Steelcase Elective Elements Storage Manual de usuario
Page 1 of 4
939500237 Rev J
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
© 2018 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
Elective Elements Plinth Base, Garland,
Walden - Underworksurface Storage
2
3
4
27-1/2" HIGH
ONE-HIGH HIGH PEDESTAL
5/32" Allen Wrench
1.5 HIGH
NOTICE
3
Steps for correct installation of
soft close drawers
1
2
1
2
3
Pull LH and RH suspensions to full extents
Find and disengage rear posts, LH and RH
Align drawer suspensions and install
1134607001
Soft close mechanism
can be damaged if this
step is skipped.
RH post is
shown here
in yellow
1. Unlock and remove drawers (if any)
from pedestal(s).
2. Turn worksurface over onto clean,
soft surface.
3. Lower pedestal(s) onto worksurface
and position as shown.
Page 2 of 4
939500237 Rev J
1
To remove drawers
push lever down on one
side, and up on the other.
Position pedestals
flush with modesty panel
and with front and
sides of worksurface
(with drawer fronts installed).
3
3
15/16"
(24 mm)
A removable shelf is used on a 1.5 high
pedestal to allow access to the stretchers.
Pull the shelf out and off from the
wire holders that secure
it on each side.
WIRE SHELF HOLDER
fit into routs in sides
of shelf (both sides).
4. Secure pedestal(s) to worksurface.
5. Carefully turn assembly over, adjust
leveling glides as needed, and reinstall
drawers.
a) Push drawer rails back into pedestal.
b) Pull bearing cages into forward position.
c) Check to see if lock is funtioning properly.
If not, follow illustration to adjust.
NOTE: Units are factory adjusted and should
not require adjustment. If lock is not
functioning properly, first confirm that the
storage unit is leveled properly using the
leveler glides (step 5). If the lock continues to
function improperly, then adjustment may be
necessary.
Page 3 of 4
939500237 Rev J
(4) screws per
pedestal through
holes in stretchers,
1-1/2" pan head
4
5b
5a
Use a 5/32" Allen Wrench to adjust
locking mechanism. Rotate cam
clockwise for upward movement,
counterclockwise to move down.
5c
NOTE: for 18” deep, 1.5 high
storage use the steel trough
as the rear stretcher. Use
1” screws.
FOR LOCK ADJUSTMENT:
Problem: The Lock does not restrain the drawer.
Rotate the cam counterclockwise by a quarter of a turn.
This motion lowers the lock fork resulting in greater lift
of the lock bar. Turn the key to the locked position and
check the drawer to confirm that the lock is working
correctly. Repeat this step if necessary.
Problem: The drawers lock, but an audible click
is heard when closing the drawer. Rotate the cam
clockwise by a quarter of a turn. This motion raises the
lock fork relative to the lock pin, eliminating an interference
condition. Turn the key to the locked position and check
the drawer to confirm that the lock is working correctly.
Repeat this step if necessary.
CAM PIN
Best Position:
touches the
underside of the
actuator fork.
Bad Position:
Lock may not
work when it
touches the
bottom of the
actuator fork.
Acceptable
Position:
Page 4 of 4
939500237 Rev J
UP/DOWN
IN/OUT
SIDE TO SIDE
DOOR HINGE
HINGE ADJUSTMENT
A #2 screwdriver is recommended for adjusting hinge.
Otros manuales para Elective Elements Storage
4
Este manual sirve para los siguientes modelos
2
Otros manuales de Almacenamiento de Steelcase
Manuales populares de Almacenamiento de otras marcas
Spectra Logic
Spectra Logic T-Series Spectra T50e Manual de usuario
Panasonic
Panasonic LKM-F931-1 Manual de usuario
Tabernus
Tabernus Enterprise Erase E2400 Manual de usuario
Rocstor
Rocstor COMMANDER 3F series Manual de usuario
HP
HP P9000 Manual de usuario
Western Digital
Western Digital Ultrastar Data60 Manual de usuario