Stanley BXGT10147E Instrucciones de instalación y funcionamiento

Automatic.Hose.Reel.

Installation, Use, and

Maintenance Guide

Unpacking

Please.check.the.contents.of.your.package

A, Instruction.Manual

B, Hardware.Pack

C, Hose.Reel

D, Wall.Bracket

E, Mount tube

Caution: This.hose.reel.is.not.intended.to

be.used.as.a.potable.water.source

Caution: Except.as.indicated.in.these

instruction.do.not.open.the.outer.housing

Hardware.Pack

Contents

Couplings

Your hose reel was made with one of

The following hose-end configurations

Poly quick-connect

with nozzle

Preparing.your.tools

Installation.is.easier.with.the.right.tools…

electric drill

3/8”masonry drill bit

1/8”drill bit

pen or pencil

bubble level

adjustable wrench

Philips screwdriver

tape measure

B.1 X 4

Choosing the best location

Select the best location to mount your hose reel

1, Near your worksite. Your hose reel comes with up to 10-30m (30-100ft) of

hose, Think about where you need to water and make sure the hose can reach.

2. Near a spigot. This hose reel is provided with a 1-2m (3-6.5ft) leader hose, so

selection a location close to the spigot

3. On a sturdy wall or structure. There are many options for mounting this hose

reel into various structures, but it’s important that the structure be sturdy enough

to support the weight of the reel, up to 14.5kg(32lbs) with water

4. In the shade. By mounting your hose reel in a shady area of your yard, you

can reduce harmful effects of sunlight on the reel and hose and extend the life of

your purchase.

Installation:Heavy plywood cladding

If you wall’s ply wood cladding is thick, 12mm (1/2”) or more, you can directly

mount the Wall Bracket

WARNING: Ensure there are no live electrical wires or

Plumbing in the wall at the location you are drilling

CAUTION: when using powder tools such as a

electric drill, please wear eye protection.

‘

READING: please check which mold you have, and then

get the installation dimension from the table below.

1, The mounting bracket has 4 holes which will be used to secure it to the wall or timber

post. Use the mounting bracket as a template to mark the holes prior to drilling (Note: Use

a level to ensure the holes are vertically aligned).

2, Drill the required holes with a 10mm(3/8”) masonry drill bit (for wall mount)

approximately 50mm(2)”deep or a 3mm(1/0") drill bit (for timber post) approximately

60mm(2.5") deep.

3, Once the holes are drilled, insert the anchor plug (provided) into each hole (applicable

for wall mount).

4, Fasten the mounting bracket with four screws and washer (provided .B.1 or B.2) to the

wall or timber post

5, Hag Hose Reel (C) on wall bracket (D), and secure it by inserting the mount

tube.(provided E)

6, Connect the leader hose to water source.

Model number

Hardware pack

BXGT10147E

57mm(2-1/4”)

165mm(6-1/2”)

B.1

Operating Instructions

Extending the hose

1, Pull the hose out to the desired length. The hose will automatically lock in position

Anywhere lock: Pull out the hose to the desired length and then stop pulling so the reel can lock in the desired position.

2, To retract, pull out about 300mm of hose; the hose will retract back into the reel

Caution: Always hold the hose until it

completely. retract into the hose reel

Caution: The yellow tape marks the end

of the hose length.

Noted :

1, To retract, it is suggested that a minimum of 15”has been extended

2, During retraction, always hold on to the hose and follow the retraction until it is finished. Under no circumstances should

you let go of the hose as it will retract at a high speed potentially causing injury to any person standing nearby, and/or

damaging to the hose and hose reel.

3, When the hose is twisted, it is necessary to extend the hose to its full length, untwist the hose and then allow it to retract

Adjusting the stop-ball

The location of the stop ball can be adjusted to allow more or less hose exposed when fully rewound.

1, Pull out the hose to the desired length, ensuring the hose reel is locked ( will not rewind).

2, Loose two screws in the stop ball and move it to the desired location.

3, And tight screws in the desired location.

4, Unlock the hose

Caution: Always make sure the hose reel is locked before removing the stop ball, and make

sure the stop-ball is securely fastened before unlocking the reel.

Care and Maintenance Tips

1, Turn off the water source and release the pressure in the hose when not in use.

2, To prevent freezing and potential damage to the hose reel, store indoors during winter months.

4, Clean the housing and hose using only mild soap and water.

Tabla de contenidos

Otros manuales de Herramientas de Stanley

Stanley

Stanley 150 Manual de usuario

Stanley

Stanley CH1513101 Manual de usuario

Stanley

Stanley 70500 Guía de solución de problemas

Stanley

Stanley TR201 Manual de usuario

Stanley

Stanley EZM4000 Guía de solución de problemas

Stanley

Stanley MasterFix XGrip N09QI Manual de usuario

Stanley

Stanley STHM5KS Manual de usuario

Stanley

Stanley Kit 6 Manual de usuario

Stanley

Stanley AV50 Guía de solución de problemas

Stanley

Stanley SPL31A-N Manual de usuario

Stanley

Stanley 55 Instrucciones de funcionamiento

Stanley

Stanley SFP 1250 Manual de usuario

Stanley

Stanley DR19 Manual de usuario

Stanley

Stanley 55 Manual de usuario

Stanley

Stanley SBR20 Manual de usuario

Stanley

Stanley CH18311 Manual de usuario

Stanley

Stanley 8221074STN Series Manual de usuario

Stanley

Stanley GD50 Manual de usuario

Stanley

Stanley 9045670STN Manual de usuario

Stanley

Stanley 07536 Guía de solución de problemas

Stanley

Stanley SST1801 Manual de usuario

Stanley

Stanley STHT82942 Manual de usuario

Stanley

Stanley HP Twin 8 Manual de usuario

Stanley

Stanley CH15 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar