Split Phantom ULB21 Guía rápida

PLIT390 REV. F 10/16/12

INSTALLATION AND INSTRUCTION MANUAL

IMPORTANT: Please read all of the following instructions before installing your new warning light.

The Split Phantom

™

Underc ver Interi r LED Lightbar

M dels

ULB21 ULB24

(Discrete) (Gen 4 Starburst)

-1-

The Split Phantom

™

uses state-of-the-art Light Emitting Diode (LED)

technology. This warning light is comprised of ultra-high intensity LEDs that

are operated by a micro-controller to efficiently produce light output with

lifetimes up to 1 , hours.

IMPORTANT: Please read all of the following instructions before installing your new

Split Phantom

™

LED undercover lightbar.

CAUTION: Please be sure to check that your cigarette plug outlet is properly fused. Testing the

light bef re this fuse is pr perly installed will v id the warranty n the light.

WARNING!!!! Care should be taken when positioning this warning light so that the light and/or

cord does not interfere with the proper operation of the driver-side or passenger-

side airbag! Failure to heed this warning may result in serious or fatal injury.

Please Note: These instructi ns are pr vided as a general guideline nly. Specific

m unting and/ r wiring, may be necessary and are the s le resp nsibility f the

installer. Star Headlight & Lantern C ., Inc. assumes n resp nsibility f r the

integrity f the installati n f r this r any f its pr ducts.

CAUTION: All of our DC powered warning lights are polarity

sensitive. These lights are polarity protected only if the

appropriate fuse is used. All wires connected to the positive

terminal of the battery should be fused at the battery for their

rated load. Testing the light bef re this fuse is pr perly

installed will v id the warranty n the light.

NOTICE

Due to continuous product improvements, we must reserve the right to change any

specifications and information, contained in this manual at any time without notice. Star

Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual,

including, but not limited to, the implied warranties of merchantability and fitness for a particular

purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained herein or for

incidental or consequential damages in connection with the furnishing, performance, or use of

this manual.

-2-

Optional Mountin Brackets

There are several optional mounting brackets that can be used to mount your

Split Phantom

™. Your light comes with the one that was selected at the time

the light was ordered.

274-ULB21-U1 Universal Mounting Kit

274-ULB21-CH 2 6-2 1 Dodge Charger

2 7-2 8 Dodge Magnum

2 9 Dodge Ram

274-ULB21-CH11 2 11 Dodge Charger

274-ULB21-CP 2 11 Chevrolet Caprice

274-ULB21-CV 2 6-2 11 Ford Crown Victoria

2 9 Ford F15 and F25

274-ULB21-EX 2 6-2 1 Ford Explorer

2 7-2 1 Ford Expedition

274-ULB21-IM 2 8-2 1 Chevrolet Impala

274-ULB21-INT 2 12 Ford Interceptor (Taurus)

274-ULB1 -RM 2 12 Dodge Ram 15

274-ULB21-TA 2 7-2 11 Chevy Tahoe

2 7-2 11 Chevy Yukon

2 7-2 11 Chevy Suburban

tar Headlight & Lantern Co., Inc. assumes no

responsibility for the secure mounting of this light. It is the

responsibility of the installer and/or owner to ensure the

lightbar is mounted securely. Check your light every time

you enter the vehicle to ensure that it is mounted securely.

Please Note: Every ULB21 comes with a standard baffle included. The 274-ULB21-CH

and 274-ULB21-CH11 kits also include a separate baffle that is specifically designed to

fit the Dodge Charger. It should be used in place of the standard baffle included.

-3-

The

Split Phantom

™ is desi ned to be mounted on the inside

of your vehicle. It is not intended for exterior applications and is

not warranted a ainst water dama e.

It is the sole responsibility of the owner to ensure the warning light is

secure. Check your light every time you enter the vehicle to ensure that

it is mounted securely. The manufacturer assumes no responsibility for

the secure mounting of this light.

The following mounting instructions describe the standard, most

common way to mount this light. This method may or may not apply to

your vehicle. Because vehicles can vary widely in their design, it may be

necessary to configure the brackets differently than described. Some

applications may require you to design your own custom brackets. The

installer assumes all responsibility for the integrity of the installation. It is

the sole responsibility of the owner to ensure the li ht is secure.

Mountin Instructions

Before installing any of the

brackets, slide the enclosed

rubber channel over the

front edge of the baffle .

The ULB21 is designed to be mounted in the front windshield of a vehicle using

both of the pre-existing visor clips. An alternate method is also shown using the

Universal Brackets.

-4-

SUCTION CUP

WINDOW ADHESIVE

MOUNT

UNIVERSAL BRACKET INSTALLATION

(Model 274-ULB21-U1)

•

Two different sets of forked brackets are provided. Use the pair of forks

that will require the least amount of adjusting when aligning the light with

the window.

•

The Universal Mount uses either pair of forked brackets, in conjunction

with either a pair of suction cups or a pair of window adhesive mounting

pads (both included).

•

The Forked Brackets must be installed for both the suction cup and

window adhesive mounts.

•

Determine if you can install the Forked Brackets under your visor clips or

if you need to attach them in an alternate fashion and refer to the

appropriate section on pages 6 or 7.

The mountin instructions are divided into two separate sections. If you

are usin the Universal Mount, proceed below. If you will be usin one of

the vehicle specific brackets, please skip to pa e 9.

-5-

CAUTION: Take extreme caution not to over ti hten the screws!!! Over

ti htenin of the screws can strip the holes.

1. Insert one of the carriage

bolts through one of the

washers. Please note that

washer is used as a spacer

on the square neck of the

carriage bolt. Slide the bolt

and washer through the

back of the left bracket.

Be sure to select the correct

bracket. The larger flange

should be located towards

the center of the light.

2. Remove three of the #8 x 1/2" self-

tapping Phillips pan head screws and

use them to install the left attaching

bracket on the light.

CAUTION: Take extreme caution not

to over ti hten the screws!!! Over

ti htenin of the screws can strip the

holes and result in a faulty mount.

3. Once the left attaching bracket is installed

securely on the light, fasten one of the

forked “L” brackets to the attaching

bracket, using the carriage bolt,

a washer, and a nut. Leave

the nut slightly loose to

allow for minor adjustments

during the remainder of the

installation.

Attach Forked Brackets to Li ht

4. Repeat steps 1-3 for the right attaching bracket

Universal Mountin (CONT'D)

-6-

1. Standard mounting uses the factory

installed visor clips already located on

the vehicle, in conjunction with the

suction cups or window adhesive

mounts. If you do not have any visor

clips, use the Alternate Mountin

section on the next page

2. Locate the two visor clips on the vehicle.

The style may vary from vehicle to vehicle.

Some styles use only one screw each,

while others may have more. Verify that

both visor clips are a minimum of 3” from

the center of the window, and a maximum

of 8” from the center.

3. Loosen (or remove if necessary) both visor

clips enough that one of the forked brackets

can easily slide under each of them.

4. Slide one forked bracket under each visor clip

and tighten the clip such that it securely holds

each bracket in place.

Bend here if

necessary

5. Once the brackets are installed securely under the visor clips or with a suitable

fastener, check to see that the bottom of the light is level front-to-back. If it is

not level, remove the light from the visor clips and carefully bend the forked

brackets as necessary. Reinstall the light and check again for levelness.

Repeat this process until the light is level.

Attach Forked Brackets to Visor Clips

(If you do not have visor clips, or your visor clips will NOT provide a secure mount, or this

method will not work in your vehicle for any other reason, use the alternate method on the

next page.)

Universal Mountin (CONT'D)

-7-

Attach Forked Brackets usin Alternate Method

If you are not using the visor clip installation described on the previous page,

continue below.

1. Some vehicles may not have visor clips appropriate for the previously

described installation, or may completely lack any visor clips. An alternate

mounting screw hole is provided in the bracket for these situations. This hole

can be used with an appropriate user supplied screw or other suitable fastener.

2. If you are using the alternate mounting screw hole, you will need to locate the roof

brace under the headliner of the vehicle.

3. Once you have located the roof brace, pick an area to mount the brackets (one on

each side) that is a minimum of 3” from the center of your window and a maximum

of 8”.

4. You must then determine an appropriate size screw to penetrate the headliner and

securely mount the brackets to the roof brace. When selecting a screw, take care to

ensure that it is capable of supporting the weight of the light and it will not penetrate

the roof of the vehicle.

5. Carefully drill any necessary pilot holes in your roof brace. CAUTION: Take care to

ensure when selectin a screw and drillin the hole that it is capable of

supportin the wei ht of the li ht and that it does not penetrate the roof of the

vehicle.

6. Install the screws through each bracket.

7. If necessary, adjust your light as described in Step 5 on the previous page.

Alternate

Mounting

Hole

Universal Mountin (CONT'D)

-8-

Universal Mountin (CONT'D)

2. Use the screws to attach the

"L"-Brackets to either end of

the light as pictured to the

right. You may desire to

remove the nylon spacer if

the screw does not securely

fasten to the base.

CAUTION: Take extreme

caution not to over ti hten the

screws!!! Over ti htenin of

the screws can strip the holes

and result in a faulty mount.

Rem ve uterm st screws

fr m b tt m f unit.

(Bottom View)

Attach The Suction Cups or Window Adhesive Mounts

1. Remove the two #4 x 1/4" Phillips pan head screws on either end of the bar,

along with the washers and nylon spacers.

3. Then use the appropriate hardware (as shown above) to attach either the

Adhesive Pads or the Suction Cups, depending upon your application.

If using the window adhesive:

•

Be sure to use the tube of cleaner to clean both surfaces.

•

After applying adhesive, please allow a minimum of 2-5 minutes

for the pad to adhere to the window before releasing pressure.

•

Allow 24 hours for the adhesive to fully cure before using.

4. Continue to the BAFFLE ADJUSTMENT section on page 11.

-9-

VEHICLE SPECIFIC BRACKET INSTALLATION

(All optional brackets excludin the 274-ULB21-U1)

Determine which bracket style y u have, T p M unt r Rear M unt.

Depending upon which vehicle specific bracket you ordered, there are two

different ways the bracket can attach to the light. One style mounts to the top of

the light, one style mounts to the back of the light.

TOP MOUNT

REAR MOUNT

T p M unt

1. Mount the visor bracket to the

light.

2. Mount the light and bracket

assembly to the visor clips.

Rear M unt

1. Mount the visor bracket to the

visor clips.

2. Mount the angled bracket to the

visor bracket.

3. Mount stud brackets to light.

4. Mount the light and bracket

assembly to the visor clips

The mounting procedure differs slightly between the two brackets:

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario