3
•The connections on both sides of the mains cable
(the appliance and the power socket) should never
be strained. If the mains cable is damaged it must
be replaced by a qualified person or service to
avoid any hazards.
•This appliance must not be operated by an
external timer or a remote control system.
•The top of the base unit ishould always be
kept dry, especially around the connection area.
•Before drying, disconnect the power supply;
ensure that the base unit iis completely dry
before you reconnect the appliance to power
supply.
•Pour the water out of the kettle slowly and
carefully, do not over tilt or tip the kettle too
fast to prevent spillage and splashing. Remove
the kettle jug rfrom the base unit ibefore
filling or pouring.
•Do not move the kettle when it is switched on.
Use extreme caution when moving a kettle jug r
containing hot water.
•Do not switch the kettle on unless it contains at
least two cups of water.
•Avoid filling it up above the MAX mark to
prevent the hot water spewing out.
•Always remove the kettle jug rfrom the base
unit ibefore you fill it.
•Always close the lid eand have the filter in
place before you switch the kettle on. Do not
open the lid ewhile the water is boiling.
•Avoid contact with steam while the water is
boiling and after the kettle is switched off.
•Avoid using the kettle near or below curtains,
shelves, cupboards or anything that might be
damaged or deformed by hot steam.
•Use the handle wand knob eon the appliance
and avoid touching any hot surfaces.
•The switch ushould never be held fixed in the
ON position as this may cause damage to the
switch-off mechanism.
•Do not remove the kettle jug rfrom the base
unit iwithout switching it off first. Unplug the
base unit iwhen not in use.
•Unplug the kettle from the power socket before
cleaning or removing any parts. Ensure that the
kettle is completely cooled down before cleaning
and storing away. Keep the kettle jug r, base
unit i, mains cable, and plug away from sources
of heat and store in a dry place.
•Do not use the kettle for any purpose other
than heating water.
•Use the kettle jug ronly with the base unit i
supplied and do not tamper with the connector
in any way.
A scald hazard can last for a long time after
boiling. Take care when opening the lid eas
steam will escape from the opening. If scalding
does occur, immediately run cold water over the
affected area and seek medical assistance.
BEFORE FIRST USE
Fill to the MAX mark, boil, discard the water,
then rinse. Do this three times, to remove
manufacturing dust. Ensure that the electrical
connections are completely dry before use.
SAFE HANDLING
•Pour water from the kettle jug rslowly to
prevent splashing and scalding with the hot
water.
•Fill the water from the top to help free the filter
from limescale build-up. There should always
be a minimum amount of water in the kettle
before you switch it on (MIN mark on the water
level indicator t).
•To save time and electricity, only boil the
necessary amount of water.
SWITCHING ON
•Place the kettle jug ron the base unit i.
Make sure that the kettle jug ris secure on the
360˚connector.
•Plug the mains cable of the base unit iinto a
power socket before switching the power on.
•Switch the kettle ON. The ON/OFF switch twill
light up and the kettle will start heating the water.
SWITCHING OFF
•Once the water is boiled the kettle will
automatically switch off.
•Lift the kettle jug rfrom the base unit iand
hold it level to avoid splashing the hot water.
•To boil the water again, place the kettle jug r
back on the base unit iand switch it on again.
•If there is not enough water in the kettle jug r,
it will switch off automatically. To switch it back
on, refill the kettle jug rand wait a few minutes
to cool down.
Using insufficient water will shorten the
service life of the appliance.
WATER TEMPERATURE GAUGE
Do not attempt to remove the water
temperature gauge ofrom the kettle jug r.
The water temperature gauge oshows the
temperature of the water inside the kettle. The
gauge owill not work if there is insufficient
water in the kettle jug r. There may be +/-5˚C
variation of temperature.
CARE & MAINTENANCE
Before cleaning always check that the kettle is
switched off and has completely cooled down.
•Unplug the base unit iand let the kettle cool
down completely.
•Wipe the kettle jug r,inside and out, with a
damp cloth. Do not use abrasive cleaners on the
outside of the appliance to avoid scratching the
surface. Be very careful with the temperature
gauge bar aas it is extremely sharp.
