CHAPTER 1 LEI-4361DMX
1
Safety Instruction
1. Make sure the Light Engine and Power Source have the same voltage;
2. Keep out of rain or moist area to avoid shock hazards;
3. Avoid to use at high ambient temperature ( >40℃);
Welcome to use Minar professional LED light engine, LEI-4361DMX. Please read
the manual carefully before turning on the power. If you have any questions
concerning the operation or maintenance, please contact your wholesaler.
LIGHT ENGINE
USER MANUAL
1. Technical Data
2. Installation dimension of light engine(see Fig.1):
Life of LED : 50000H
Standard aperture: Φ28mm/Φ24mm/Φ20mm (Optional:Φ30mm Max)
3
Size: 291×264×135mm
Gross Weight: 7.0Kg
Voltage: 110V~230V AC
Power: 160W
Color : RGBW
Light Source: 1-4X36W LED
3. Light Engine Setup
There are three control modes of LEI-4361DMX, the DMX512 protocol light engine:
* DMX512 Signal Control Mode: DMX512 Signal is received from a DMX512 console.
* Master/Slave Mode: One Light Engine is set as Master, while the rest light engines
are set as Slave. Master sends control signal to slave so that all the machines run the
program synchronously.
* Audio Control Mode: Light engines are controlled by sound.
135
11 0
LED LIGHT ENGINE
MENU
UP DOWN
MIC
AERI AL
275
291
26 4
Fixing Flange
Menu(UP,DOWN)
Fan
Fig. 1
FUSEPOWER
SWITCH
Fuse
Power switch
Power cable
DMX IN
DMX OUT
Aerial (optional)
DMX IN
DMX OUT
2
(3)The connection of DMX Signal Control Mode(See Fig. 2): Fig. 2
DMX512 Console
Slave 2 Slave 3
Slave 1
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
AERIA L
FUSEPOWER
SWITCH
DMX IN
DMX OUT
(1) DMX 512 signal control mode:
DMX address setup:
When a DMX512 console is used, all the light engines, LEI-4361DMX, in the group should be
set up as slave machines with DMX address of “001".
DMX Channels: 8 Channels
CH1:Red CH2:Green CH3:Blue CH4:White CH5:Speed (16 Tiers)
CH6:Dimmer(8 Tiers) CH7: Strobe (8 Tiers) CH8: Twinkle(8 Tiers)
(2) Master/Slave mode:The settings of Master/Slave light engine:
Notice:
REMARKS
Adjusting of brightness ,total 8 levels :d.00,d.10,d.20,
d.35,d.50,d.70,d.85,d.99.(d.99.means100% brightness)
Setting of twinkle wheel speed, total 8 levels:
0RPM,1RPM,2RPM,3RPM,4RPM,5RPM,8RPM,12RPM
22 preset programs(see attached list,when it
display “P.XX”,press “UP/DOWN” to get into
this menu)
PS.1-PS.2 are audio control programs (when it
display “PS.X”,press “UP/DOWN” to get into
this menu)
Setting of program running speed, total 8 levels:
0S,1/4S,1/2S,1S,2S,3S,5S,8S
DESCRIPTION OF FUNCTIONS
DMX address, “001”-“505” are available
MENU
No.
1
2
3
4
5
6
Slave
DMX Receiver
MASTER
STATUS
r.on: Remote control is on,
r.oF: Remote control is off.
. .
. .
. .
. .
. .
. .
1.Hold and press the two buttons at
the same time for 3 seconds to
unlock the menu for setting up.
2. Hold and press the button “UP”,
at the same time to press the
button“DOWN” to switch the
menu.Then release both bottons.
3. Press either button of “UP” or
“DOWN” to choose the right
parameter.
4. After 60 seconds, the data will be
saved and the menu locked.
5. When the display is on, the dot
next to the third digit will flash
if there is any DMX signal coming
in.
1 If you need Master/Slaves to change color synchronously, please set all of slaves as “001”;
2 If you need Master/Slaves to chase to change color, please set the first slave machine as
“009”, the second one as “017” and so on (add “8” one after another) ..
4 options of DMX channels numbers available when
control led by a DMX console. :1 channel (Colors);
: 4 channels (Ch1:R,CH2:G,CH3:B,CH4:W);
: 5 channels (Ch1:R,CH2:G,CH3:B,CH4:W;
CH5:Wheel speed); : 8 channels by default.
7
*
Holding button “UP” and press “DOWN” continuously until the display shows three digits
between 001-505 in editting mode, press the button “UP” or “DOWN” to select the address.
