Spraying Systems TeeJet TECHNOLOGIES BoomPilot Manual de usuario
BOOMPILOT®
INSTALLATION MANUAL
Automatic Boom Section Control for
TJ744E with 5 sections and Matrix Pro
Copyrights
© 2011 TeeJet Technologies. All rights reserved. No part of this document or the computer
programs described in it may be reproduced, copied, photocopied, translated, or reduced
in any form or by any means, electronic or machine readable, recording or otherwise,
without prior written consent from TeeJet Technologies.
Trademarks
Unless otherwise noted, all other brand or product names are trademarks or registered
trademarks of their respective companies or organizations.
Limitation of Liability
TEEJET TECHNOLOGIES PROVIDES THIS MATERIAL “AS IS” WITHOUT WARRANTY
OF ANY KIND, EITHER EXPRESSED OR IMPLIED. NO COPYRIGHT LIABILITY
OR PATENT IS ASSUMED. IN NO EVENT SHALL TEEJET TECHNOLOGIES BE
LIABLE FOR ANY LOSS OF BUSINESS, LOSS OF PROFIT, LOSS OF USE OR DATA,
INTERRUPTION OF BUSINESS, OR FOR INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES OF ANY KIND, EVEN IF TEEJET TECHNOLOGIES HAS
BEEN ADVISED OF SUCH DAMAGES ARISING FROM TEEJET TECHNOLOGIES
SOFTWARE.
Safety Information
TeeJet Technologies is not responsible for damage or physical harm caused by
failure to adhere to the following safety requirements.
As the operator of the vehicle, you are responsible for its safe operation.
The BoomPilot is not designed to replace the vehicle’s operator.
Do not leave a vehicle while the BoomPilot is engaged.
Be sure that the area around the vehicle is clear of people and obstacles before and during
engagement.
The BoomPilot is designed to support and improve efciency while working in the eld.
The driver has full responsibility for the quality and work related results.
Disengage BoomPilot before operating on public roads or when not in use to prevent loss
of vehicle control.
iii
020-053-UK R2
BoomPilot®
Table of Contents
MATRIX PRO® WITH TJ744E SPRAYER CONTROL IV
INTRODUCTION TO TJ744E ABSC 1
Principle of Operation............................................................................. 1
Required Parts ......................................................................................... 1
INSTALLING THE TJ744 ABSC KIT 3
Connecting to Power............................................................................... 3
Battery Cable (Option) .....................................................................................3
Mount & Connect SDM ............................................................................ 4
Power/CAN/Data Cable to BoomPilot Harness ..................................... 4
SYSTEM CHECK 5
Check AUTO mode: ..........................................................................................5
TJ744E Switch box:......................................................................................5
Matrix Pro: ....................................................................................................5
Check MANUAL mode:.....................................................................................5
TJ744E Switch Box: .....................................................................................5
Matrix Pro: ....................................................................................................5
CONFIGURATION USING YOUR MATRIX®PRO 6
Vehicle Setup ........................................................................................... 7
Implement - SmartCable or SDM............................................................ 8
OPERATION USING YOUR MATRIX®PRO 9
Off/Manual & Automatic ..................................................................................9
All Booms On Mode .........................................................................................9
Example......................................................................................................10
BoomPilot Status............................................................................................10
iv www.teejet.com
BoomPilot®
Matrix Pro® with TJ744E Sprayer Control
This installation manual covers installation and setup of the TeeJet 744E Sprayer Control
(with 5 sections) with the Matrix Pro. We have endeavoured to deliver a fault free product.
To ensure optimal use of the equipment, we ask you to pay great attention when reading
this manual. Regarding responsibility for use of the product, we refer to our sales and
delivery terms - especially paragraph 7, which follows:
Product usage.
7.1 Any use of the product is at the sole risk of the
buyer. The buyer is therefore not entitled to any form
for compensation caused by, for example, any of the
following:
• Disturbance to/from any electronic services or
productsthatdonotconrmtothestandards
for CE marking,
• Missing or poor signal coverage or a
succession hereof from external transmitters/
receivers, used by the buyer,
• Functional faults, which apply to or from a
PC-program or PC-equipment, not delivered by
the seller.
• Faults that may arise from the buyers
negligence to react to warnings and fault
messages from the product, or which can be
traced to negligence and/or absent constant
control of the work carried out in comparison
to the planned job.
7.2 When implementing any new equipment the buyer
must take great care and pay attention. Any doubts as
to correct operation/use should result in contacting
TeeJet Technologies.
Kind regards,
TeeJet Technologies
Mølhavevej 2
9440 Aabybro
Denmark
Tel. +45 9696 2500
Fax +45 96962501
www.teejet.com
1
020-053-UK R2
BoomPilot®
INTRODUCTION TO TJ744E ABSC
The Matrix Pro is a combined Guidance and Automatic Boom Section Control (ABSC)
device that features control of up to 15 boom sections. The Matrix Pro connects in parallel
to the existing wiring loom to the section valves.
Principle of Operation
The Matrix Pro controls the section valves according to the GPS position as well as the
GPS guidance to avoid overlaps or skips.
The Matrix Pro controls the section valves in automatic mode. The section switches should
be set to off unless the operator wants to override the auto mode and thus force spraying.
The Matrix Pro monitors the section switches that control the valves in manual mode. The
master switch can be used both in automatic mode and in manual mode.
Required Parts
To add Automatic Boom Section Control to a TJ744 Sprayer Control kit, the following part
numbers are required:
Item Part Number Description Quantity
A 90-xxxxx* Matrix Pro Guidance Controller Kit .................................................1
B 198-396 TJ744 ABSC Cable, 5 Section........................................................1
C 45-05626 Power/CAN/Data Cable, Matrix Pro................................................1
*Part number is dependent on kit contents
2www.teejet.com
BoomPilot®
Figure 1-1: System Diagram
Regulation
S1
S2
S3
Master
1
1
1
1
1
2
2
2
2
2
B
B
A
A
A B
xxx-xxx
xxyyxx
BA
12
3
4
5
6
7
Pos. Part # Description
1 90-xxxxx* Matrix Pro Guidance Controller
2 45-05626 Power/CAN/Data Cable, Matrix Pro
3 75-50061 TJ744E Sprayer Control, 5 sections
4 45-05789 Power Cable for TJ744E including
COBO connection
5 78-05072 Section Driver Module
6 198-396 TJ744E ABSC Cable, 5 sections
7
199-370 TJ744E Harnes for ARAG Manifold,
5 sections
45-10134 TJ744E Harnes for TJ430 Manifold,
5 sections
*Part number is dependent on kit contents
3
020-053-UK R2
BoomPilot®
INSTALLING THE TJ744 ABSC KIT
Connect the automatic boom section kit as shown on the system overview diagram,
Figure 1-1. The kit includes all necessary connectors to get electrical contact with the
TJ744E system.
Connecting to Power
Figure 1-2: Connecting to Power
+-
1
1
2
2
1008-0189
15/30
82
31
Pos. Description
1 +12V (15/30)
2 Ground (31)
Battery Cable (Option)
The power supply must be strong enough to operate the valves. The total current will
depend on the type of valve used.
If a power connector (socket) is not available in the tractor cabin, an optional battery cable
can be used (PN 96ET14).
4www.teejet.com
BoomPilot®
Mount & Connect SDM
Mount SDM to the operator’s preference where LED’s can be seen for troubleshooting.
Connect SDM to BoomPilot Harness.
Figure 1-3: LED Description
Section Power
On – boom section power is on
Off – boom section power is off
In/Out Error
Off – boom output is high or on
Blinking – boom output is low or off
Auto Mode
On – auto mode is active
Off – manual mode is active
CAN Data
Blinking – receiving console CAN messages
Off – CAN messages stop for > 3 seconds
CAN Power
On – CAN power is on
Off – CAN power is off
Power/CAN/Data Cable to BoomPilot Harness
Connect Power/CAN/Data Cable to BoomPilot Harness.
Figure 1-4: Connect Power/CAN/Data Cable to BoomPilot Harness
POWER IN
CAN
RS-232
Power/DATA
45-05626
Power/CAN/Data Cable 10A Fuse
to RS-232
BoomPilot Harness
5
020-053-UK R2
BoomPilot®
SYSTEM CHECK
After connecting the power connector, it is time to make a system check. To check the
system, it is necessary to have full GPS signal. To obtain full GPS signal, the vehicle must
be placed outside.
Check AUTOMATIC mode:
TJ744E Switch box:
Section switches should be in the OFF position when working in Automatic mode. The
Master switch will control the sprayer and should be ON to enable automatic switching of
the sections.
Figure 1-5: Automatic to All Booms On Mode
2.0 km/h 0.76 ha
Mark A
AA
Matrix Pro:
• Turn on the Matrix Pro console
• Encode the number of sections
and the width of each
(Refer to the Matrix Pro user
manual)
• Wait for GPS signal
• Set the BoomPilot mode to
AUTOMATIC
◄Status Bar Icon will change
to green
• Drive forward (> 2 km/h)
• Observe that all valves open
• Check that the valves close
when the Master switch is set to OFF
Check MANUAL mode:
TJ744E Switch Box:
• Set the section switches to ON
• Set the Master switch to ON
Matrix Pro:
• Set the BoomPilot mode to MANUAL
◄Status Bar Icon will change to red
• Check in the ‘Vehicle View Screen’ (Matrix Pro) that the section icons turn off and on
according to the valve/switch status
• Observe that all valves are open
6www.teejet.com
BoomPilot®
CONFIGURATION USING YOUR MATRIX®PRO
The Matrix Pro is used to congure the vehicle and its implements including ABSC.
To access BoomPilot conguration options:
1. Press UNIT SETUP bottom tab .
2. Press CONFIGURATION side tab .
3. Select from:
►Vehicle – used to establish vehicle type, antenna height, direction to boom and
distance to boom
►Implement – used to establish number of boom sections, guidance width, spray
width, overlap percentage, implement delay on time and implement delay off time
►Lightbar – used to establish LED brightness, LED mode and LED spacing
Figure 1-6: Configuration Options
Conguration
Vehicle Implement
AutoSteer Tilt
Lightbar GPS
Video
Figure 1-7: Configure Vehicle and Implement Options
Cong-> Vehicle
12.50 ft
0.00 ft
Front Wheel
Backward
Vehicle Type
Ant Height
Dir to Boom
Dist to Boom
Cong->Implement
Num Sections
Spray Width
Guidance Width 60.00 ft
144.00 ft
15
Cong->Implement (2)
Overlap
Delay O
Delay On 1.00 s
1.00 s
50%
Otros manuales para TeeJet TECHNOLOGIES BoomPilot
6
Tabla de contenidos
Otros manuales de Sistema de control de Spraying Systems
Spraying Systems
Spraying Systems TeeJet TECHNOLOGIES BoomPilot Manual de usuario
Spraying Systems
Spraying Systems TeeJet BOOMPILOT Manual de usuario
Spraying Systems
Spraying Systems 1550+ AutoJet Manual de usuario
Spraying Systems
Spraying Systems TeeJet Technologies 744E Manual de usuario
Spraying Systems
Spraying Systems TeeJet 845 Manual de usuario
Spraying Systems
Spraying Systems AutoJet SCS Series Manual de usuario
Spraying Systems
Spraying Systems TeeJet TECHNOLOGIES BoomPilot Manual de usuario
Spraying Systems
Spraying Systems TeeJet 844-E Manual de usuario
Spraying Systems
Spraying Systems TeeJet TECHNOLOGIES BoomPilot Manual de usuario
