Stanley Avdel STD Genesis nG3LB Tool Guía de configuración
nG3LB Tool –Instruction Manual Supplement.
This must accompany the Manual (07900-00930) for the STD
Genesis® nG3 tool
nG3LB Tool
Hydro-Pneumatic Power Tool
Original
Instructi
ons
2
Intent of Use
The Genesis® nG tool must “only” be used for placing 3/16” & 1/4” NeoBolt® as outlined in “Tool setting guide – Small diameter
NeoBolt®: (07900-01071 GB)
Tool Specification
Air Pressure
Minimum - Maximum
5-7 bar
Free Air Volume Required
@ 5.5 bar
4.3 litres
Stroke
Minimum - Maximum
10-29 mm
Pull Force
@ 5.5 bar
12.9 kN
Cycle Time
Approximately
0.8 seconds
Noise Level
Less than
75 dB(A)
Weight
Without nose equipment
2.3 kg
Vibration
Less than
2.5 m/s2
Safety Instructions
For the full safety instructions refer to the associated Genesis® nG tool manual (07900-00930 GB)
Certificate of Conformity
Refer to the associated Genesis® nG Instruction Manual (07900-00930 GB)
3
General Assembly
Base Tool –71256-02000
View Shows ¼” NeoBolt®nose equipment (not supplied as standard)
Parts List
nG3LB NEOBOLT PLACING TOOL VARIANT PARTS LIST
ITE
M
PART NUMBER
DESCRIPTION
QTY
ITEM
PART NUMBER
DESCRIPTION
QTY
1
71256-02001
BODY MACHINED
1
6
07007-02136
SPRING
1
2
07003-00472
O-RING
1
7
71256-02006
LOCK NUT
1
3
71256-02003
SPRING HOUSING
1
8
71256-02005
ADJUSTING NUT
1
4
71256-02004
HYDRAULIC PISTON
1
9
07002-00098
NYLOC NUT
1
5
71256-02008
WASHER
1
10
71256-02007
ADJUSTING STOP
1
*NEW PARTS IN nG3 LIST
6
3
5
1
4
7
8
9
10
0
2
4
Stroke Information
The diagrams below show the minimum and maximum stroke conditions when rotating the adjusting nut 8. When the adjusting nut is
unscrewed beyond the maximum allowable stroke, air will start to leak from the rear of the adjusting nut. Do not use the tool if the air leaks
from the tool. When air leaks from the tool, isolate the air from the tool and then screw the adjusting nut back onto the spring housing 3. The
adjusting nut will not have any air pressure behind it should the end user carry on unscrewing the nut from the spring housing. When setting
the stroke of the hydraulic piston 4, it is highly recommended that the locking nut 7 is tightened into the adjusting nut 8.
5
Fitting Procedure –3/16” NeoBolt Nose Equipment
When placing 3/16” NeoBolt, a spacer is required to reduce the stroke of the tool. Spacer part number 71256-02011. To fit spacer, follow
procedure below:
1. Remove adjusting nut 8
2. Unscrew Nyloc nut 9
3. Unscrew adjusting stop 10
4. Fit 3/16” stroke modification adaptor to adjusting nut 8
5. Screw adjusting stop 10 into adjusting nut 8fully ensuring spacer is retained in between the two items.
6. Screw adjusting nut 8to spring housing 3.
7. Minimum and maximum stroke now 5mm –24mm respectively.
Fitting Procedure –1/4”NeoBolt Nose Equipment
The spacer 71256-02011 as mentioned in section “Fitting Procedure –3/16”NeoBolt Nose Equipment”must be removed prior to placing 1/4”
NeoBolt. Refer to the procedure in this section to remove it.
Minimum and maximum stroke is 10mm and 29mm respectively when the spacer is removed
Maintenance/Dismantling Instructions
THE AIR LINE MUST BE DISCCONNECTED BEFORE ANY DISMANTLING IS ATTEMPTED
1. Unscrew the Adjusting Nut 8from the Spring Housing 3by hand.
2. Unscrew the Spring Housing fully 3using a 25mm A/F spanner. Remove the Spring 6, Washer 5and Hydraulic Piston 4from the
rear of the tool.
3. Refer to tool manual 07900-00930 GB for further disassembly and maintenance.
Re-assemble in the reverse order.
For Safety and Full Servicing and Maintenance instructions, refer to the nG3 Genesis® tool Manual (07900-00930 GB).
Item numbers in bold refer to the parts list on page 2 in this flyer.
6
Manual Number
Issue
C/N
07900-01067
D2
17/275
Avdel UK Limited
Stanley House, Works Road
Letchworth Garden City, Hertfordshire SG6 1JY
Tel. +44 1582 900-000 –Fax -001
© 2016 Stanley Black & Decker, Inc.
Avdel®, Genesis®and NeoBolt®, are registered trademarks of Avdel UK Limited.
AV™ is a trademark of Avdel UK Limited.
The names and logos of other companies mentioned herein may be trademarks of their respective
owners.
This document is for informational purposes only. Avdel UK Limited makes no warranties, expressed
or implied, in this document.
Data shown is subject to change without prior notice as a result of continuous product development
and improvement policy.
Your local STANLEY Engineered Fastening representative is at your disposal should you need to
confirm latest information.
Tabla de contenidos
Otros manuales de Herramientas eléctricas de Stanley
Stanley
Stanley STHR272KS Manual de usuario
Stanley
Stanley FATMAX SFMCD750 Manual de usuario
Stanley
Stanley EXPERT E090501 Instrucciones de funcionamiento
Stanley
Stanley BR45 Manual de usuario
Stanley
Stanley MB656 Manual de usuario
Stanley
Stanley AV 30 Guía de solución de problemas
Stanley
Stanley FatMax FME340 Manual de usuario
Stanley
Stanley 150703XSTN Manual de usuario
Stanley
Stanley SRP 3050 Manual de usuario
Stanley
Stanley FATMAX SCD711 Manual de usuario
Stanley
Stanley POP PB2500 Manual de usuario
Stanley
Stanley STEL670 Manual de usuario
Stanley
Stanley SRR1200 Manual de usuario
Stanley
Stanley NB08PT-18 Manual de usuario
Stanley
Stanley STCT1080 Manual de usuario
Stanley
Stanley Avdel 07287 Guía de solución de problemas
Stanley
Stanley WS10 Guía
Stanley
Stanley ProSet XT1 Instrucciones de operación
Stanley
Stanley 07530 Guía de solución de problemas
Stanley
Stanley Saber Series Guía
