Splash Lab TSL.C.060 Guía de mantenimiento y servicio
TSL 060.C.
channel hand dryer
installation + maintenance
contents
3 Safety and Warnings
4 Box Contents
5 Technical Data
6 BeforeYouInstall
8 HowtoInstall
13 Commissioning
15 Operation
15 Maintenance
16 Cleaning
17 Troubleshooting
18
18
Diagram
Spare Parts / Accessories
19 Warranty
BackCover ContactDetails
2 + TSL.C.060 CHANNEL HAND DRYER MANUAL
Read and save these instructions
WARNING !
TSL.C.060 CHANNEL HAND DRYER MANUAL + 3
General information
310 410 5008
Technical support
info@thesplashlabusa.com
For further contact information visit:
www.thesplashlabusa.com
Warehouse + Offices:
20809 Higgins Court, Torrance CA 90501
Showroom:
8745 Washington Boulevard, Studio D, Culver City CA 90232
TSL.C.060 channel hand dryer
To reduce the risk of fire, electric shock or injury to persons, observe the following:
+ Use this unit only in the manner intended by the manufacturer. If you have any
questions contactthemanufacturer(seebackpagefordetails).,
+ This equipment should be installed in a way that ensures all electrical parts are
keptdry.
+ A means of electrical isolation must be incorporated in the fixed wiring, in
accordancewiththecurrentlocalregulationsinforce.
+ Disconnectthepowersupplybeforeperforminganymaintenanceontheproduct.
+ Childrenshouldnotplaywiththisequipment.Cleaningandmaintenanceshallnot
beperformedbychildrenwithoutsupervision.
+ Thisequipmentisdesignedtobeusedincommercialandpublicareas;itisnot
intendedfordomesticorresidentialuse.
+ Ensurewiringandcoverisinstalledcorrectlybeforeconnectingtolivepower
supply.
+ Ifindoubt consultanelectrician.,
+ Thisproductisnotintendedforuseinadomesticorresidentialapplication.
+ Thedryermustbeinstalledinaccordancewiththeelectricalinstallation
regulationsinforceatthetimeofinstallation.
+ Thehanddryermustbegrounded.
A Dryerheadassembly
B Hand dryer motor unit
C Power cable
D Pad
E Gasket
F Washer
G Fixing nut
H Angled pipe
I Motor mounting screws
J
K
Hex wrench
Air hose
boxcontents
A
C
B
J
ID
E
F
G
K
4 + TSL.C.060 CHANNEL HAND DRYER MANUAL
H
Current 7.6-8.4A
Powerconsumption 0.84-1.0kW
Standbypower 0.3-0.4kW
Dryingtime <15seconds
Weight 17lb
Material AISI316stainlesssteel
Noiselevels 68.6dB
Heatingelement 500W
Motortype Brushtype;dualballbearings;
Motorpower 500 - 350W
Airspeed 364ft/s
Airflow 27.6cuft/min
Sensorrange 5"+/-1"
technical data
Finishes TSL.C.060.C
TSL.C.060.CS
TSL.C.060.CP
TSL.C.060.BK
TSL.C.060.BR
Voltage 110-120V ac; 60Hz
Securitycut-of f time 60seconds
Motorthermalprotection Autoresettingthermostatsetat203°F
Heaterthermalprotection Autoresettingthermostatsetat185°F
Thermalcutoutfusesetto288°F
Insulation Class1
IPrating IP35
Approvals CE UL cUL, RoHS, ADA,,
Warranty1 year parts and labor
Filter 3M filter assembly (HEPA filter is available for this
product, please enquire for technical information)
Bright Polished
Brushed Stainless
Brushed Copper
Brushed Black
Brushed Brass
TSL.C.060 CHANNEL HAND DRYER MANUAL + 5
before you install
Basins
The Splash Lab Monolith (Series C or D)
basin isrecommendedforusewiththe
Channel rangeofproducts. If an alternative
basin is used, please confirm with
The Splash Lab that there will be no
reflection or splash issue.
Powersupply
A15Afusedsupplymustbeprovidedfor
connectiontothemainspowersupply.
Spacing
If the Channel Hand Dryer is installed with
other units from the Channel range, the
Channel Faucet, which is at the center,
should be 8" to the left of the Hand Dryer.
The Channel Soap Dispenser should be 6"
to the left of the Faucet.
Location
Disclaimer:Circuitsshouldonlyuse
80%oftheirgivenamperagetoprevent
overloads.ThestandardUS120V15Amp
circuitshouldonlyuseupto12ofits15
amps.
6 + TSL.C.060 CHANNEL HAND DRYER MANUAL
Channelhanddryersaresuppliedwith48"
offlexiblehose,sothedryermotorunit
mustbefittedwithin48"oftheheadunit,
toensurethatthemotorair-outlethead
canbeconnected.
The Splash Lab offers an optional backplate
for the fixtures that means the fixtures can
be mounted from the front and have simpler
access.
Backplate
6"8"
Back wall
Fixture insert
Washbasin
Front view
Ø 7/8"
Soap Faucet Dryer
Ø /"
1316
Ø "
1 3/16
8"MIN
10"MAX
Distance between
the sensor and
the bottom of the basin
FIXING
before you install
SIDEFRONT
2 "
9-5/16"
10-3/4"
12-1/16"
7-9/16"
5-7/8"
110-120V / 15A plug
51-3/16"
TSL.C.060 CHANNEL HAND DRYER MANUAL + 7
Default
Sensor
Range
3/4" - 5-1/8"
48"
23-5/8"MIN
39-3/8"MAX
how to install
1 2
Fit dryer body into the 1 3 16" hole in wall.- /
Ø -/"1 3 16
8 + TSL.C.060 CHANNEL HAND DRYER MANUAL
Drill hole 1 3 16" diameter in wall 8-10" - /
above the bottom of the basin.
When step 3 is finished, run the sensor wire
and ground wire through angled pipe and fix
it to the fixing nut.
43
Thread the sensor and cables ground
through the gasket, washer and
fixing nut, and tighten the nut
against the installation wall.
TSL.C.060 CHANNEL HAND DRYER MANUAL + 9
how to install
Fit the dryer motor unit to wall or cabinet,
within 48" of the dryer nozzle already
installed in the wall.
6
10 + TSL.C.060 CHANNEL HAND DRYER MANUAL
Remove cover-fixing screws from
underside of dryer motor using the
security hex key provided, and then
remove the cover.
5
Este manual sirve para los siguientes modelos
5
Tabla de contenidos
Otros manuales de Secadora de Splash Lab
Manuales populares de Secadora de otras marcas
Indesit
Indesit IDV 75 Manual de usuario
Infiniton
Infiniton SD-DG85C Manual de usuario
BOMANN
BOMANN WT 5019 Manual de usuario
Alliance Laundry Systems
Alliance Laundry Systems TMB795C Manual de usuario
Asko
Asko T793C Manual de usuario
Kenmore
Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Manual de usuario