Stanley NB08PT-18 Manual de usuario

NB08PT-18 Blind nut tool

Battery Power Tool

Accessories

Manual

The information provided may not be reproduced and/or made public in any way and through any means (electronically or mechanically) without

prior explicit and written permission from STANLEY Engineered Fastening. The information provided is based on the data known at the moment of

the introduction of this product. STANLEY Engineered Fastening pursues a policy of continuous product improvement and therefore the products

may be subject to change. The information provided is applicable to the product as delivered by STANLEY Engineered Fastening. Therefore,

STANLEY

Engineered Fastening cannot be held liable for any damage resulting from deviations from the original specifications of the product.

The information available has been composed with the utmost care. However, STANLEY Engineered Fastening will not accept any liability with

respect to any faults in the information nor for the consequences thereof. STANLEY Engineered Fastening will not accept any liability for damage

resulting from activities carried out by third parties. The working names, trade names, registered trademarks, etc. used by STANLEY Engineered

Fastening should not be considered as being free, pursuant to the legislation with respect to the protection of trademarks.

OriginalInstruction

STANLEY Engineered Fastening policy is one of continuous product development and improvement

and we reserve the right to change the specification of any product without prior notice.

Nose Assemblies

Nose equipment varies according to the blind insert nut type being installed. Each nose assembly

represents a unique set of components which can be ordered individually. Component numbers

refer to the illustration below. We recommend maintaining some stock of spares as items will need

regular replacement if worn. Read the Service Manual for nose assembly instructions.

MAIN COMPONENTS LIST

Mandrel

Spin Pull Head Case

Nosepiece

Spin Pull Head

Lock Nut

FR Lever

Nose Housing

Mast Housing

Nose Housing Nut

Nut

Mandrel Lock

*for complete tool explosion and Bill of Material please see service manual

ACCESSORIES CHANGING INSTRUCTIONS

Always wear approved hearing and eye protections at all times when using installation

equipment.

WARNING: Before adjusting tool, always remove the battery pack.

Mounting the mandrel and nosepiece

•Select the correct mandrel (A) and nosepiece (B) for the blind nut (K) to be

installed.

•Loosen the nose housing nut (E), Remove the nose housing (D).

•Press the mandrel lock (F), Loosen and remove the mandrel (A).

•Screw the correct mandrel (A) into Spin Pull Head (H) while pressing the mandrel

lock (F). Lock the mandrel (A)

•Loosen the lock nut (C) and unscrew and remove the nosepiece (B) and Lock nut

(C)

•Screw the Lock nut (C) onto the correct nosepiece (B) and screw the nosepiece (B)

into the nose housing (D) lightly.

•Adjust the position of the nosepiece (B) according to the blind nut (K) to be

installed. The length of mandrel protruding from the top of blind nut (K) to be 0-

0.5mm.

•Tighten the lock nut (C) by a spanner properly.

PLACING SPECIFICATIONS

Nut Type

PLACING CAPACITY

NB08PT-18

M10

Eurosert®

●

Thin Sheet Nutsert®

●

DK/DL

●

Euro Hexsert®/Hexsert®

●

High Strength Hexsert®

●

Squaresert®

●

Standard Nut (Steel)

●

Standard Nut (Aluminum)

●

Standard Nut (Stainless

steel)

●

Closed End Nut

●

Hexagonal Nut

●

All Hexagonal Nut

●

Tetra Nut

●

Knurled Nut

●

Soft Set Nut

●

Slit Nut

●

Pipe Nut

●

HB Bolt

●

HB Bolt for round pipe

●

Note:

Force control can be used for the following sizes only.

Aluminum M6 or more (Except for Slit Nut).

Steel M5 or more.

Stainless steel M5 or more.

MANDREL AND NOSEPIECE

WARNING: When selecting mandrel and nosepiece, always use the compatible parts. Using different

parts may cause nut tightening failure or tool failure.

Note:

1. Refer Table B for Thin sheet Nutsert®.

2. Refer Table C for Thin head Hexsert®.

Table A Mandrel and Nosepiece compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-3*

φ3

PNT600-02-3*

φ4.0

PNT600-01-4

φ4

PNT600-02-4

φ4.5

PNT600-01-5P

φ5

PNT600-02-5

φ5.1

PNT600-01-6P

φ6

PNT600-02-6

φ6.1

PNT600-01-8M

φ8

PNT600-02-8

φ8.1

M10

PNT600-01-10A*

φ10

PNT600-02-10*

φ10.1

6-32 UNC

PNT600-01-632*

φ3.5

PNT600-02-632*

φ3.6

8-32 UNC

PNT600-01-832*

Φ4.1

PNT600-02-832*

Φ4.3

10-24 UNC

PNT600-01-1024*

Φ4.8

PNT600-02-5

φ5.1

10-32 UNF

PNT600-01-1032*

Φ4.8

PNT600-02-5

φ5.1

Table B Thin sheet Nutsert® compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-3*

φ3

TNM00146*

φ3.1

PNT600-01-4P*

φ4

TNM00147*

φ4.1

PNT600-01-5P

φ5

TNM00148*

φ5.1

PNT600-01-6P

φ6

TNM00149*

φ6.1

PNT600-01-8P*

φ8

TNM00150*

φ8.1

Inside Diameter

Outside Diameter

M8×1.0

Inside Diameter

Outside Diameter

M8×1.0

Table C Thin head Hexsert® compatible chart *：Option parts

Nut Size

MANDREL

NOSEPIECE

Part No.

O.D

Part No

I.D

PNT600-01-4P*

φ4

TNM00151*

φ4.1

PNT600-01-5P

φ5

TNM00152*

φ5.1

PNT600-01-6P

φ6

TNM00153*

φ6.1

PNT600-01-8P*

φ8

TNM00150*

φ8.1

MANDREL AND NOSEPIECE

(OPTIONS)

1. Pipe Nut (Made to order)

When fastening the pipe nut SRH-630-191-K2, install the nose assembly for the pipe

nut. The mandrel used is PNT600-01-6P. Please refer to the following list for the

nose assembly components for pipe nuts.

●SRH-630-191-K2

Nose Assembly

TNM00354

SA Mast Housing

TNM00355

SA Nose Housing

TNM00356

Nose Housing

TNM00257

Nose Slider

PNT600-137A

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

PNT600-02-6NP

Lock Nut

PNT600-03

Hexagon socket button bolt

PNT600-100

Spacer

PNT600-138

Outside Diameter

M8×1.0

Inside Diameter

Lock Nut

Slider Spring

Nosepiece

Retaining Ring

Nose Slicer

Nose Housing

SA Mast Housing

Spacer

Button Head Cap Screw

2. Pipe HB Bolt (Made to order)

When fastening pipe HB bolts, install the pipe HB nose assembly. Change the

mandrel attached to the tool to the socket that comes with the nose assembly.

Please refer to the following list for each nose assembly component.

●SRB-630-480LF-K2-180L

Nose Assembly

TNM00358

SA Mast Housing

TNM00355

SA Nose Housing

TNM00359

Nose Housing

TNM00258

Nose Slider

TP134-080

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

TZ024-435

Lock nut

PNT600-03

Button Head Cap Screw

PNT600-100

Spacer

PNT600-138

Socket

TNM00365

●SRB-830-480-K2-70L

Nose Assembly

TNM00360

SA Mast Housing

TNM00355

SA Nose Housing

TNM00361

Nose Housing

TNM00257

Nose Slider

PNT600-137A

Slider Spring

AN600P-31

Retaining Ring

AN600P-32

Nosepiece

TZ034-433

Lock nut

PNT600-03

Button Head Cap Screw

PNT600-100

Spacer

PNT600-138

Socket

TNM00366

Lock Nut

Slider Spring

Nosepiece

Retaining Ring

Nose Slider

Button Head Cap Screw

Nose Housing

SA Mast Housing

Spacer

Socket

3. HB Bolt (Made to order)

When tightening HB bolts, replace the mandrel attached to the following nosepiece

and tool with the following socket to make a tool for HB bolts.

HB Bolt

Socket

Nosepiece

SPB-650R-WB*****

PNT600-01-6HB-WB

PNT600-02-6HB-WB

SPB-625-RLT

PNT600-01-6HB

PNT600-02-6HB

4. Slit Nut (Made to order) *Only can be used by Stroke control

When fastening the slit nut, attach the sleeve to the outer diameter of the

mandrel and replace it with the following nose piece. The mandrel used is

PNT600-01-6P.

Slit Nut

Nosepiece

SPH-640-SLIT

PNT600-02-64SLT-S

ENS-M6SV-S

SPH-670-SLIT

PNT600-02-67SLT-S

Nosepiece

Socket

Sleeve

STANLEY Engineered Fastening

4 Shelter Rock Lane

Danbury, Connecticut,

United States, 06810

Tel. 877 364 2781

Fax 800 225 5614

Holding your world together ®

Find your closest STANLEY Engineered Fastening location on

www.stanleyengineeredfastening.com/contact

For an authorized distributor nearby please check

www.stanleyengineeredfastening.com/econtact/distributors

Manual Number

Issue

C/N

TNM00383

210406-1

Avdel®, Avex®, Avibulb®, Avinox®, Bulbex®, Hemlok®, Interlock®, Klamp-Tite®, Monobolt®, POP®,

ProSet®, Stavex® and T-Lok® are registered trademarks of Stanley Black & Decker, Inc. and its affiliates.

The names and logos of other companies mentioned herein may be trademarks of their respective owners.

Data shown is subject to change without pior notice as a result of continuous product development and

improvement policy. Your local STANLEY Engineered Fastening representative is at your disposal should

you need to confirm latest information.

Otros manuales para NB08PT-18

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Stanley

Stanley

Stanley Fat max Manual de usuario

Stanley

Stanley ST55 Manual de usuario

Stanley

Stanley STCT1830 Manual de usuario

Stanley

Stanley SGC-8000N Manual de usuario

Stanley

Stanley PROSET XT2 76002 Manual de usuario

Stanley

Stanley SBD201S2K Manual de usuario

Stanley

Stanley FATMAX V20 SCR300 Manual de usuario

Stanley

Stanley GD50 Manual de usuario

Stanley

Stanley FATMAX SFMCE510B Manual de usuario

Stanley

Stanley ESAFOR MK II Guía de solución de problemas

Stanley

Stanley FATMAX SBD710 Manual de usuario

Stanley

Stanley BR87320 Manual de usuario

Stanley

Stanley SBT2513 Manual de usuario

Stanley

Stanley SCD20 Manual de usuario

Stanley

Stanley AV-15 Guía de solución de problemas

Stanley

Stanley MBF5 Manual de usuario

Stanley

Stanley FatMax FMC620 Manual de usuario

Stanley

Stanley SDR1400 Manual de usuario

Stanley

Stanley Saber Series Guía

Stanley

Stanley Avdel NeoBolt PB2500N Guía de solución de problemas

Stanley

Stanley ProSet XT3 Manual de usuario

Stanley

Stanley STHR272 Manual de usuario

Stanley

Stanley FatMax SBJ650 Manual de usuario

Stanley

Stanley NB08PT-18 Manual de usuario

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual