run it.

Software Operation

*Icons Definitions

Zoom In

Measuring a 3points angle (degree)

Normal

Distance of parallel lines(Length)

Zoom out

Distance of a point and a line (Length)

Undoes the last action

Distance of 2 circles (Radius, length)

Cross hairs (crosier,4 grid, 8 grid)

Distance of a line and a circle(Radius, length)

Distance of 2 horizontal points

Add a square mark

Distance of 2 vertical points

Add a circle mark

Distance of any 2 points

Add text

Measuring a rectangular

(width,height, circumference&area)

Distance of 2 lines(Length)

Measuring an ellipse(Long-axis radius, short-axis

radius, circumference&area)

3 points circle

(radius, circumference&area)

Measuring a radius circle(radius, circumference&area)

Edge detection

Measuring a diameter circle

(diameter, circumference&area)

Brightness increase/decrease

Measuring a 3 points circle(radius, circumference&area)

Flip horizontal

Measuring a 3 points arc

(radius,degree,circumference&area)

Sharpen

Measuring a polygon (circumference&area)

Smooth

Measuring fold-lines (length)

Take a picture

Measuring a 4 points angle (degree)

Take a video

STEINDORFF®

- 9 -

＊Interface Definitions and Functions

①Main menu:

Here, users can open different devices or lead in pictures to observe or edit, do video setting or save setting,

choose which windows to show or hide etc.

②toolbar:

Here are the tools that would be useful for users to do measuring and image analysis. Definition and function of

different tools would be given in chapter “Icons definitions”. Users can choose to hide or show this toolbar in

“View→Toolbars and Docking Windows→Standard”.

③Pictures browser:

Here is where users can review all pictures they’ve captured. Users can also edit the picture by right clicking the

picture and open it in the main operating window. Choose “View→Toolbars and Docking Windows→Picture

browser” to show or hide this window.

④Secondary operating window:

The image showing in this window always follows your cursor, and with a bigger magnification. With help of this

window, the result of measuring can be much more precisely.

It belongs to window “Pictures browser”.

⑤Main operating window:

This window shows the full view from the microscope. And it is also the place where users do measuring and

image analysis.

⑥Calibration Management and Measuring Results:

These two windows shows at the same place, users can switch at the bottom of this window.

Tabla de contenidos

Otros manuales de Microscopio de STEINDORFF

STEINDORFF

STEINDORFF NYMCS-1500 Manual de usuario

STEINDORFF

STEINDORFF S-1260 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-290 Manual de usuario

STEINDORFF

STEINDORFF CX50 Series Manual de usuario

STEINDORFF

STEINDORFF NYMCS-620 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-931 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-1290 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-342 Manual de usuario

STEINDORFF

STEINDORFF NYMC38000 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-1262 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-320 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-310 Manual de usuario

STEINDORFF

STEINDORFF NYMC62B00 Manual de usuario

STEINDORFF

STEINDORFF NYMC0035000C Manual de usuario

STEINDORFF

STEINDORFF NYMCS-360 Manual de usuario

STEINDORFF

STEINDORFF S-3000 Series Manual de usuario

STEINDORFF

STEINDORFF S-340 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-615 Manual de usuario

STEINDORFF

STEINDORFF S-VM300 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-212 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-VM2000N Manual de usuario

STEINDORFF

STEINDORFF NYMCS-1701 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-603 Manual de usuario

STEINDORFF

STEINDORFF NYMCS-702 Manual de usuario

Manuales populares de Microscopio de otras marcas

Thermo Scientific

Thermo Scientific Nicolet iN10 Guía

National

National DC3-163 Manual de usuario

KERN Optics

KERN Optics OPE-1 Manual de usuario

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Manual de usuario

Prior

Prior Lux POL Manual de usuario

Opitec

Opitec Smartscoop 115615 Manual de usuario

KERN

KERN OPO-1 Manual de usuario

Topcon

Topcon SP-1P Manual de usuario

Motic

Motic PA43 Manual de usuario

Leica

Leica DVM5000 Guía del usuario

MshOt

MshOt MZ62 Manual de usuario

KERN Optics

KERN Optics OZR-5 Manual de usuario

VWR

VWR VisiScope 384 Series Manual de usuario

Nikon

Nikon ECLIPSE E200 POL Manual de usuario

Leica

Leica DI C800 Manual

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Manual de usuario

Olympus

Olympus SZ61 Manual de usuario