State Water Heaters Gas Manual de usuario

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters

■Limited Warranty Outline

–If the tank should leak any time during the ﬁrst three years, under

the terms of the warranty, State Water Heaters will repair or replace

heater; installation, labor, handling and local delivery extra.

– NOTE: This Outline Is NOTA Warranty. For complete information,

consult the written warranty or State Water Heaters.

■TPO – Oil Fired Models: No. 1 or 2 Oil

–Multi-annular fuel containment combustor head

–Available for ﬁring light fuel oils including diesel

–Oil ignition transformer

–Integral 2-stage fuel unit

–Squirrel cage blower

–Oil safety valve

■TPD – Dual Fuel Gas/Oil: Natural Gas or Propane & No. 1 or 2 Oil

–Multi-annular fuel containment combustor head

–Gas electric pilot and gas ignition transformer

–Pilot and main pressure regulators

–Air safety switch

–Manual fuel selector switch

–Integral 2-stage fuel unit

–Squirrel cage blower

■Meets or exceeds current edition of ASHRAE/IES-90.1-1999.

■Low NOX– TPX Low NOXmodels meet or exceed current Texas and

California SCAQMD air quality standards.

■UL – Entire unit UL listed (File No. MH11631).

■Glass-Lined Tank – Exclusive corrosion protection with glass-

lining on all interior surfaces. Multiple anodes provide even more

corrosion protection.

■

ASME Construction Standard – 160 PSI working pressure on all models.

■Powered Gas Burner – Powered burner has electronic ﬂame

safeguard control with intermittent spark ignition. Also included are

main and pilot automatic gas valves plus gas pressure regulators,

diaphragm air switch for proof of blower operation.

–TPX Low NOXModels are factory standard with modulating ﬁre.

The burner automatically adjusts the ﬁring rate and the Btu output

to maintain precise system temperature control.

■Fully Automatic Controls With Safety Shutoff – High temperature

limit control (manual reset). ASME rated temperature and pressure

relief valve. Hinged door control compartment for ease of access. Two

thermostats, upper and lower, for accurate temperature control.

Standard control is for 120˚F - 180˚F water service.

■Jacket And Insulation – Heavy gauge steel with baked powder coat

ﬁnish. Insulated with high-density foam insulation that meets or

exceeds all required standards.

■Professional Start-Up Service Furnished To Assure Most Efﬁcient

Combustion And Safe Initial Start-Up.

■Other Features

–Two layers of high temperature ceramic ﬁber insulation in

combustion chamber

–Flame inspection port opening

–Mounted on rugged channel iron skids

–Combination temperature and pressure gauge

–Low water cutoff

–ASME rated temperature and pressure relief valve

–Barometric draft regulator

–Two cleanout inspection openings

–120 volt control circuit

–Drain valve

–Removable lifting lugs

■Options

–Factory Mutual approved control arrangement

–Industrial Risk Insurance (IRI Gas Train)

–5 year or 10 year limited warranty

–High or low water pressure switch

–180°F water service thermostats

–A.G.A. rated T & P Valve

–Modular graphic burner systems management on heaters with

270,000 Btu input and over

–Combustion Air intake Adapter

Nominal Input Output (Gallons)

Storage Rating Ship.

Model Number Capacity BTU/Hr. First Recovery Dimensions In Inches Wt. Motor HP

U.S. Natural Hour w/Burner 120V 60 Hz 1

Gallons Gas Rating 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J (lbs.)

TPG 150 140 NEA 150 140,000 256 170 136 97 831⁄214 1⁄2273⁄411⁄4361⁄25 47 73 1292

TPG 150 199 NEA 150 199,000 313 241 193 138 831⁄214 1⁄2273⁄411⁄4361⁄26 47 73 1292 1⁄7HP - 2.5 Amps

TPG 150 255 NEA 150 255,000 367 359 247 176 831⁄214 1⁄2273⁄411⁄4361⁄26 47 73 1292

TPG 150 270 NEA 150 270,000 382 327 262 187 831⁄214 1 273⁄411⁄4361⁄2657

1⁄273 1397

TPG 150 400 NEA 150 400,000 507 485 387 277 831⁄214 1 273⁄411⁄4361⁄2757

1⁄273 1397 1⁄4HP - 4.6 Amps

TPG 150 540 NEA 150 540,000 644 654 524 374 831⁄214 1 273⁄411⁄4361⁄2857

1⁄273 1505

TPG 150 720 NEA 150 720,000 818 873 698 499 831⁄214 11⁄4273⁄411⁄4361⁄210 571⁄273 1510 1⁄3HP - 5.5 Amps

TPG 200 300 NEA 200 300,000 451 364 291 208 831⁄215 1 321⁄211⁄2443⁄4666

1⁄273 2098 1⁄4HP - 4.6 Amps

TPG 200 600 NEA 200 600,000 742 727 582 416 831⁄215 1 321⁄211⁄2443⁄4866

1⁄273 2098

TPG 200 800 NEA 200 800,000 936 970 776 554 831⁄215 11⁄4321⁄211⁄2443⁄410 661⁄273 2103 1⁄3HP - 5.5 Amps

TPG 200 1000 NEA 200 1,000,000 1130 1212 970 693 831⁄215 11⁄4321⁄211⁄2443⁄410 661⁄273 2103

TPG 200 1250 NEA 200 1,250,000 1372 1515 1212 866 831⁄215 11⁄4321⁄211⁄2443⁄412 661⁄273 2467 1⁄2HP - 7.4 Amps

TPG 200 1500 NEA 200 1,500,000 1615 1818 1455 1039 831⁄215 11⁄2321⁄211⁄2443⁄412 811⁄273 2757

TPG 300 300 NEA 300 300,000 531 364 291 208 911⁄214 1 261⁄211⁄2443⁄4666

1⁄283 2150 1⁄4HP - 4.6 Amps

TPG 300 600 NEA 300 600,000 822 727 582 416 911⁄214 1 261⁄211⁄2443⁄4866

1⁄283 2150

TPG 300 800 NEA 300 800,000 1016 970 776 554 911⁄214 11⁄4261⁄211⁄2443⁄410 661⁄283 2308 1⁄3HP - 5.5 Amps

TPG 300 1000 NEA 300 1,000,000 1210 1212 970 693 911⁄214 11⁄4261⁄211⁄2443⁄410 661⁄283 2308

TPG 300 1250 NEA 300 1,250,000 1452 1515 1212 866 911⁄214 11⁄4261⁄211⁄2443⁄412 661⁄283 2584 1⁄2HP - 7.4 Amps

TPG 300 1500 NEA 300 1,500,000 1695 1818 1455 1039 911⁄214 11⁄2261⁄211⁄2443⁄412 811⁄283 2774

TPG 400 600 NEA 400 600,000 902 727 582 416 911⁄215 1 321⁄2255876

1⁄281 3207 1⁄4HP - 4.6 Amps

TPG 400 800 NEA 400 800,000 1096 970 776 554 911⁄215 11⁄4321⁄22551076

1⁄281 3212

TPG 400 1000 NEA 400 1,000,000 1290 1212 970 693 911⁄215 11⁄4321⁄22551076

1⁄281 3212 1⁄3HP - 5.5 Amps

TPG 400 1250 NEA 400 1,250,000 1532 1515 1212 866 911⁄215 11⁄4321⁄22551276

1⁄281 3212

TPG 400 1500 NEA 400 1,500,000 1775 1816 1455 1039 911⁄215 11⁄2321⁄22551291

1⁄281 3402

TPG 400 1750 NEA 400 1,750,000 2017 2121 1697 1212 911⁄215 2 321⁄22551491

1⁄281 3528 1⁄2HP - 7.4 Amps

TPG 400 2000 NEA 400 2,000,000 2259 2424 1939 1385 991⁄215 2 321⁄22551491

1⁄289 3669

TPG 500 2250 NEA 500 2,250,000 2582 2727 2182 1558 110 15 2 321⁄22551691

1⁄2100 4277 3⁄4HP - 10.2 Amps

TPG 500 2500 NEA 500 2,500,000 2824 3030 2424 1732 110 15 2 321⁄22551691

1⁄2100 4419

TPG 600 720 NEA 600 720,000 1178 873 698 499 119 15 11⁄4321⁄22551076

1⁄2109 3667

TPG 600 1000 NEA 600 1,000,000 1450 1212 970 693 119 15 11⁄4321⁄22551076

1⁄2109 3667 1⁄3HP - 5.5 Amps

TPG 600 1250 NEA 600 1,250,000 1692 1515 1212 866 119 15 11⁄4321⁄22551276

1⁄2109 3667

TPG 600 1500 NEA 600 1,500,000 1935 1816 1455 1039 119 15 11⁄2321⁄22551291

1⁄2109 3837

TPG 600 1750 NEA 600 1,750,000 2177 2121 1697 1212 119 15 2 321⁄22551491

1⁄2109 3837 1⁄2HP - 7.4 Amps

TPG 600 2000 NEA 600 2,000,000 2419 2424 1939 1385 119 15 2 321⁄22551491

1⁄2109 3837

TPG 600 2250 NEA 600 2,250,000 2662 2727 2182 1558 119 15 2 321⁄22551691

1⁄2109 4477 3⁄4HP - 10.2 Amps

TPG 600 2500 NEA 600 2,500,000 2904 3030 2424 1732 119 15 2 321⁄22551691

1⁄2109 4619

TPG Power Gas Large Volume Commercial Water Heaters

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

SPECIFICATIONS

Certiﬁed Minimum Installation Clearances to Combustibles:

Front: 18 inches

Back: 0 inches

Sides: 0 inches

Top: 5 inches

A clearance of 24 inches should be maintained from

serviceable parts such as relief valve, power burner, drain

valve and anodes (anodes are located on side above cold

water inlet).

Minimum gas supply pressure: 7 Inches W.C.

Maximum gas supply pressure: 13 Inches W.C.

TPG models are Category I appliances (Fan Assisted) and

require a negative draft. These units should only be

commonly vented with other Category I negative draft

appliances per the latest addition of the National Fuel Gas

Code. An approved/listed Type “B” venting material is

recommended. A negative draft of -0.02˝ to -0.07 is required

in the vent.

TPG models are available in both natural gas and propane. To

order propane, change the “N” to “P” in the model number.

Example: TPG 150 140 PEA

ASME

TPX Power Low NOXLarge Volume Commercial Water Heaters

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

Certiﬁed Minimum Installation Clearances to Combustibles:

Front: 18 inches

Back: 0 inches

Sides: 0 inches

Top: 5 inches

A clearance of 24 inches should be maintained from serviceable parts such as relief valve, power

burner, drain valve and anodes (anodes are located on side above cold water inlet).

Minimum gas supply pressure: 7 Inches W.C.

Maximum gas supply pressure: 13 Inches W.C.

TPX models are Category I appliances (Fan Assisted) and require a negative draft. These units should

only be commonly vented with other Category I negative draft appliances per the latest addition of the

National Fuel Gas Code. An approved/listed Type “B” venting material is recommended. A negative draft

of -0.02˝ to -0.07 is required in the vent.

Nominal Input Output (Gallons)

Storage Rating

Model Number Capacity BTU/Hr. First Recovery Dimensions In Inches Motor HP

U.S. Natural Hour 120V 60 Hz 1

Gallons Gas Rating 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J

PX 150 400 NEA 150 400,000 507 485 387 277 831⁄214 1 273⁄411⁄454 7 571⁄273 1⁄7HP - 2.5 Amps

TPX 150 540 NEA 150 540,000 644 654 524 374 831⁄214 1 273⁄411⁄454 8 571⁄273

TPX 200 800 NEA 200 800,000 936 970 776 554 831⁄215 11⁄4321⁄211⁄260 10 72 73

TPX 200 1000 NEA 200 1,000,000 1130 1212 970 693 831⁄215 11⁄4321⁄211⁄260 10 72 73

TPX 200 1250 NEA 200 1,250,000 1372 1515 1212 866 831⁄215 11⁄4321⁄211⁄260 12 72 73

TPX 200 1500 NEA 200 1,500,000 1615 1818 1455 1039 831⁄215 11⁄2321⁄211⁄260 12 72 73

TPX 300 800 NEA 300 800,000 1016 970 776 554 911⁄214 11⁄4261⁄211⁄260 10 72 83

TPX 300 1000 NEA 300 1,000,000 1210 1212 970 693 911⁄214 11⁄4261⁄211⁄260 10 72 83 1⁄3HP - 8.6 Amps

TPX 300 1250 NEA 300 1,250,000 1452 1515 1212 866 911⁄214 11⁄4261⁄211⁄260 12 72 83

TPX 300 1500 NEA 300 1,500,000 1695 1818 1455 1039 911⁄214 11⁄2261⁄211⁄260 12 72 83

TPX 400 800 NEA 400 800,000 1096 970 776 554 911⁄215 11⁄4321⁄2267108481

TPX 400 1000 NEA 400 1,000,000 1290 1212 970 693 911⁄215 11⁄4321⁄2267108481

TPX 400 1250 NEA 400 1,250,000 1532 1515 1212 866 911⁄215 11⁄4321⁄2267128481

TPX 400 1500 NEA 400 1,500,000 1775 1816 1455 1039 911⁄215 11⁄2321⁄2267128481

TPX 400 1750 NEA 400 1,750,000 2017 2121 1697 1212 911⁄215 2 321⁄22551491

1⁄281 1 HP - 12.4 Amps

TPX 400 2000 NEA 400 2,000,000 2259 2424 1939 1385 991⁄215 2 321⁄22551491

1⁄289

TPX 600 1000 NEA 600 1,000,000 1450 1212 970 693 119 15 11⁄4321⁄22 67 10 84 109

TPX 600 1250 NEA 600 1,250,000 1692 1515 1212 866 119 15 11⁄4321⁄22 67 12 84 109 1⁄3HP - 8.6 Amps

TPX 600 1500 NEA 600 1,500,000 1935 1816 1455 1039 119 15 11⁄2321⁄22 67 12 84 109

TPX 600 1750 NEA 600 1,750,000 2177 2121 1697 1212 119 15 2 321⁄22551491

1⁄2109 1 HP - 12.4 Amps

TPX 600 2000 NEA 600 2,000,000 2419 2424 1939 1385 119 15 2 321⁄22551491

1⁄2109

SPECIFICATIONS

ASME

TPO Power Oil Large Volume Commercial Water Heaters

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

Actual

Input Output (Gallons)

Storage

Rating

Ship.

Model Number Capacity

BTU/Hr.

Firing Recovery Dimensions In Inches Wt. Motor HP

U.S. Rate w/Burner 120V 60 Hz 1

Gallons GPH 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J (lbs.)

TPO 150 140 OEA 163 140,000 1 170 136 97 831⁄214 –

273⁄4

11⁄4361⁄25 47 73 1292

TPO 150 199 OEA 163 199,000 1.4 241 193 138 831⁄214 –

273⁄4

11⁄4361⁄26 47 73 1292 1⁄7HP - 4.4 Amp

TPO 150 255 OEA 163 255,000 1.8 309 247 176 831⁄214 –

273⁄4

11⁄4361⁄26 47 73 1292

TPO 150 270 OEA 163 270,000 1.9 327 262 187 831⁄214 –

273⁄4

11⁄4361⁄2657

1⁄273 1397

TPO 150 400 OEA 151 400,000 2.8 485 387 277 831⁄214 –

273⁄4

11⁄4361⁄2757

1⁄273 1397

TPO 150 540 OEA 151 540,000 3.8 654 524 374 831⁄214 –

273⁄4

11⁄4361⁄2857

1⁄273 1505

TPO 150 720 OEA 145 720,000 5.1 873 698 416 831⁄214 –

273⁄4

11⁄4361⁄210 571⁄273 1510 1⁄4HP - 4.6 Amp

TPO 200 300 OEA 221 300,000 2.1 364 291 208 831⁄215 – 321⁄211⁄2443⁄4666

1⁄273 2098

TPO 200 600 OEA 221 600,000 4.2 727 582 416 831⁄215 – 321⁄211⁄2443⁄4866

1⁄273 2098

TPO 200 800 OEA 221 800,000 5.7 970 776 554 831⁄215 – 321⁄211⁄2443⁄410 661⁄273 2103

TPO 200 1000 OEA 201 1,000,000 7.1 1212 970 693 831⁄215 – 321⁄211⁄2443⁄410 661⁄273 2103 1⁄3HP - 5.5 Amp

TPO 200 1250 OEA 201 1,250,000 8.9 1515 1212 866 831⁄215 – 321⁄211⁄2443⁄412 661⁄273 2467

TPO 200 1500 OEA 201 1,500,000 10.7 1818 1455 1039 831⁄215 – 321⁄211⁄2443⁄412 811⁄273 2757 3⁄4HP - 10.2 Amp

TPO 300 300 OEA 300 300,000 2.1 364 291 208 911⁄214 – 261⁄211⁄2443⁄4666

1⁄283 2150 1⁄4HP - 4.6 Amp

TPO 300 600 OEA 300 600,000 4.2 727 582 416 911⁄214 – 261⁄211⁄2443⁄4866

1⁄283 2150

TPO 300 800 OEA 300 800,000 5.7 970 776 554 911⁄214 – 261⁄211⁄2443⁄410 661⁄283 2308

TPO 300 1000 OEA 300 1,000,000 7.1 1212 970 693 911⁄214 – 261⁄211⁄2443⁄410 661⁄283 2308 1⁄3HP - 5.5 Amp

TPO 300 1250 OEA 300 1,250,000 8.9 1515 1212 866 911⁄214 – 261⁄211⁄2443⁄412 661⁄283 2584

TPO 300 1500 OEA 300 1,500,000 10.7 1818 1455 1039 911⁄214 – 261⁄211⁄2443⁄412 811⁄283 2774 3⁄4HP - 10.2 Amp

TPO 400 600 OEA 411 600,000 4.2 727 582 416 911⁄215 – 321⁄2255876

1⁄281 3207 1⁄4HP - 4.6 Amp

TPO 400 800 OEA 411 800,000 5.7 970 776 554 911⁄215 – 321⁄22551076

1⁄281 3212

TPO 400 1000 OEA 411 1,000,000 7.1 1212 970 693 911⁄215 – 321⁄22551076

1⁄281 3212 1⁄3HP - 5.5 Amp

TPO 400 1250 OEA 411 1,250,000 8.9 1515 1212 866 911⁄215 – 321⁄22551276

1⁄281 3212

TPO 400 1500 OEA 397 1,500,000 10.7 1816 1455 1039 911⁄215 – 321⁄22551291

1⁄281 3402

TPO 400 1750 OEA 397 1,750,000 12.5 2121 1697 1212 911⁄215 – 321⁄22551491

1⁄281 3528 3⁄4HP - 10.2 Amp

TPO 400 2000 OEA 397 2,000,000 14.2 2424 1939 1385 991⁄215 – 321⁄22551491

1⁄289 3669

TPO 500 2250 OEA 495 2,250,000 16 2727 2182 1558 110 15 – 321⁄22551691

1⁄2100 4277 1 HP - 16 Amp

TPO 500 2500 OEA 495 2,500,000 17.8 3030 2424 1732 110 15 – 321⁄22551691

1⁄2100 4419

TPO 600 720 OEA 594 720,000 5.1 873 698 499 119 15 – 321⁄22551076

1⁄2109 3667 1⁄4HP - 4.6 Amp

TPO 600 1000 OEA 594 1,000,000 7.1 1212 970 693 119 15 – 321⁄22551076

1⁄2109 3667

TPO 600 1250 OEA 594 1,250,000 8.9 1515 1212 866 119 15 – 321⁄22551276

1⁄2109 3667 1⁄3HP - 5.5 Amp

TPO 600 1500 OEA 594 1,500,000 10.7 1816 1455 1039 119 15 – 321⁄22551291

1⁄2109 3837

TPO 600 1750 OEA 594 1,750,000 12.5 2121 1697 1212 119 15 – 321⁄22551491

1⁄2109 3837 3⁄4HP - 10.2 Amp

TPO 600 2000 OEA 594 2,000,000 14.3 2424 1939 1385 119 15 – 321⁄22551491

1⁄2109 3837

TPO 600 2250 OEA 575 2,250,000 16 2727 2182 1558 119 15 – 321⁄22551691

1⁄2109 4477 1 HP - 16 Amp

TPO 600 2500 OEA 575 2,500,000 17.8 3030 2424 1732 119 15 – 321⁄22551691

1⁄2109 4619

SPECIFICATIONS

Certiﬁed Minimum Installation Clearances to Combustibles:

Front: 18 inches

Back: 0 inches

Sides: 0 inches

Top: 5 inches

A clearance of 24 inches should be maintained from

serviceable parts such as relief valve, power burner, drain

valve and anodes (anodes are located on side above cold

water inlet).

State Titan TPO models are Category I appliances

(Fan Assisted) and require a negative draft. These units

should only be commonly vented with other Category I

negative draft appliances per the latest addition of the

National Fuel Gas Code. An approved/listed Type “B” venting

material is recommended. A negative draft of -0.02˝ to -0.07

is required in the vent.

ASME

Actual

Input Output (Gallons)

Storage

Rating

Ship.

Model Number Capacity

BTU/Hr.

Firing Recovery Dimensions In Inches Wt. Motor HP

U.S. Rate w/Burner 120V 60 Hz 1

Gallons GPH 80°F Rise 100°F Rise 140°F Rise A B C D E F G H J (lbs.)

TPD 150 140 ONEA 163 140,000 1 170 136 97 831⁄214 1⁄2273⁄411⁄4361⁄25 47 73 1292

TPD 150 199 ONEA 163 199,000 1.4 241 193 138 831⁄214 1⁄2273⁄411⁄4361⁄26 47 73 1292 1⁄7HP - 4.4 Amp

TPD 150 255 ONEA 163 255,000 1.8 309 247 176 831⁄214 1⁄2273⁄411⁄4361⁄26 47 73 1292

TPD 150 270 ONEA 163 270,000 1.9 327 262 187 831⁄214 1 273⁄411⁄4361⁄2657

1⁄273 1397

TPD 150 400 ONEA 151 400,000 2.8 485 387 277 831⁄214 1 273⁄411⁄4361⁄2757

1⁄273 1397

TPD 150 540 ONEA 151 540,000 3.8 654 524 374 831⁄214 1 273⁄411⁄4361⁄2857

1⁄273 1505

TPD 150 720 ONEA 145 720,000 5.1 873 698 416 831⁄214 11⁄4273⁄411⁄4361⁄210 571⁄273 1510 1⁄4HP - 4.6 Amp

TPD 200 300 ONEA 221 300,000 2.1 364 291 208 831⁄215 1 321⁄211⁄2443⁄4666

1⁄273 2098

TPD 200 600 ONEA 221 600,000 4.2 727 582 416 831⁄215 1 321⁄211⁄2443⁄4866

1⁄273 2098

TPD 200 800 ONEA 221 800,000 5.7 970 776 554 831⁄215 11⁄4321⁄211⁄2443⁄410 661⁄273 2103

TPD 200 1000 ONEA 201 1,000,000 7.1 1212 970 693 831⁄215 11⁄4321⁄211⁄2443⁄410 661⁄273 2103 1⁄3HP - 5.5 Amp

TPD 200 1250 ONEA 201 1,250,000 8.9 1515 1212 866 831⁄215 11⁄4321⁄211⁄2443⁄412 661⁄273 2467

TPD 200 1500 ONEA 201 1,500,000 10.7 1818 1455 1039 831⁄215 11⁄2321⁄211⁄2443⁄412 811⁄273 2757 3⁄4HP - 10.2 Amp

TPD 300 300 ONEA 300 300,000 2.1 364 291 208 911⁄214 1 261⁄211⁄2443⁄4666

1⁄283 2150 1⁄4HP - 4.6 Amp

TPD 300 600 ONEA 300 600,000 4.2 727 582 416 911⁄214 1 261⁄211⁄2443⁄4866

1⁄283 2150

TPD 300 800 ONEA 300 800,000 5.7 970 776 554 911⁄214 11⁄4261⁄211⁄2443⁄410 661⁄283 2308

TPD 300 1000 ONEA 300 1,000,000 7.1 1212 970 693 911⁄214 11⁄4261⁄211⁄2443⁄410 661⁄283 2308 1⁄3HP - 5.5 Amp

TPD 300 1250 ONEA 300 1,250,000 8.9 1515 1212 866 911⁄214 11⁄4261⁄211⁄2443⁄412 661⁄283 2584

TPD 300 1500 ONEA 300 1,500,000 10.7 1818 1455 1039 911⁄214 11⁄2261⁄211⁄2443⁄412 811⁄283 2774 3⁄4HP - 10.2 Amp

TPD 400 600 ONEA 411 600,000 4.2 727 582 416 911⁄215 1 321⁄2255876

1⁄281 3207 1⁄4HP - 4.6 Amp

TPD 400 800 ONEA 411 800,000 5.7 970 776 554 911⁄215 11⁄4321⁄22551076

1⁄281 3212

TPD 400 1000 ONEA 411 1,000,000 7.1 1212 970 693 911⁄215 11⁄4321⁄22551076

1⁄281 3212 1⁄3HP - 5.5 Amp

TPD 400 1250 ONEA 411 1,250,000 8.9 1515 1212 866 911⁄215 11⁄4321⁄22551276

1⁄281 3212

TPD 400 1500 ONEA 397 1,500,000 10.7 1816 1455 1039 911⁄215 11⁄2321⁄22551291

1⁄281 3402

TPD 400 1750 ONEA 397 1,750,000 12.5 2121 1697 1212 911⁄215 2 321⁄22551491

1⁄281 3528 3⁄4HP - 10.2 Amp

TPD 400 2000 ONEA 397 2,000,000 14.2 2424 1939 1385 991⁄215 2 321⁄22551491

1⁄289 3669

TPD 500 2250 ONEA 495 2,250,000 16 2727 2182 1558 110 15 2 321⁄22551691

1⁄2100 4277 1 HP - 16 Amp

TPD 500 2500 ONEA 495 2,500,000 17.8 3030 2424 1732 110 15 2 321⁄22551691

1⁄2100 4419

TPD 600 720 ONEA 594 720,000 5.1 873 698 499 119 15 11⁄4321⁄22551076

1⁄2109 3667 1⁄4HP - 4.6 Amp

TPD 600 1000 ONEA 594 1,000,000 7.1 1212 970 693 119 15 11⁄4321⁄22551076

1⁄2109 3667

TPD 600 1250 ONEA 594 1,250,000 8.9 1515 1212 866 119 15 11⁄4321⁄22551276

1⁄2109 3667 1⁄3HP - 5.5 Amp

TPD 600 1500 ONEA 594 1,500,000 10.7 1816 1455 1039 119 15 11⁄2321⁄22551291

1⁄2109 3837

TPD 600 1750 ONEA 594 1,750,000 12.5 2121 1697 1212 119 15 2 321⁄22551491

1⁄2109 3837 3⁄4HP - 10.2 Amp

TPD 600 2000 ONEA 594 2,000,000 14.3 2424 1939 1385 119 15 2 321⁄22551491

1⁄2109 3837

TPD 600 2250 ONEA 575 2,250,000 16 2727 2182 1558 119 15 2 321⁄22551691

1⁄2109 4477 1 HP - 16 Amp

TPD 600 2500 ONEA 575 2,500,000 17.8 3030 2424 1732 119 15 2 321⁄22551691

1⁄2109 4619

TPD Power Dual Fuel Large Volume Commercial Water Heaters

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

SPECIFICATIONS

Certiﬁed Minimum Installation Clearances to Combustibles:

Front: 18 inches

Back: 0 inches

Sides: 0 inches

Top: 5 inches

A clearance of 24 inches should be maintained from

serviceable parts such as relief valve, power burner, drain

valve and anodes (anodes are located on side above cold

water inlet).

State Titan TPD models are Category I appliances

(Fan Assisted) and require a negative draft. These units

should only be commonly vented with other Category I

negative draft appliances per the latest addition of the

National Fuel Gas Code. An approved/listed Type “B” venting

material is recommended. A negative draft of -0.02˝ to -0.07

is required in the vent.

ASME

Large Volume Power Burner: Gas, Oil & Dual Fuel Commercial Water Heaters

Printed in U.S.A.

STPBGODF/1003

In keeping with our policy of continuous product improvement,

speciﬁcations are subject to change without prior notice.

COMMERCIAL

The Expert’s Choice®

500 Lindahl Parkway, Ashland City, TN 37015 • www.statewaterheaters.com

SUGGESTED SPECIFICATIONS

TITANTM LV POWER LOW NOX(MODELS TPX)

Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design

and include a powered gas burner with electronic ﬂame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure

regulator, diaphragm air switch for proof of blower operation, and ﬂame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input

rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall

be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, ASME stamped and listed

by Underwriters Laboratories. The water heater shall be approved for low NOx and meet or exceed California rule 1146.2. The unit shall provide modulating ﬁre for

smooth system operation and precise temperature control. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, modulating

control, combination temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door

shall be hinged for easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam

insulation. Heater(s) must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efﬁciency and standby loss. The outer jacket shall have a baked powder coat

ﬁnish. All internal surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel

by ﬁring at a temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty.

Professional start-up service to be included.

SUGGESTED SPECIFICATIONS

TITANTM LV POWER OIL AND DUAL FUEL (MODELS TPO AND TPD)

Water heater(s) shall be Model_____________________as manufactured by the State Water Heaters or an approved equal. Heater(s) shall have a minimum oil ﬁring

rate of_____gallons per hour, an input rating of____________BTU/HR. The heater(s) shall have a recovery rate of_____GPH at a 100°F rise and a storage capacity

of______gallons. The 160 psi design pressure tank shall be glass-lined with an alkaline borosilicate composition and fused to the steel by ﬁring at 1600°F. The heater(s)

shall be equipped with______NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, and carry a National Board stamping. The heater(s) shall be ASME and the

entire unit listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination

temperature and pressure gauge, low water cutoff, ASME rated temperature and pressure relief valve, and barometric draft regulator. Control compartment door shall

be hinged for easy access and include cam locks for security. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be

insulated with high-density foam insulation and meet or exceed current standard of ASHRAE 90.1-1999 for standby loss and recovery efﬁciency. The heater(s) shall

include a drain valve and ﬂame observation port. The jacket shall be baked powder coat ﬁnish. Heater(s) vessel shall have a 3, 5 or 10 year limited warranty against

failure as outlined in the written warranty.

The TPO models shall have a UL listed burner with two-stage pump, oil safety valve, electronic ﬂame safeguard, intermittent ignition and diaphragm air switch for proof

of ﬂame operation.

The TPD models shall include a dual fuel burner with two-stage oil pump, oil safety valve, electronic ﬂame safeguard, intermittent ignition, diaphragm air switch, main

and pilot automatic gas valves, gas pressure regulator and manual crossover switch.

SUGGESTED SPECIFICATIONS

TITANTM LV POWER GAS (MODELS TPG)

Water heater(s) shall be Model___________________as manufactured by State Water Heaters or an approved equal. Water heater(s) shall be of glass-lined design

and include a powered gas burner with electronic ﬂame safeguard, intermittent ignition, main and pilot automatic gas valves, redundant solenoid gas valve, gas pressure

regulator, diaphragm air switch for proof of blower operation, and ﬂame inspection port. Maximum supply gas pressure to heater 13˝ W.C. Heater(s) shall have an input

rating of ____________ and a recovery rating of ________ GPH at a temperature rise of 100°F with a minimum actual storage capacity of ________. Heater(s) shall

be equipped with _______ NPT water inlet and outlet openings, (2) 3˝ handhole cleanouts, shall have an ASME working pressure of 160 psi, and stamped National

Board, and listed by Underwriters Laboratories. Controls shall include: high temperature limit control (manual reset), upper and lower thermostats, combination

temperature and pressure gauge, low water cutoff, ASME rated temperature relief valve, drain valve and draft regulator. Control compartment door shall be hinged for

easy access. The heater(s) shall be equipped with multiple anodes for cathodic protection. The heater(s) shall be insulated with high-density foam insulation. Heater(s)

must meet or exceed current ASHRAE/IES 90.1-1999 for recovery efﬁciency and standby loss. The outer jacket shall have a baked powder coat ﬁnish. All internal

surfaces of the heater(s) exposed to water shall be glass-lined with an alkaline borosilicate, nickelous oxide composition that has been fused to steel by ﬁring at a

temperature range of 1400°F to 1600°F. Heater(s) tank shall have a 3, 5, or 10 year limited warranty against corrosion as outlined in the written warranty. Professional

start-up service to be included.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calentador de agua de State Water Heaters

State Water Heaters

State Water Heaters 200 Series Manual de usuario

State Water Heaters

State Water Heaters 100 SERIES Manual de usuario

State Water Heaters

State Water Heaters Sandblaster SBD30 150 NE Manual de usuario

State Water Heaters

State Water Heaters 300 Series Manual de usuario

State Water Heaters

State Water Heaters Standard Residential Cómo utilizar

State Water Heaters

State Water Heaters SHE50 76 Guía de aplicación

State Water Heaters

State Water Heaters SANDBLASTER CSB 120 Manual de usuario

State Water Heaters

State Water Heaters Select Dairy Barn SRESS00406 Manual de usuario

State Water Heaters

State Water Heaters PCE 30 20LSA Manual de usuario

State Water Heaters

State Water Heaters GS6 40 YBVIT, GS6 40 HBVIT, GS6 50 YBVIT, GS6 50 HBVIT, GS6 40 YBVIT 2, GS6 40 HBVIT 2, GS6 50 YBVIT 2, GS6 50 HBVIT... Manual de usuario

State Water Heaters

State Water Heaters SUF 119300 Cómo utilizar

State Water Heaters

State Water Heaters SBL 100 76NE Manual de usuario

State Water Heaters

State Water Heaters EN6-50-DORT 100 Hoja de información del producto

State Water Heaters

State Water Heaters SOF 85 220 G Manual

State Water Heaters

State Water Heaters FORCE 90TM Manual de usuario

State Water Heaters

State Water Heaters PREMIER Residential Gas Water Heaters Manual de usuario

State Water Heaters

State Water Heaters SBL95 199NE Manual de usuario

State Water Heaters

State Water Heaters GS6 40 YBVIT, GS6 40 HBVIT, GS6 50 YBVIT, GS6 50 HBVIT, GS6 40 YBVIT 2, GS6 40 HBVIT 2, GS6 50 YBVIT 2, GS6 50 HBVIT... Manual de usuario