StagePro CROMA 10R Manual de usuario

MANUAL DE USUARIO

CROMA 10R

alienpro.com.mx

alienpromx1 Alien Pro @alienpro_mx Alienpro_mx Alienpro_mx

In order to guarantee the product’s life, please don’t put it in the damp places or even the

environment over 60degress.

Always mount this unit in safe and stable matter.

Install or dismantle should operate by professional engineer.

Using lamp, the change rate of power voltage should be within±10%, If the voltage is too

high, it will shorten the light’s life; If it’s not enough, will influence the effect.

Please restart it 20 minutes later after turning off light, until full-cooling. Frequent

switching will reduce the life span of lamps and bulbs; intermittent using will improve the

life of bulls and lamps.

In order to make sure the product is used well, please read the Manual carefully.

www.ali e n p r o . c o m . m x

www.alienpro.com.mx

To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Intermittently using will extend this item’s service life.

Please clear the fan , fan net , and optical lens in order to keep good work state.

Do not use the alcohol or any other organic solvent to wipe the shell.

1.1 Maintenance

The product has perfect performance and integrity packing. All users should be strictly complying

with the warning and operating instructions as stated. Or we aren’t in charge of any result by

misusing. Any damage resulting by misuse is not within the Company’s warranty. Any fault or

problem caused by neglecting the manual is also not in the charge of dealers.

Note: All information is subject to change without prior notice.

1.2 Statement

10 Gobo 231-235 Gogo14 shake slow-fast speed

236-240 Gogo15 shake slow-fast speed

241-245 Gogo16 shake slow-fast speed

246-250 Gogo17 shake slow-fast speed

251-255 Gogo18 shake slow-fast speed

11 Prism 1 0-63 Prism excluded

64-127 Prism 1 inserted

128-191 Prism 2 inserted

192-255 Prism 3 inserted

12 Prism 0-127 Position 0-360°

1 rotation 128-187 Fast to slow rotation

188-195 Stop

196-255 Slow to fast rotation

13 Prism 2 0-127 Prism excluded

128-191 Prism 4 inserted

192-255 Prism 5 inserted

14 Prism 2 0-127 Position 0-360°

rotation 128-187 Fast to slow rotation

188-195 Stop

196-255 Slow to fast rotation

15 Focus 0-255 From far to close

16 Rainbow 0-127 Rainbow wheel excluded

wheel 128-255 Rainbow wheel inserted

17 Lamp 0-025 Unused range

control 026-100 Lamp off

101-255 Lamp on

18 Reset 0-239 Unused range

240-255 Reset in 3s

1.3 Safety Precaution

Chapter 1 Installation and Attention

Power Input: 127Vca 60Hz

Power Dissipation

Power Consumption: 280W

: 400W

lamp:10R Bulb (life:2200 hours Color temperature: 8000K)

Channel mode:18CH DMX512 Channel

Control mode: DMX, auto-run, master/slave and sound-activate

Pan scan: 540°(16bit) Electric correction

Tilt scan:270° (16bit) Electric correction

Color wheel: 14 colors+white

1.4 Product Instruction

www.alienpro.com.mx

Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm

characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable

with characteristics differing from those specified. The end connections must be made using XLR

type 3 male/female connectors. A terminating plug must be inserted into the last projector with

a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.

IMPORTANT: The wires must not make contact with each other or with the metal casing of the

connectors. The casing itself must be connected to the shield braid and to pin 1 of the

connectors.

1.5 Cable Connection（DMX）

Figure 1 DMX Cable connection

- Gobo 20-24 Gobo4

25-29 Gobo5

30-34 Gobo6

35-39 Gobo7

40-44 Gobo8

45-49 Gobo9

50-54 Gobo10

55-59 Gobo11

60-64 Gobo12

65-69 Gobo13

70-74 Gobo14

75-79 Gobo15

80-84 Gobo16

85-89 Gobo17

90-94 Gobo18

95-125 Forward running from fast to slow

126-130 Stop

131-165 Backward running from fast to slow

166-170 Gogo1 shake slow-fast speed

171-175 Gogo2 shake slow-fast speed

176-180 Gogo3 shake slow-fast speed

181-185 Gogo4 shake slow-fast speed

186-190 Gogo5 shake slow-fast speed

191-195 Gogo6 shake slow-fast speed

196-200 Gogo7 shake slow-fast speed

210-205 Gogo8 shake slow-fast speed

206-210 Gogo9 shake slow-fast speed

211-215 Gogo10 shake slow-fast speed

216-220 Gogo11 shake slow-fast speed

221-225 Gogo12 shake slow-fast speed

226-230 Gogo13 shake slow-fast speed

Fixed gobo: 18 gobos+white

Prism wheel 1: 16-facet prism, 6-facet mirror, 8+24 facet prism

Prism wheel 2: 8-facet prism, 6-facet prism, frost

Rainbow effect

0-100% mechanical dimming, mechanical dimming and free dimming available.

Strobe macro control available.

Beam angle: 3.8-45°

Over heat protection

IP level: IP20

Net weight: 15.7KG

DMX512 2

SIGNAL.-

DMX512

3PIN

SCREEN

SIGNAL.+

This equipment can be positioned and fixed by clamp in every direction of the stage. Locking

system makes it easy to fasten to the bracket.

Attention! Two clamps are needed to fix the equipment. Every clamp is locked by fastener of 1/4

kind. Fastener can only be locked clockwise.

Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary

accessory can not hang on the delivery handle. Nip the equipment on bracket.

Check if rigging clamp (not including the one inside) damaged or not? If stand ten times

weight as the equipment. Make sure the architecture can stand ten times weight as all the

equipments, clamps, wirings and other additional fixtures.

Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to

clamp bracket, and then screw the nuts.

Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock

the two levers by 1/4 rotating clockwise; then install another clamp.

Install on safety string which stands at least ten times weight as equipment. Terminal of

the accessory is designed for clamps.

Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment

to flammable material or lighting source.

Figure 2 Panel diagram

1.6 Rigging (Optional)

9 Color 15-19 Color1+Color2

20-24 Color2

25-29 Color2+Color3

30-34 Color3

35-39 Color3+Color4

40-44 Color4

45-49 Color4+Color5

50-54 Color5

55-59 Color5+Color6

60-64 Color6

65-69 Color6+Color7

70-74 Color7

75-79 Color7+Color8

80-84 Color8

85-89 Color8+Color9

90-94 Color9

95-99 Color9+Color10

100-104 Color10

105-109 Color10+Color11

110-114 Color11

115-119 Color11+Color12

120-124 Color12

125-129 Color12+Color13

130-134 Color13

135-139 Color13+ White

140-199 Forward running from fast to slow

200-255 Backward running from fast to slow

10 Gobo 0-4 White

5-9 Gobo1

10-14 Gobo2

15-19 Gobo3

2.1 Brief

The light panel diagram show as Figure 2, Left area is TFT Displayer, support touch, and right

area is KEY, both of touch and KEY can operate light and setting.

Display & operation just like ‘Android operation system, touch the item will set or modify setting.

Note: Prevent damage the touch or TFT displayer, Can not use sharp objects chick displayer.

Chapter 2 Panel Operation

www.alienpro.com.mx

Figure 3 Dialog of value setting

Channel Function DMX Value Feature

1 Pan 000-255 0-540°

2 Pan fine 000-255 0-2°

3 Tilt 000-255 0-270° 0-1°

4 Tilt fine 000-255 0-1°

5 P/T speed 000-255 From fast to slow

6 Frost 0-127 No effect

128-255 Frost inserted

7 Strobe 0-3 Closed

4-103 Pulse strobe from slow to fast

104-107 Open

108-207 Gradual strobe from slow to fast

208-212 Open

213-251 Random strobe from slow strobe

252-255 Open

8 Dimmer 000-255 0-100% dimmer

9 Color 0-4 White

5-9 White+Color1

10-14 Color1

2.2.1 Operate Light with Touch or KEY

The left area is TFT Displayer and touch, chick item or value with finger will to complete

operation of set light setting (parameters) or view light state.

The area on the right hand side is 4 KEY, As auxiliary input interface, if disable touch

function,, the KEY can be choose to set the parameter..

2.2 Operation

2.2.2 Parameter Value Setting

2.2.3 Boolean Parameter Setting

Modify value: Can quickly modify value via pull the slider to the desired position, or click

the button of ‘up’ or ‘down’ whit finger on the right side to set the exact desired value,

another way is roll encoder on the right hand side of panel.

Apply value:When Value had been modified, Then press the bottom of ‘apply’ in the left

corner to apply to the light, but haven’t saved;

Save Value:Any time, click on the lower right corner of the "OK" button, the setting will

been saved into internal memory.

2.3.6 STAT-->Status: View Status

Enter the page as shown in Figure 11.

Work Mode: Show the current working mode.

Address: Show the current address.

Version: Show the version of the lamp.

Elapse: Working hours after turn on.

Tatol: Cumulative hours of operation

when the selected parameters is a Boolean value (such as ON or OFF), can directly modify

setting by chick corresponding item, the setting will been saved right now.

When the parameter is a key item, chick corresponding item, a dialog shown in Figure 4

will been popup ask for the confirm. Chick ‘sure’ to confirm.

www.alienpro.com.mx

When the selected item is value need to been modified, the dialog shown in Figure 3 will popup

Chick item of main menu, enter corresponding sub menu, shown in Figure 5, total 6 sub menu,

includes class of parameter and status:

ADDRESS: Set light DMX address.

WORKMOD: Set light work mode, master or slave mode when in auto run mode.

DISPLAY: Set display parameter, eg. select language.

TEST: Used for test light, modify DMX channel data to test functionthe corresponding

function of reference channel function table.

ADVANCE: Set light running parameter.

STATUS: View light current status.

Figure 10 page of run parameter Figure 11 page of status

Figure 4 Dialog of confirm

Figure 5 Parameter menu

2.3 Operation and Parameter Instruction

2.2.4 Sub Menu (Parameter)

2.3.4 TEST--> Test Mode

Enter the page as shown in Figure 9, light will into test mode, in this mode, the light does not

receive the data for DMX controller:

PAN: range for 0 to 255; GOBO: range for 0 to 255;

TILT: range for 0 to 255; PRISM: range for 0 to 255;

FOCUS: range for 0 to 255; FROST: range for 0 to 255;

COLOR: range for 0 to 255; STROBE: range for 0 to 255;

2.3.5 ADVA-->Advanced: Set Light Run Parameter

Enter the page as shown in Figure 9, set the parameter of light

Pan Invert: Reverse PAN move

OFF--> Pan Normal move. (Default)

ON--> Reverse PAN move.

Tilt Invert: Reverse TILT move

OFF--> Tilt Normal move. (Default)

ON--> Reverse Tilt move.

P/T Rectify: Disable or enable position rectify function.

OFF--> Disable P/T rectify

ON--> Enable P/T rectify-(Default)

Pan Offset: Set PAN original position. Default: 10

Tilt Offset: Set TILT original position. Default: 10

Lamp when: PowerON--> Turn on the lamp when power on. (Default)

RstDone--> Turn on the lamp after reset.

Manual--> Manually turn on the lamp.

Data hold:

OFF--> When no DMX signal, return to middle position. (Default)

ON--> When no DMX signal, stop in the final position.

Factory Setting: Restore all parameter to factory setting.

Via following operation, enter sub menu (parameter menu) shown in Figure5

In main menu, chick 1/6 function button into corresponding parameter menu.

In sub menu(page), chick main item on the left side of displayer, can shift to corresponding

sub menu(page) quickly.

www.alienpro.com.mx

Figure 8 page of display Figure 9 page of Test

Figure 6 page of DMX Address Figure 7 page of work mode

2.3.1 ADDR--> Address: Set DMX Address 2.3.3 DISP-->DISPLAY: Set Display

Click and select the "ADDR", can enter the page of DMX address setting, range from 1 to 512, the

address code shouldn’t is not greater than (512- channels quantity), otherwise the light will not

been controlled. Following is the operation:

Enter the page of DMX address, as shown in Figure 6, click the blank area in right side of display will

pop-up dialog as in Fig. 3, modify value, then click ‘ENTER’ to confirm and save DMX address code.

2.3.2 MODE--> Work Mode: Set Light Work Mode

Enter the page of ‘Work Mode’ as shown in Figure 7 and modify setting. Can set light work mode,

control lamp and DMX channel mode.

DMX Ctrl: Choose to set DMX Mode,

Auto Run: Choose to set Auto Mode,

Sound Ctrl: Choose to set Sound Mode,

M/S Choose: Available just in ‘AUTO RUN’ or ‘SOUND Ctrl’ mode.

ON--> Master. (Data will be sent to other slave lamp immediately.)

OFF--> Slaver. (NOT send data to other lamp via DMX Cable). (Default)

Light Switch:

ON--> Turn on the light,

OFF--> Turn off the light.

Channel Qty: Light support 2 DMX Channel mode: sample or extend.

Simple --> 16CH. (Default)

Expand--> 20CH (or null).

Light support 2 language, rotation display, Enter page as shown in Figure8 to set parameter

following:

Language: English / 中文.

Screen Saver: When panel is idle(these is no operation in 10 seconds), displayer will enter

saver status.

OFF--> No screen saver.

Mode1--> Power-saving mode, turn off the display.

Mode2--> Displays the current address.

Mode3--> Displays the icon and the current working mode.(Default)

Screen Rotation: To turning display.

ON--> Normal display. (Default)

OFF--> 180° turning display.

Touch enable: Disable or enable touch function,.

ON--> Enable touch function.(Default)

OFF--> Disable touch function.

Touch adjust:Adjust touch function. Normally, not enter this item.

www.alienpro.com.mx

Tabla de contenidos

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario