Star SCD122U Manual de usuario
Customer Display
SCD122U
Hardware Manual
– i –
Federal Communications Commission
Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable.
This statement will be applied only for the equipments marketed in U.S.A.
Statement of
The Canadian Department of Communications
Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le
ministère des Communications du Canada.
The above statement applies only to equipments marketed in Canada.
Trademark acknowledgments
SCD122U: Star Micronics Co., Ltd.
Notice
• All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s
express permission is forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to
press. However, should any errors be detected, STAR would greatly appreciate being informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 2008 Star Micronics Co., LTD.
– ii –
Safety Precautions
This document uses the two headings shown below to call attention to potential hazards. Failure to observe the
information provided under or alongside these headings may lead to injury or damage to your system. Be sure that
you understand the meaning of each heading before you proceed.
WARNING
3Indicates a potentially lethal hazard. Failure to observe a WARNING may result in
severe injury or death.
CAUTION
3Failure to observe a CAUTION may result in personal injury, or in damage to equip-
ment or other property.
WARNING
3Shut down your equipment immediately if it produces smoke, a strange odor, or unusual
noise. Continued use may lead to re. Immediately turn the power off and contact your
dealer or a Star service center for advice.
3Never attempt to repair this product yourself. Improper repair work can be dangerous.
Tampering with this product may result in injury or re.
3Never disassemble or modify this product. Tampering with this product may result in
injury or re.
3Do not allow foreign matter to fall into the equipment. Penetration of foreign objects
may lead to re.
3Be sure to connect the USB port.
3If water or other liquid spills into this equipment, pull out the USB cable immediately
and contact your dealer or a Star service center for advice. Continued usage may lead
to re. To adjust the angle of the display unit, be sure to hold it by its support pillar.
3Hold it by its support pillar to adjust the angle of the display unit.
– iii –
CAUTION
3Do not use in locations subject to high humidity or dust levels.
Excessive humidity and dust may cause equipment damage, re, or shock.
3Do not place heavy objects on top of this product. Never stand or lean on this prod-
uct.
Equipment may fall or collapse, causing breakage and possible injury.
3Do not plug in the cables differently from the instructions in the manual.
Wrong connection may cause equipment damage and re.
3Hold the plug when pulling out the cable.
3Do not use this product near the device generating electric noises.
3Do not put heavy objects on the cable, and bend it heavily.
3Do not come closer to the display.
3Do not use this product in the dark.
TABLE OF CONTENTS
1. Unpacking.................................................................................................................................................1
1-1. Unpacking ....................................................................................................................................1
2. Installation Examples ..............................................................................................................................2
2-1. Selecting a Base Stand .................................................................................................................2
2-2. Combinations of Support Pillars..................................................................................................2
3. Setting Up .................................................................................................................................................3
3-1. Using the Surface-Mount Stand...................................................................................................3
3-2. Installing Support Pillars..............................................................................................................4
3-3. Using the Fixed-Mount Stand......................................................................................................6
3-4. Installing the Software .................................................................................................................7
4. Setting the DIP Switch.............................................................................................................................8
5. Specifications ..........................................................................................................................................10
5-1. General Specifications ...............................................................................................................10
6. Character Code List ..............................................................................................................................12
6-1. International Character Set List .................................................................................................12
6-2. Character Code Table.................................................................................................................12
Please access the following URL
http://www.star-m.jp/eng/dl/dl02.htm
for the latest revision of the manual.
– 1 –
1. Unpacking
1-1. Unpacking
After unpacking the unit, check that all the necessary accessories are included in the package.
If anything is missing, contact the dealer where you bought the equipment and ask them to
supply the missing part. Note that it is a good idea to keep the original box and all the packing
materials just in case you need to pack the equipment up again and send it somewhere at a later
Display (1 unit)
Stand (2 items) Stand Plate (2 units)
Extension Support
(3 pieces)
Screw (4 pieces)
Nut (3 pieces)
Washer (6 pieces)
CD-ROM
( 1 piece )
Safty Instruction Sheet
( 1 piece )
Rubber Foot (2 pieces)
Pillar A
Pillar B
Pillar C
Screw
(4 pieces)
Screw
(4 pieces)
Screw Bag
– 2 –
2. Installation Examples
This customer display consists of three pieces: the display unit, support pillar, and base stand.
For the base stand, two choices are available: a surface-mount stand that can be moved freely,
and a xed-mount stand that is screwed onto a table or the like.
To bring the display unit to an appropriate viewing height, the supplied support pillars can be
combined to attain four different heights.
2-1. Selecting a Base Stand
Surface-mount stand example Fixed-mount stand example
2-2. Combinations of Support Pillars
Surface-mount stand example
Fixed-mount stand example
Table
– 3 –
3. Setting Up
3-1. Using the Surface-Mount Stand
1) Route the USB interface cable through the surface-mount stand.
2) Insert the stem of the display unit into the surface-mount stand until it clicks into place.
3) Pull the USB interface cable out of the cutout in the surface-mount stand as shown below.
4) Attach the stand plate to the surface-mount position of the surface-mount stand, and tighten
it with four screws.
5) Connect the USB interface cable into the USB port of the host computer.
Note: The rubber feet come already afxed to the stand plate. In addition, two rubber feet
are supplied with the unit. They are spares to be used if the existing ones become
detached.
Screw
Stand plate
Surface-mount stand
Rubber foot
– 4 –
3-2. Installing Support Pillars
To use only one of the support pillars, install support pillar C.
To use two of them, install support pillars B and C. To use three of them, install support pillars
A, B, and C.
3-2-1. Using One Support Pillar
1) Route the USB interface cable through support pillar A, and insert the stem of the display
unit into support pillar A.
2) Insert support pillar A into the surface-mount stand until it clicks into place.
Support pillar A Support pillar ASupport pillar B
Support pillar B
Support pillar C
Support pillar C
Support pillar A
Support pillar A Support pillar CSupport pillar B
– 5 –
3-2-2. Using Two Support Pillars
1) Route the USB interface cable through support pillar C, and insert the stem of the display
unit into support pillar C.
2) Insert support pillar B into support pillar C until it clicks into place.
3) Insert support pillar B into the surface-mount stand until it clicks into place.
3-2-3. Using Three Support Pillars
1) Route the USB interface cable through support pillar C, and insert the stem of the display
unit into support pillar C.
2) Insert support pillar B into support pillar C until it clicks into place.
3) Insert support pillar C into support pillar A until it clicks into place.
4) Insert support pillar C into the surface-mount stand until it clicks into place.
CAUTION
The USB interface cable has sufcient length to accommodate the maximum length of the sup-
port pillar with all the pieces connected. If fewer pieces are used for the support pillar, there
will be some slack in the cable. If you push the extra length of the cable into the support pillar
to take up the slack, make sure the cable moves freely.
As the display unit is turned, it pulls on the cable. Thus, if the display unit is turned while the
cable is tucked tightly into the support pillar, it can apply undue force on the connector and lead
to a contact failure. Therefore, do not tuck the cable tightly into the support pillar.
Support pillar BSupport pillar C
Support pillar BSupport pillar C
Support pillar A
Tabla de contenidos
