StarPanel Technologies M3104 Manual de usuario

M3104

Industrial Touch Screen Monitor

User and Calibration Manual

Rev. G (6/09

)

Displays for the Real World



StarPanel Technologies, Inc.

(503) 654

6216

mail: support@starpanel.com

StarPanel Technologies, Inc.

All products or brand names are trademarks or registered trademarks of their respective companies.

The information contained in this manual is subject to change without notice.

Document

contains information for StarPanel M3104 monitor.

Printed in the USA

COMPLIANCE STATEMENT

Note: This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in

accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his own expense.

his Class A digital apparatus complies with Canadian ICES

003.

Cet appareil numériqué de la classe A est conformé à la norme NMB

003 du

Canada.

Table of Contents

Welcome to the M3104

Industrial Touch Screen Mo

nitor

................................

.............

Connecting to the M3104 Monitor

................................

................

Power

................................

......................

VGA

................................

.........................

Serial

................................

.......................

General Specifications and System Require

ments

................................

......................

Adjustments & Calibration

................................

..............................

Using The Control Buttons

................................

...........................

Maintenance and Care

................................

.....

Backlight

................................

..................

Cleanin

................................

..................

Energy Saving Mode

................................

........

Energy Saving Mode

................................

....

Touch Screen

................................

...................

Service Guide

................................

...................

Technical Support

................................

............

StarPanel Technologies, Inc. Limited Product Warranty

................................

.............

M3104 Industrial Touch Screen Monitor

Welcome to the M3104

Industrial Touch Screen Monitor

Thank you for purchasing the M3104

Industrial Touch Screen Monitor

. This manual contains

inf

ormation and instructions for the monitor. Please refer to it if you have questions about

the monitor.

Connecting to the M3104 Monitor

There are three input/output connections to the M3104 monitor: power, serial and video.

See

figure below.

Power

ur M3104 monitor is powered by connecting a 2.5mm circular jack to a 12Vdc @ 1.5A power

supply or greater must be used.

Video

The video (DB15HD) connection is made by connecting a video cable between the monitor and

the video source connector on the PC.

Serial

The serial (DB9) connector is provided for touch screen communication. A serial cable from this

connector to the appropriate COM port on the PC that has been setup in the touch driver

installation is necessary for the touch function to operate.

M3104 Industrial Touch Screen Monitor

General Specifications and System Requirements

Physical

Enclosure:

Black powder coated aluminum front bezel

Yellow chromate aluminum rear cover

Sealing:

NEMA 4/12 properly mounted w/ sealing gasket

Weight:

3.5

lb.

Connec

tors:

15HD Female (video interface)

9, Female (serial interface)

RAPC 712, Male 2.5mm (12VDC power)

Viewing Area:

8.31 x 6.23 inches

Display Size:

10.4 inch (diagonal)

Electrical

Voltage:

12VDC ±10%, 100mV Ripple

Current Range:

1A nominal

Functional

Display Type:

Active Matrix TFT Color LCD

Colors:

262,144

Display Modes:

VGA, EGA, CGA with automatic mode detect

Resolution:

640x480 Pixels in VGA mode, will also support CGA and EGA

modes

Frequency:

31.5 kHz Horizontal Typ., 60 to 75 Hz V

ertical Rate

Interface:

Standard analog VGA

Signals:

R G B, HSYNC and VSYNC

OSD:

MENU, SEL, UP, DOWN

Environmental

Temperature:

Operating 0



C to +50



C; Non

Operating



C to +60



Shock:

30G, half sine, 11ms, 3 times per axis, non

operating

Vibrat

ion:

10Hz to 500Hz @ 1.5G

Humidity:

95% Non

condensing

The M3104 monitor supports CGA, EGA and VGA compliant video input which complies with the input

specification. The vertical refresh rate has a maximum supported frequency of 75 Hz. Many VGA sources

can

operate at much higher refresh rates and, for CRT monitors, the higher the refresh the more flicker

free the

display. On the M3104 monitor, the refresh rate doesn't determine display quality. Most video sources offer

multiple refresh rates. The typic

al VGA (640x480) refresh rate is 60 Hz.

M3104 Industrial Touch Screen Monitor

Adjustments & Calibration

Due to variations in operating environments, user preferences, and hardware, the M3104 is provided with control

buttons that allow the user to adjust the settings of the monitor.

Using The C

ontrol Buttons

The monitor has four control buttons and a power on/off button on the rear of the monitor which allow the user to

make adjustments. See figure below.

The On Screen Display (OSD) will open when the MENU button is pressed. Use the SEL and UP

DOWN buttons

to select and set the desired calibration mode. Press the MENU button to step back in the menu. The monitor will

return to normal operation (exit OSD) if no buttons are pressed after a period of time.

Quick Set Buttons

Auto adjustment (Pre

ss SEL)

The monitor will run a short routine to set various calibration modes automatically when the SEL button is pressed

in normal operation (no OSD screen active)

M3104 Industrial Touch Screen Monitor

Maintenance and Care

The M3104 has been designed for demanding applications and theref

ore requires little

maintenance.

Reasonable care should be taken when connecting or removing the interface cables so that the

connector pins are not damaged. This is same care that is required for any computer or monitor.

Backlight

During the life of t

he monitor, the fluorescent backlight may need to be replaced. The normal life

of the tubes is 25,000 hours minimum.

Cleaning

For best results, use a clean non

abrasive cloth towel dampened with mild soapy water to clean

all external surfaces of the mon

itor.

For the viewing area, use a clean non

abrasive cloth towel dampened with commercially available

window cleaners or mild soapy water.

M3104 Industrial Touch Screen Monitor

Energy Saving Mode

When the M3104 monitor is connected to an energy saving compatible computer,

the monitor will

comply with the control signals to power down the monitor into a lower power state.

Caution: The power saving function will automatically put the monitor into active

off state if you

turn on the monitor and leave the rest of the system

off. However, once the monitor can sense

the horizontal and vertical sync’s, it will automatically return to its normal operation state.

M3104 Industrial Touch Screen Monitor

Touch Screen

The

M3104

Industrial Touch Screen Monitor

is provided with an integrated touch screen overlay.

The tou

ch screen is activated by connecting the seria

l port of the M3104

monitor with the serial

port of the PC. You must also install the drivers for the operating system you are using. These

drivers are available as download zip files from the support page of

the StarPanel web site.

http://www.starpanel.com/support/FTPLinkPage.html#Downloads

After installing the appropriate driver you will need to set it for the monitor touch parameters listed

below.

Touch Driver Installation Options

Note:

When installing

touch drivers the configuration for the monitor is

TSHARC

and

the baud rate is

9600

Tabla de contenidos

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación