SprintSc Ssc613w Manual de usuario

802.11 b/g Wireless IP Camera

With pan/tilt function

User Manual

Revision: 020205

Date: 2009/04/21

For firmware version v020205

SprintSc Pan/Tilt IP Camera

Table of Contents

1. INTRODUCTION.............................................................................................................................6

2. HARDWARE DESCRIPTION AND QUICK INSTALLATION/USAGE .................................8

2.1. MAJOR HARDWARE COMPONENTS..........................................................................................8

2.2. QUICK INSTALLATION AND USAGE...........................................................................................9

2.3. WIRELESS CONNECTION........................................................................................................13

3. WEB CONFIGURATIONS...........................................................................................................15

3.1. INFORMATION .........................................................................................................................16

3.2. VIDEO DISPLAY ......................................................................................................................17

3.3. NETWORK...............................................................................................................................19

3.4. WIFI SECURITY.......................................................................................................................21

3.5. ADVANCED NETWORK ...........................................................................................................24

3.6. VIDEO SETTINGS....................................................................................................................25

3.7. 3GPP/RTSP SETTINGS.........................................................................................................27

3.8. EMAIL/FTP ALARM..................................................................................................................28

3.9. DI/DO SETTINGS....................................................................................................................30

3.10. NAS SETTINGS.......................................................................................................................31

3.11. SD-CARD SETTINGS ..............................................................................................................33

3.12. SCHEDULING ..........................................................................................................................35

3.13. LED DISPLAY CONTROL.........................................................................................................37

3.14. DATE/TIME..............................................................................................................................38

3.15. ADMIN .....................................................................................................................................39

3.16. UPGRADE................................................................................................................................40

3.17. REBOOT..................................................................................................................................42

3.18. SAFE MODE............................................................................................................................43

3.19. SET TO FACTORY DEFAULT ....................................................................................................44

4. FEATURES AND SPECIFICATIONS........................................................................................45

4.1. FEATURES...............................................................................................................................45

4.2. SPECIFICATIONS.....................................................................................................................46

5. PACKAGE CONTENTS...............................................................................................................49

APPENDIX A. LIST OF TESTED NAT/ROUTER DEVICES..........................................................50

APPENDIX B. MAXIMUM ALLOWED VIDEO USERS...................................................................51

APPENDIX C. PERFORMANCE INFORMATION ...........................................................................52

SprintSc Pan/Tilt IP Camera

APPENDIX D. TROUBLE SHOOTING ..............................................................................................53

APPENDIX E. 3GPP/ISMA OPERATION..........................................................................................56

APPENDIX F. THIRD PARTY AND EMBEDDED WEB PAGE INTEGRATION.........................57

SprintSc Pan/Tilt IP Camera

List of Figures and Tables

Figure 2-1: Major components in the front panel

Figure 2-2: Major components in the back panel

Figure 2-3: IP CAM connection diagram.

Figure 2-4: Connect Ethernet cable to a switch/router.

Figure 2-5: The installation CD disk

Figure 2-6: The ID/Password card

Figure 2-7: Running window of CamView program

Figure 2-8: Pop-up play-video password window

Figure 2-9: Unplug the Ethernet cable to enable the WiFi function

Figure 3-1: Open the web configuration page from CamView software

Figure 3-2: IP CAM Web configuration login page

Figure 3-3: IP CAM Information page

Figure 3-4: Video display page

Figure 3-5: Network settings page for DHCP function

Figure 3-6: Network settings page for fixed IP address

Figure 3-7: WiFi security disabled page

Figure 3-8: WiFi security enabled page

Figure 3-9: WiFi testing page

Figure 3-10: Advanced network settings page

Figure 3-11: Video settings page

Figure 3-12: 3GPP/RTSP enabled page

Figure 3-13: Email/FTPAlarm page

Figure 3-14: D/O Settings page

Figure 3-15: NAS Storage settings page

Figure 3-16: SD-Card settings page

Figure 3-17: SD-Card information page

Figure 3-18: Schedule Management page

Figure 3-19: Led Control settings page

Figure 3-20: System date/time settings page

Figure 3-21:Admin settings page

Figure 3-22: Firmware upgrade settings page

Figure 3-23: Firmware upgrade status page

Figure 3-24: System reboot settings page

Figure 3-25: System reboot under-going page

Figure 3-26: Safe mode information page

Figure 3-27: Stick the reset button to set to the factory default

SprintSc Pan/Tilt IP Camera

Figure 5-1: The IP camera body

Figure 5-2: Power Adaptor

Figure 5-3: Quick installation guide

Figure 5-4: Ethernet cable

Figure 5-5: Installation CD

Figure 5-6: ID/Password Card

Table A-1: List of tested Wireless AP/router devices

Table A-2: List of tested Wired NAT/router devices

SprintSc Pan/Tilt IP Camera

1. Introduction

The Pan/Tilt IP Camera is designed with the “user-friendly” idea deep in mind.

The user can install the IP camera easily on his/her home network and then access

the IP Camera anywhere in the world through the accompanied video management

software - CamView program without setting some complicated DNS name or

changing the router’s settings. It’s just a plug & play action.

With pan/tilt support, users can monitor the video in a much larger viewing angle

range.

For indoor surveillance and remote monitoring, the IP camera provides the best

image quality in its class, and excellent performance. The Pan/Tilt IP Camera also

provides the best bandwidth efficiency, it offers 640x480 resolution, 30 fps frame rate,

real MPEG4 image compression ability. The built-in microphone enables remote

users to not only view, but also listen for additional monitoring options.

With 3GPP/ISMA support, users can see the video of the IP camera on any 3G

mobile phone anywhere, anytime. The big difference is that there is software for

downloading to the mobile phone so that the fixed IP address is not needed for the IP

camera. The video settings including frame rate, resolution and bandwidth could be

different for PC monitoring and mobile viewing. With pan/tilt support, users can

monitor the video in a much larger viewing angle range.

The NAS storage function can easily turn any NAS device to a NVR device. The

schedule function provides full scheduling of email/ftp sending, motion detection and

NAS recording event. With the built-in Web server, the IP Cameras can also be

managed from a standard web browser on a Windows computer. With the ActiveX

support, users can also see the video display on the Windows IE browser.

The Pan/Tilt IP Camera provides both wireless IEEE 802.11 b/g and wired

Ethernet network interfaces for flexible installation. It supports the WEP and WPA

(Wi-Fi Protected Access) security modes to provide the best security for wireless

networks.

The Pan/Tilt IP Camera provides motion detection function. Users can easily

setup this function and receive the notification with the snapshot images through

email and/or ftp when some motion events are detected.

The Pan/Tilt IP camera is ideal for securing small businesses, home offices and

residences over a local area network and/or the Internet.

The differences

It’s very easy to see the video of the Pan/Tilt IP Camera, you only need to key in

SprintSc Pan/Tilt IP Camera

the ID/Password of the IP CAM any where in the world, you do not need to remember

the IP address or domain name or DDNS name or port number. And you do not need

to modify the settings(like port mapping, fixed IP, DDNS, virtual server) of the

NAT/router devices, it’s just a plug & play usage.

So, the differences are the followings:

♦Public IP address needed ? No

♦Dynamic DNS needed ? No

♦Port mapping in router? No

♦Virtual server in router ? No

♦UPnP support in router ? No

♦What’s needed ? ID and Password

SprintSc Pan/Tilt IP Camera

2. Hardware description and quick installation/usage

The IP CAM is designed to be very easy to install and use. First, let’s see the

major components of the IP CAM products.

2.1. Major hardware components.

The major components on the front panel of the IP CAM products are the built-in

microphone, lens and LEDs :

1. Microphone – for receiving the audio/voice. Effective distance is about 5 meters.

2. Lens – the lens is inside the mask and the focus of the lens is fixed, you do not

need to spend time to adjust the focus, the effective focus range is from 30cm to

infinity.

3. Status indication LED (red) – this LED is to indicate the Internet connection status.

When the Internet connection is connected, the LED will be constant red light. If

there is any Internet connection problem, the LED will be blinking red light.

4. Ethernet indication LED (blue) – this LED is to indicate if the Ethernet link is ok

and packet traffic is sending/receiving. When the Ethernet cable is connected, the

LED is constant blue light. When there is packet sending/receiving, the LED is

blinking blue light.

Figure 2-1: Major components in the front panel

The major components on the back panel of the IP CAM products are the bracket

screw jack, power jack, Ethernet jack and reset button:

1. Bracket screw jack – this is the position to screw in the bracket of the IP CAM.

With the bracket, you can put the IP CAM on the desk, on the wall or on the ceiling.

(Bracket not provided)

2. Power jack – this is the place to plug in the power adaptor. The power needed for

this IP CAM is 5V/1.0A, please make sure you are using the correct power

SprintSc Pan/Tilt IP Camera

adaptor.

3. Ethernet jack – this is the place to plug in the RJ45 Ethernet cable. When the

Ethernet link is ok, the Ethernet indication LED on the front side will be blue light.

4. Reset button – this is the button to reset the IP CAM to default factory settings.

You need to use a small stick like pencil or tooth stick to press the reset button for

more than 3 seconds to enable the reset function. Usually when you forgot the

administrator account, you will probably need to do this reset action to reset to the

default factory settings. Please refer to section 3.19 for more details.

5. Wall mount – this is the place to hang the IP CAM on the ceiling or on the wall.

6. Antenna – this is the 802/11 b/g wireless antenna.

7. Digital I/O : one digital input and one digital output is provided to give users control

to alarm speaker or to signal alarm detection.

8. Micro-SD card slot – for inserting the micro SD-Card. (support up to 16G bytes)

Figure 2-2: Major components in the back panel

2.2. Quick installation and usage

There are only three things that you need to do to see the video from the IP CAM.

1. Connect the IP CAM to the home/office network.

2. Install the CamView software on the notebook/PC.

3. Key in the ID/password of the IP CAM(from the ID/Password card) on the

CamView, and then you can see the video.

First, Connect the IP CAM to the home/office network

Please connect the IP CAM accessaries to the IP CAM body correctly, including

the power adapter and Ethernet cable, as shown in Figure 2-3. And connect the other

end of the Ethernet cable to the home network or office network. Usually, this Ethernet

cable is plugged into a home NAT/router device or an Ethernet switch if in the office,

as shown in Figure 2-4. Since the default settings of the IP CAM use DHCP function

SprintSc Pan/Tilt IP Camera

and very often there is a DHCP server on most of the Home/office network, the IP

CAM should be connected to the Internet immediately. The Internet status LED is

constant red light to indicate this good connection status. If the LED is blinking, please

refer to section 3.3~3.5 to try other network settings.

Figure 2-3: IP CAM connection diagram.

Figure 2-4: Connect Ethernet cable to a switch/router.

Second, Install the CamView software on the notebook/PC

Please insert the installation CD into the CD-ROM drive in your notebook or

personal computer (must be running Microsoft Windows OS). Execute the program

CamViewInstaller-xxx.exe on the disk. The program will pop-up some windows about

the installation options, please press the “next” button to proceed with the installation.

After the installation is complete, there will be a CamView icon on the desktop of your

computer screen, please execute this icon. The CamView program will run

immediately.

Tabla de contenidos

Otros manuales de Cámara IP de SprintSc

SprintSc

SprintSc IP Cam w Manual de usuario

SprintSc

SprintSc IP Cam w Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario

SprintSc ssc613w Manual de usuario

Manuales populares de Cámara IP de otras marcas