Stanley 204018 Manual de usuario

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 1 of 6

Panic Hardware Exit Device

Installation Manual

Quick-Reference Guide

204018

Rev. A, 12-3-04

Prohibition on Copying

Any unauthorized reproduction, disclosure or distribution of copies by any person

of any portion of this work may be a violation of copyright law of the United

States of America and other countries, could result in the awarding of statutory

damages of up to $250,000 (17 USC 504) for infringement, and may result in

Stanley Access Technologies

Quick-Reference Guide

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 2 of 6

1. Lay SX panel horizontally with escutcheon and cylinder lock facing

down.

2. Install screw #6-32 x 2” into the center block to aid in pulling and

holding the center block in position.

3. Remove Dummy Plate from center block. Be sure to save the two #10-

32 x 3/4” flat head machine screws holding Dummy Plate, as you will

need them for later installation.

4. Locate the center block in the rectangular hole.

5. Align the protruding square of the center block with the square hole in

the mounting plate and place onto the center block. (See Fig. 5.)

6. Place scissor cartridge on center block and secure with the two #10-32

x 3/4” flat head machine screws. (See Fig. 6)

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 3 of 6

7. Secure Crank arm.

a. Remove the #6-32 x 2” helper screw.

b. Align crank arm with shaft. You may have to operate the push

bar scissors to align tab with slot.

c. Secure with one #6-32 x 1/4” truss head. (See Fig. 7)

8. Insert push bar (See Fig. 9) and secure end caps with four #10-32 x

1/2” self-tapping screws. (See Fig. 10)

9. Center Panic bar assembly on mutton bar. Measure six inches down

from end of panic bar. (End opposite to center block) Drill .218” hole

centered through panic hardware and mutton bar. Secure hardware

down with ¼-20 x 1” self-tapping hex head bolt.

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 4 of 6

10.Insert cover strip into back bar. Push in until flush with back bar

extension. (See Fig. 11)

11.Install base caps and secure with four #10-32 x 2” self-tapping screws.

(See Fig.12)

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 5 of 6

12.Adjust bottom throw bolt length.

a. Remove the four #10-32 flat head screws from the guide block in

the bottom of the stile

b. Rotate the bottom throw bolt counterclockwise until it sticks out

5/8” from the bottom of the stile.

c. Replace guide block and four #10-32 flat head screws.

13.Check operations.

a. Fully depress push bar and release

b. Top bolt will retract and latch.

BOTTOM

THROW

BOLT

GUIDE

BLOCK

MOUNTING

SCREWS

Filename: “Panic Hardware Exit Device Installation”

Location: Date Created: 8/16/2004

Issued By: PCN 04-132 Date Revised: 12/3/2004

Revised By: M. Sheehan Page 6 of 6

c. Push the jamb sensor in and you should see about 5/8” of

movement from the top bolt.

Tabla de contenidos

Otros manuales de Herramientas de Stanley

Stanley

Stanley MasterFix XGrip N09QI Manual de usuario

Stanley

Stanley STHM5KS Manual de usuario

Stanley

Stanley DR19 Manual de usuario

Stanley

Stanley EZM4000 Guía de solución de problemas

Stanley

Stanley 160173XSTN Manual de usuario

Stanley

Stanley AL24 Manual de usuario

Stanley

Stanley AV50 Guía de solución de problemas

Stanley

Stanley CH15 Manual de usuario

Stanley

Stanley CH1513101 Manual de usuario

Stanley

Stanley RINGER9/16 Manual de usuario

Stanley

Stanley S32 Manual de usuario

Stanley

Stanley HP Twin 8 Manual de usuario

Stanley

Stanley SBR20 Manual de usuario

Stanley

Stanley SPL31A-N Manual de usuario

Stanley

Stanley 150 Manual de usuario

Stanley

Stanley HSX Series Manual de usuario

Stanley

Stanley 8221074STN Series Manual de usuario

Stanley

Stanley 71501 Guía de solución de problemas

Stanley

Stanley CH15 Manual de usuario

Stanley

Stanley SFP 1250 Manual de usuario

Stanley

Stanley 55 Instrucciones de funcionamiento

Stanley

Stanley TR201 Manual de usuario

Stanley

Stanley Bostitch T55 Series Manual de usuario

Stanley

Stanley STHT82942 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

BGS technic

BGS technic 8578 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar