StarTech.com UPOESPLT1G Manual de usuario
Manual Revision: 10/02/2018
User Manual
For the latest information and specications visit
www.startech.com/UPOESPLT1G
60W Ultra PoE Injector (Midspan) and Splitter Bundle
SKU#: UPOESPLT1G
Actual product may vary from photos
i
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Compliance Statements
FCC Compliance Statement
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at their own
expense.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
For the State of California
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
ii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Use of Trademarks, Registered Trademarks, and other
Protected Names and Symbols
This manual may make reference to trademarks, registered
trademarks, and other protected names and/or symbols of
third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes
only and do not represent an endorsement of a product or
service by StarTech.com, or an endorsement of the product(s)
to which this manual applies by the third-party company
in question. Regardless of any direct acknowledgement
elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks,
service marks, and other protected names and/or symbols
contained in this manual and related documents are the
property of their respective holders.
Warning Statements
Never use this product if parts are missing or damaged.
iii
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Safety Statements
Safety Measures
• Wiring terminations should not be made with the product and/or electric
lines under power.
• Product installation and/or mounting should be completed by a certied
professional as per the local safety and building code guidelines.
• Cables (including power and charging cables) should be placed and routed
to avoid creating electric, tripping or safety hazards.
Mesures de sécurité
• Les terminaisons de câblâge ne doivent pas être eectuées lorsque le produit
et/ou les câbles électriques sont sous tension.
• L’installation et/ou le montage du produit doit être réalisé par un
professionnel certié et dans le respect des normes locales et du code de
construction local.
• Les câbles (y compris les câbles d’alimentation et de chargement) doivent
être placés et acheminés de façon à éviter tout risque électrique, de chute ou
de sécurité
安全対策
• 電源が入っている状態の製品または電線の終端処理を行わないでください。
• 製品の設置やマウントは、使用地域の安全ガイドラインおよび建築基準に従い、有資格の専門業者が行うようにしてください。
• ケーブル（電源ケーブルと充電ケーブルを含む）は、適切な配置と引き回しを行い、電気障害やつまづきの危険性など、安全上のリスクを回避するよう
にしてください。
Misure di sicurezza
• I terminiali dei li elettrici non devono essere realizzate con il prodotto e/o le
linee elettriche sotto tensione.
• L’installazione e/o il montaggio dei prodotti devono essere eseguiti da un
tecnico professionale certicato che conosca le linee guida locali sulle norme
edilizie e sulla sicurezza.
• I cavi (inclusi i cavi di alimentazione e di ricarica) devono essere posizionati
e stesi in modo da evitare pericoli di inciampo, rischi di scosse elettriche o
pericoli per la sicurezza.
Säkerhetsåtgärder
• Montering av kabelavslutningar får inte göras när produkten och/eller
elledningarna är strömförda.
• Installation och/eller montering får endast göras av behöriga yrkespersoner
och enligt gällande lokala förordningar för säkerhet och byggnormer.
• Kablar (inklusive elkablar och laddningskablar) ska dras och placeras på så
sätt att risk för snubblingsolyckor och andra olyckor kan undvikas.
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Table of Contents
Compliance Statements........................................................................i
Warning Statements ..............................................................................ii
Safety Statements..................................................................................iii
Product Diagram ....................................................................................1
Splitter .......................................................................................................................................................... 1
Injector ......................................................................................................................................................... 2
Product Information ..............................................................................4
Package Contents ..................................................................................................................................... 4
Requirements .........................................................................................5
Installation ..............................................................................................5
Connecting the Splitter to the Injector............................................................................................. 5
Connecting the Splitter Only................................................................................................................ 6
Connecting the Injector Only .............................................................................................................. 7
Operation ................................................................................................8
LED Indicators............................................................................................................................................. 8
Switches........................................................................................................................................................ 9
1
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Product Diagram
Splitter
Top View
Input Side View
PoE Input
Port
Power LED
Indicators
2
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Output Side View
Injector
Top View
DC Output
DIP Switch
Ethernet
Data Port
DC Output
Power Port
Power LED
Indicators
3
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Input Side View
Output Side View
DC Power
Input Port
Ethernet
Data Port
PoE Output
Port
PoE Usage
LED
Indicators
4
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Switch Side View
Product Information
Package Contents
• PoE Splitter x 1
• PoE Injector x 1
• Universal Power Adapter x 1
• Power Cords (NA/JP, UK, EU, AU) x 4
• DC Plug Cable x 2
• RJ45 Network Cable x 1
• User Manual x 1
PoE Mode
Switch
5
To view manuals, videos, drivers, downloads, technical drawings, and more visit www.startech.com/support
Requirements
For the latest requirements, please visit
www.startech.com/UPOESPLT1G.
Power:
• Available AC Electrical Outlet
Splitter
• Network Device x 1
• Ethernet Cable x 1
Injector
• Network Device x 1
• Ethernet Cable x 2
Installation
Connecting the Splitter to the Injector
Connecting the Injector
1. Toggle the PoE Mode Switch to Standard Mode. See Legacy
for details regarding special applications that require Legacy
Mode to be enabled.
2. Connect an Ethernet Cable to your Network Device.
3. Connect the other end of the Ethernet Cable to the Ethernet
Data Port on the Injector.
4. Connect the Universal Power Adapter to the DC Power Input
Port on the Injector.
5. Connect the other end of the Universal Power Adapter to an
AC Electrical Outlet.
Tabla de contenidos
Otros manuales de Equipo de laboratorio de StarTech.com
StarTech.com
StarTech.com AS445C-POE-INJECTOR Manual de usuario
StarTech.com
StarTech.com POEINJ1G Manual de usuario
StarTech.com
StarTech.com POEINJ30W Manual de usuario
StarTech.com
StarTech.com POEINJ1G90W Manual de usuario
StarTech.com
StarTech.com POEINJ1GI Manual de usuario
StarTech.com
StarTech.com POEINJ4G Manual de usuario
Manuales populares de Equipo de laboratorio de otras marcas
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manual de usuario
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manual de usuario
NI
NI PXI-5422 Manual
Collomix
Collomix Aqix Manual de usuario
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario
Ocean Insight
Ocean Insight FLAME-NIR+ Manual de usuario
