StarTech.com PEXSATA24E Manual de usuario

PCI Express SATA Card

PEXSATA24E Instruction Manual

Actual product may vary from photo

4 port PCI Express SATA Card

FFCCCCCCoommpplliiaanncceeSSttaatteemmeenntt

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUsseeooffTTrraaddeemmaarrkkss,,RReeggiisstteerreeddTTrraaddeemmaarrkkss,,aannddootthheerrPPrrootteecctteeddNNaammeessaannddSSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other protected names

and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur

these references are for illustrative purposes only and do not represent an endorsement of a

product or service by StarTech.com, or an endorsement of the product(s) to which this manual

applies by the third-party company in question. Regardless of any direct acknowledgement

elsewhere in the body of this document, StarTech.com hereby acknowledges that all trademarks,

registered trademarks, service marks, and other protected names and/or symbols contained in this

manual and related documents are the property of their respective holders.

Instruction Manual

TTaabblleeooffCCoonntteennttss

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Hardware Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Windows VistaTM Fresh Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Windows 2000/XP/2003 Server Fresh Installation . . . . . . . . . . . . . . . .4

Installation without a Floppy Drive . . . . . . . . . . . . . . . .5

Windows 2000/XP/2003 Server/VistaTM Existing Installation . . . . . . . .5

Verifying successful installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Instruction Manual

Thank you for purchasing a StarTech.com 4 port PCI-E SATA Card. Now, you’ll be able

to maximize your computer SATA capability, while using only a single PCI-Express slot.

With four internal SATA ports, and two eSATA ports, you’ll be able to add the speed and

reliability of SATA to your internal storage, with the option of using an eSATA external

storage device.

IInnttrroodduuccttiioonn

•Provides four independent channels for support of up to four SATA drives

Features

System requirements

Package contents

•1 x Four-channel PCIe/SATA II adapter

This package should contain:

•Supports SATA II (300) drives and is backward compatible with SATA I (150) drives

•Features SATA II native command queuing (NCQ)

•Compliant with PCI Express Base Specification 1.0a

•A PC with an available PCI Express slot

•CD-ROM drive (driver installation)

•SATA-based drives

•1x Driver CD

•1x SATA Cable

•1x Instruction Manual (this document)

•Floppy Disk Drive (for third party driver installation)

Instruction Manual

HHaarrddwwaarreeGGuuiiddee

Please Note: There are six SATA ports available on PEXSATA24E, 4 internally and 2

eSATA connectors externally. Based on the images above, the respective ports have

been named A through F. Ports A to D are internal SATA ports, while ports E and F are

external SATA ports. By changing the jumper setting on PEXSATA24E circuit board, you

will be able to utilize four of the ports simultaneously. Please designate which ports you

wish to use, by adjusting jumper settings according to the chart below. By default, Port

A, B, C and D are working.

G (Jumper Settings)

JP Description Active Port

J2-J5 1-2 close Enable SATA Connector D

2-3 close Enable SATA Connector E

J6-J9 1-2 close Enable SATA Connector C

2-3 close Enable SATA Connector F

Instruction Manual

IInnssttaallllaattiioonn

WARNING! PCI Express cards, like all computer equipment, can be severely

damaged by static electricity. Be sure that you are properly grounded before

opening your computer case or touching your card. StarTech.com recommends

that you wear an anti-static strap when installing any computer component. If an

anti-static strap is unavailable, discharge yourself of any static electricity build-up

by touching a large grounded metal surface (such as the computer case) for

several seconds. Also be careful to handle the card by its edges and not the gold

connectors.

Please note: The following instructions assume that the SATA drives that will be

connected to PEXSATA24E have been physically installed within the computer

chassis. If this is not the case, and you require instruction on how to install the

hard drive in the computer chassis, please consult the documentation that

accompanied your purchase of the hard drive/computer.

Windows VistaTM Fresh Installation

Follow the instructions in this section if you are performing a new installation of Windows

VistaTM, and you wish to boot from a drive attached to PEXSATA24E:

1. Shut down all power connected to the computer, as well as all devices connected to

the computer peripherally (i.e. Printers, Monitors, Scanners etc.). As an added step to

ensure safe installation, unplug the power supply from the computer.

2. Remove the computer cover, allowing access to the motherboard and available slots.

For more detailed instruction on how to perform this step, please refer to the

documentation that was included with your computer at the time of purchase.

3. Locate an empty PCI Express slot, removing the metal bracket covering the

accompanying empty port/socket on the rear panel of the computer chassis.

4. Position the card above the open PCI Express slot, ensuring that the card is properly

aligned with the slot. Insert the card firmly into the slot, distributing force evenly across

the length of the board. Once inserted, secure the card into the adjoining socket

(previously covered by metal bracket, on the rear panel of the computer chassis), using

the correct size screw (if necessary, please consult documentation that accompanied

purchase of computer).

5. Attach PEXSATA24E to the Serial ATA drive, using a SATA (data) cable.

6. Repeat steps 4 and 5 for each remaining hard drive that will be connected (internally)

to PEXSATA24E.

7. Replace the computer cover and re-connect all power to the computer.

8. Start the computer as you normally would to perform an operating system installation,

ensuring that the Windows VistaTM installation CD/DVD is present in the drive, and the

BIOS has been suitably adjusted to boot from the CD/DVD Drive.9. When the

Windows Install screen appears, fill in the necessary information and click

Next. Follow the operating system instructions until a page appears asking “Where

Instruction Manual

do you want to install Windows?”. From here, click on Load Driver.

10. You will then be asked to provide the necessary driver files. The files can be

accessed by CD, DVD, or USB Flash Drive. As such, connect the drivers to the

computer using one of these methods, and click Browse to specify the location of the

files. Then, click Next.

11. Windows VistaTM will then install the necessary files, after which PEXSATA24E will be

recognized as a usable drive. Select the drive on which you wish to install the

operating system, and click Next, to resume normal operating system installation.

Follow the instructions in this section if you are performing a new installation of Windows

2000/XP/2003, and you wish to boot from a drive attached to PEXSATA24E.

Prior to installation, it is advisable to create a driver diskette. To do so, please locate the

following folder, located on the Driver CD:

D:\PCIe\4-SATA\Driver\i386 (where D: denotes the CD/DVD-ROM drive location)

Copy all files from this directory onto a blank floppy diskette. Remove the disk from the

drive, and label it accordingly.