StarTech.com USB3SSATAIDE Manual de usuario

Manual Revision: 04/16/2013

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

USB3SSATAIDE

USB 3.0 to SATA or IDE Hard Drive Adapter Converter

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Introduction ............................................................................................1

Packaging Contents ................................................................................................................................. 1

System Requirements .............................................................................................................................. 1

Hard Drive Adapter ................................................................................................................................... 2

Power Adapter ........................................................................................................................................... 2

Installation ..............................................................................................3

Hardware Installation .............................................................................................................................. 3

Driver Installation ...................................................................................................................................... 6

Specications ..........................................................................................7

Technical Support ..................................................................................8

Warranty Information ............................................................................8

Instruction Manual

Introduction

Packaging Contents

• 1x USB 3.0 to SATA/IDE converter

• 1x SATA Cable

• 3x AC Power Cord (NA/UK/EU)

• 1x Power Supply

• 1x Driver CD

• 1x Instruction Manual

System Requirements

• Available USB 3.0 port

• Available AC electrical outlet

• Windows 2000/XP/Server 2003/Vista/ Server 2008 R2/7/8 (32/64-bit)

Instruction Manual

Hard Drive Adapter

Power Adapter

Instruction Manual

Installation

WARNING:

• Do not disconnect any cables or power sources while the connected hard drive(s)

is/are active. This can result in data loss and possible damage to the hard drive.

To avoid this, please follow the steps outlined in the section entitled Removing

Connected Drives.

• Please ensure that the hard drive(s) has(have) been connected to the adapter prior

to connecting the adapter to the host computer.

Hardware Installation

1. Ensure the mini-switches on the power adapter are

set to the OFF position.

2. Insert the dual-cylinder connector provided by the

main power cord into the corresponding port on

the power adapter brick.

3. (OPTIONAL) Connect the small, cylindrical power connector (splits o from LP4

connector) provided by the Switching Power Adapter to the corresponding power

port on the Hard Drive Adapter. This is only required if the Hard Drive Adapter

cannot draw enough power directly from the USB port.

4. Connect the remaining connector of the assembled power adapter to an available

wall outlet or power bar.

Connect the Drive(s) to the Hard Drive Adapter

WARNING! Hard drives and storage enclosures require careful handling, especially

when being transported. If you are not careful with your hard disk, lost data may

result. Always handle your hard drive and storage device with caution. Be sure that

you are properly grounded by wearing an anti-static strap when handling computer

components or discharge yourself of any static electricity build-up by touching a large

grounded metal surface (such as the computer case) for several seconds.

NOTE: if you are using two IDE hard drives concurrently, one of the drives must be set to

act as a Master drive, and the other as slave. If you are using a 3.5” IDE drive and a SATA

drive together, the IDE drive must be set to act as a Slave drive. For further information

on this, please consult the documentation that accompanied the hard drive(s) at the

time of purchase.

Instruction Manual

SATA Drive

1. Insert one connector provided by a SATA data cable, into the SATA port on the Hard

Drive Adapter.

2. Insert the remaining connector provided by the SATA data cable, into the SATA data

port on the SATA hard drive.

40/44-pin IDE Drive

1. Align the IDE drive interface on the hard drive with the appropriate port provided

by the hard drive adapter.

2. Gently, but rmly insert the IDE Connector (provided by the adapter) into the port

on the rear panel of the hard drive. Ensure the drive is connected snugly.

Instruction Manual

Connect the Drive(s) to the Power Adapter

WARNING! When connecting the hard drive to the Power Adapter, please ensure that

the mini-switches (located on the main power switch) are set to the OFF position, prior

to establishing a connection. Failure to do so could result in damage to the drive, or an

electrical shock to the user.

SATA Drive

Insert the SATA power connector provided by the power adapter into the SATA power

port on the rear panel of the SATA hard drive.

40-pin IDE Drive

Insert the LP4 power connector provided by the power adapter into the LP4 power

port on the rear panel of the IDE hard drive.

Connect the Hard Drive Adapter to the Host Computer

1. Insert the USB connector into an available USB port on the host computer. Move the

mini-switch on the Hard Drive Adapter Power Switch to the ON position, to enable

the selected drives.

2. The operating system will detect the connected adapter, and prepare the drives for

use. If a new/blank drive, it may need to be formatted before it can be used. Please

consult the documentation for the operating system for details.

Instruction Manual

Removing Connected Drives

WARNING! Do not remove a connected hard drive while the drive is in use. To prevent

data loss or damage to the drive(s), please follow the instructions below.

Removing a connected drive safely requires that the drive not be in use. To ensure that

this is the case, you can remove the drive in one of the two following ways:

1. Click on the Safely Remove Hardware icon, in the taskbar, and select Safely Remove

USB Mass Storage Device.

2. Following this, you will be notied that it is safe to remove the USB Mass Storage

device:

If you do not wish to use the Safely Remove Hardware Wizard:

1. Power down the host computer. Once the computer has been turned o, it is safe

to remove the connected drive(s): Move the mini-switch on the power adapter that

corresponds with the drive you wish to remove to the OFF position.

Driver Installation

No driver installation is required for the supported operating systems, as the drivers

are already installed.

Instruction Manual

Specications

Host Interface USB 3.0

External Connectors

1 x 15 pin SATA Power female

1 x 4 pin Power (LP4) Female

1 x 40 pin IDE Female

1 x 44 pin IDE Female

1 x 7 pin SATA Data male

1 x USB type A male

LEDs

1 x USB Link

1 x IDE Detect/Activity

1 x SATA Detect/Activity

Maximum Data Transfer Rate USB 3.0: 5Gbps

Power Adapter 12VDC, 2000mA

Compatible Operating Systems Windows 2000/XP/Server 2003/Vista/

Server 2008 R2/7/8 (32/64-bit)

Tabla de contenidos

Otros manuales de Adaptador de StarTech.com

StarTech.com

StarTech.com USB2DVI Manual de usuario

StarTech.com

StarTech.com SLMPT2VGA Manual de usuario

StarTech.com

StarTech.com US2GA30 Manual de usuario

StarTech.com

StarTech.com S322M225R Manual de usuario

StarTech.com

StarTech.com USB312SAT3CB Manual de usuario

StarTech.com

StarTech.com CDP2HD4K60SA Manual de usuario

StarTech.com

StarTech.com USB867WAC22 Manual de usuario

StarTech.com

StarTech.com USB2HDMI Manual de usuario

StarTech.com

StarTech.com S322SAT3R Manual de usuario

StarTech.com

StarTech.com MPEXUSB3S2 Manual de usuario

StarTech.com

StarTech.com CBUSB22 Manual de usuario

StarTech.com

StarTech.com SATA35252X Manual de usuario

StarTech.com

StarTech.com PCI330USB2 Manual de usuario

StarTech.com

StarTech.com DKT31CVHPD3 Manual de usuario

StarTech.com

StarTech.com DVI2HD Manual de usuario

StarTech.com

StarTech.com USB2PS2 Manual de usuario

StarTech.com

StarTech.com PEX1PCI1 Manual de usuario

StarTech.com

StarTech.com MDP2HDMIUSBA Manual de usuario

StarTech.com

StarTech.com USB300WN2X2D Manual del sistema

StarTech.com

StarTech.com SAT2M2NGFF25 Manual de usuario

StarTech.com

StarTech.com MPEX2S952 Manual de usuario

StarTech.com

StarTech.com MSDREADU3CA Manual de usuario

StarTech.com

StarTech.com USB32DPPRO Manual de usuario

StarTech.com

StarTech.com MHD2HDF11 Manual de usuario

Manuales populares de Adaptador de otras marcas

PCB Piezotronics

PCB Piezotronics 090B274 Manual de usuario

Auvidea

Auvidea J20 Manual del producto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manual de usuario

Akribis

Akribis ITF-21-BISS-MIT Manual de usuario

Tenda

Tenda W54U Manual de usuario

ROHO

ROHO AGILITY Manual de usuario

PROLiNK

PROLiNK WN2001 Manual de usuario

Hawking

Hawking HUF2 Manual de usuario

Airlink101

Airlink101 AWLC4030 Manual de usuario

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manual de usuario

Philips

Philips SWA4554S/10 Manual de usuario

JVC

JVC TS-C9D2B Manual de instrucciones

NETGEAR

NETGEAR A6100 Manual de usuario

D-Link

D-Link DWA-121 Manual de usuario

Philips

Philips SWA2037 Manual de usuario

Basalte

Basalte 0610-20 Manual de usuario

Yealink

Yealink EHS40 Manual de usuario

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manual de usuario