Stark 58108 Manual de instrucciones original
OWNER’S MANUAL AND SAFETY INSTRUCTIONS
WALKIE ELECTRIC TRUCK PALLET
ITEM # 58108
SAVE THIS MANUAL. KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY,
OPERATION, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES. WRITE THE PRODUCT’S
SERIAL NUMBER ON THE BACK OF THE MANUAL, OR THE MONTH AND YEAR OF PURCHASE IF
PRODUCT HAS NO SERIAL NUMBER
FOR QUESTIONS, PLEASE CALL CUSTOMER SERVICE: 909.628.4900
SAFETY WARNINGS
Read all safety warnings and instructions. Failure to follow the warnings and
instructions may result in injury and/or property damage. Save all warnings
and instructions for future reference.
The warning and safety instructions in this manual are not meant to cover all possible conditions
and situations that may occur. Common sense, caution and care must be exercised when
operating or cleaning tools and equipment. Always contact your dealer, distributor, service
agent or manufacturer about problems or conditions you do not understand before operating
the product.
SAVE THESE WARNINGS.
1
• DO NOT operate pallet truck on inclined surfaces. It must be used on level surfaces only. Unanticipated
motion will occur as soon as the pallet truck lifts a load from surface.
• DO NOT overload the Pallet Truck beyond the load rating (3000lbs per unit).
• DO NOT start the vehicle’s engine, or drive with Jack in use. Jacks are designed for hand maneuvering
of vehicles only.
• DO NOT operate the pallet truck in temperatures above 104 °F or under 41 °F.
• DO NOTattempt to push the pallet truck over obstacles. They are designed to be used on level and
reasonable smooth surfaces only.
•During operation and lifting, the load must be centered on the pallet jack.
•Operating altitude should not exceed 1200 meters.
•DO NOT operate the pallet truck in corrosive environments such as near ammable and/or explosives.
•This is a tramp type electric pallet truck with autonomous control, lifting and lowering that is controlled
by the handle button. Improper operation of the pallet truck can damage the machine.
•Lifting or carrying people is strictly prohibitied.
• DO NOT use the pallet truck for anything other than the purposes set forth by the manufacturer.
• DO NOT modify or alter the pallet jack.
•DO NOT use the pallet truck on lifting or loading ramps.
•Make sure there is adequate lighting when operating the pallet truck.
•DO NOToperate the machine beyong the rated capacity. Read all labels and nameplates before
operating the machine.
SAFETY WARNINGS PRODUCT INFORMATION
SAVE THESE WARNINGS.
1 2
PRODUCT INFORMATION
3
PARTS INFORMATION / OPERATION
HANDLEBAR ASSEMBLY
Lifting point
STEP 1: Use a lifting machine to lift the car from the packing box an place it in position.
Note: Pay attention to the lifting point (shown above). In order to avoid scratches, a mat should
be placed on the ground, under the unit.
4
5
STEP 2: Take out the handle assembly, battery and manual from the box.
6
STEP 3: Use the tooling to disassemble the elastic cylindrical pin and small shaft (see the
red arrows in the picture above) and set them aside for later use.
7
STEP 4: Put the handlebar assembly into the handle seat. Then insert the chain into the
small hole at the end of the handle and clamp the bolt at the bottom end of the chain into
the U-shaped part of the lowering pedal. Then put the small shaft into the fixing hole and
install the cylindrical pin.
8
STEP 5: After removing the screws on the left side of the motor cover, assemble the
wires on the handle and the other end under the motor cover. Install the motor cover in
place and fix it with screws. Insert the battery into the battery slot, then after the
connection is complete, turn on the key switch and turn it on.
PARTS INFORMATION / OPERATION
9
1. Falling Knob 2. Driving Button 3. Lifting Button 4. Emergency Reverse 5. Horn 6. Electricity Meter
7. Falling Button 8. Slow Speed Button
BRAKING
• Turn the travel switch (2) to "0" position or release the switch to make the truck brake until it stops.
• With the driving switch (2) moving directly from one driving direction to the opposite direction, the vehicle
regenerates the brake until it begins to move in the opposite direction.
• The handle moves up and down to the braking area (' B ') and the truck brakes. If the handle is released, the
handle automatically moves to the upper braking area (' B ') and the truck start braking until it stops.
• Emergency Reverse button (4) can prevent the operator will be squeezed, when the truck is facing an
obstacle in forward direction. The body touch Emergency reverse button and the truck de-accelerates or
starts to move to (BW) for a distance and then stops. If the handle is in the operating area and the truck is not
moving, please consider that this button is still working.
Tabla de contenidos
