Sper scientific 800201 Manual de usuario
1
Thermal Imaging Camera
220 x 160
800201
Instruction Manual
2
TABLE OF CONTENTS
INTRODUCTION ................................................................ 3
FEATURES.......................................................................... 4
MATERIALS SUPPLIED .................................................... 4
FRONT PANEL DESCRIPTION......................................... 5
LCD DISPLAY ..................................................................... 6
SET UP................................................................................ 7
MEASUREMENT PROCEDURES................................... 12
IMAGE DOWNLOADING ................................................. 14
CARE AND MAINTENANCE............................................ 18
SPECIFICATIONS ............................................................ 19
WARRANTY ...................................................................... 20
3
INTRODUCTION
This Sper Scientic Thermal Imaging Camera (model
800201) combines a high precision thermal image with a
standard photo for maximum clarity. With the press of a
button, the thermal image can be blended in increments
of 25% on a beautiful 3.5” full color display. Five available
thermal color palettes and an impressive 35,200 pixel
resolution ensure the images are crystal clear and
can easily be placed in reports and presentations. The
Minimum, Maximum, and Spot values update in real-time,
allowing you to scan an area for changes without the
need to switch modes. A simple intuitive keypad allows
you to begin using the camera immediately, without overly
complicated keystrokes.
4
FEATURES
• Separate IR and Visible light cameras
• Attached ip-up lens cover for protection
• User-dened crosshair pinpointing
• Minimum and Maximum values
• Adjustable emissivity
• 0.5m focal length
• Rechargeable Lithium ion battery
MATERIALS SUPPLIED
• Thermal Imaging Camera
• Carrying Case with Strap
• Lithium ion battery
• Micro USB cable
• Instruction manual
5
FRONT PANEL DESCRIPTION
123 4
5
6
7
8
1. POWER Button
2. MENU Button
3. SELECT Button
4. ENTER Button
5. RIGHT Arrow/ Visual Image Toggle
6. DOWN Arrow
7. LEFT Arrow
8. UP Arrow/ MIN/MAX Toggle
6
LCD DISPLAY SETUP
1. Current Temperature of Crosshair
2. Minimum Temperature Location (Green Square)
3. Maximum Temperature Location (Red Square)
4. Current Maximum and Minimum Values
5. Battery Level Indicator
6. Emissivity Indicator
7. Color Palette Indicator
8. Crosshair Location
9. Time
7
1
2
3
4 9
6 5
8
7
Battery Installation
This camera comes with a Lithium ion battery already
installed inside the handle. The battery does not need to be
removed for charging.
TO CHARGE THE BATTERY
1. Flip open the door on the Left Hand side of the camera to
expose the Micro USB port.
2. Plug in the included micro USB Cable, ensuring the cable
seats fully.
3. Attach the USB end of the cord to a computer or any USB
wall charger.
4. Power cubes typically used to charge cell phones are safe
to use with this camera.
5. The charging icon will appear in the upper right corner of
the screen.
TO REPLACE THE BATTERY
Note…
Before replacing the battery, turn the camera o.
1. Ensure the replacement battery is a direct replacement
from Sper Scientic. This battery is custom made and
substitutions can damage the camera.
2. Hold the camera rmly in your palm with the trigger facing
up and away from your body.
3. Using steady pressure, press the rubber portion of the
handle straight down. The rubber portion is the removable
battery cover.
4. While pressing down, slide the battery cover away from
the handle. The cover will click once.
5. Push the battery cover again and it will easily come o
with a second click.
8
6. Remove the battery body and gently pull the four-wire plug
from the circuit board.
7. Plug the new battery into the pins of the exposed circuit
board. Ensure the black wires align with the negative (-)
pins and the red wires align with the positive (+) pins.
8. Slide the rubber piece back onto the handle until it
clicks twice.
9. Charge the camera for a minimum of two hours.
Power On and O
1. Press and hold POWER to turn the camera on.
2. The camera may take up to 5 seconds to turn on. This
is normal.
3. Press and hold POWER until “Power o” displays on
the screen. The camera will turn o after a ve second
count-down.
SETTING THE DATE AND TIME
1. Turn the camera on.
2. Press MENU.
3. Press the DOWN arrow to highlight Settings.
4. Press the RIGHT arrow to expand Settings.
5. Press DOWN to highlight Time format.
6. Press the RIGHT arrow to expand the Time format.
7. Use the UP and DOWN arrows to highlight your preferred
time format. The camera supports military (24 hr) or AM/PM.
8. Press SELECT to conrm your choice.
9. Press LEFT to exit to the previous screen.
10. Press DOWN to highlight Set Time.
11. Press the RIGHT arrow to expand Set Time.
9
12. Press SELECT in the rst box to change the Year.
13. Use the ARROWs to change the Year.
14. Press ENTER to accept the Year.
15. Use the DOWN arrow to scroll to the Month.
16. Press SELECT to expand Month.
17. Use the ARROWS to change the Month.
18. Press ENTER to accept the Month.
19. Repeat steps 15 - 18 for the Day, Hour, Minute,
and Seconds.
20. The camera will return to the previous settings mode
after the Seconds have been entered.
21. Press MENU to return to normal Camera Mode.
Note…
The Date and Time must be entered in military format,
regardless of the time format setting you select (For
example, 6pm must be entered as 18:00:00). Once in
measuring mode, AM/PM will populate if it was the time
format you selected.
SETTING THE TEMPERATURE UNITS
1. Turn the camera on.
2. Press MENU.
3. Press the DOWN arrow to highlight Settings.
4. Press the RIGHT arrow to expand Settings.
5. Press DOWN to highlight ”°C Unit.”
6. Press RIGHT arrow to expand Unit.
7. Use UP and DOWN to highlight your preferred choice.
8. Press SELECT to conrm your choice.
9. Press ENTER to exit to the previous screen.
10. Press MENU to exit to normal Camera Mode.
10
SETTING THE EMISSIVITY
1. Turn the camera on.
2. Press MENU.
3. Press the DOWN arrow to highlight Emissivity.
4. Press the RIGHT arrow to expand Emissivity.
5. Press the DOWN arrow to highlight your choice.
6. Press ENTER to conrm your choice or SELECT to enter
a custom value.
7. The camera will return to the previous settings page.
8. Press MENU to return to normal Camera Mode.
CHOOSING THE COLOR PALETTE
1. Turn the camera on.
2. Press MENU.
3. Press the DOWN arrow to highlight Color Palette.
4. Press the RIGHT arrow to expand Color Palette.
5. Use the UP and DOWN arrows to highlight your choice.
6. Press ENTER to conrm your choice.
7. The camera will return to the previous settings page.
8. Press MENU to return to normal Camera Mode.
Tabla de contenidos
