Sony RM-AV2000 Operating Instructions (primary... Manual de usuario

3-861-979-11(1)

Integrated Remote

Commander

Operating Instructions

RM-AV2000

For the customers in the U.S.A.

INFORMATION

This equipment has been tested and

found to comply with the limits for a

Class B digital device, pursuant to Part 15

of the FCC Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

The equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does not

cause harmful interference to radio or

televison reception, which can be

determined by turning the equipment off

and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving

antenna.

•Increase the separation between the

equipment and receiver.

•Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

•Consult the dealer or an experienced

radio/TV technician for help.

You are cautioned that any changes or

modifications not expressly approved in

this manual could void your authority to

operate this equipment.

Features

The RM-AV2000 Remote Commander provides centralized control of all your AV

components from a single remote commander and saves the trouble of operating

different AV components with different remote control devices. The following are its

main features.

Centralized control of Sony AV components with this one remote commander

This Commander is preset at the factory to operate Sony brand components, so you can

use it out of the box as a control center for your SonyAV components.

Remote control signals for non-Sony components are also preset

This Commander is preset for most major brands components including Sony. You can

remote control your components by setting their code numbers.

Learning function for programming other remote control signals you need

This Commander has a learning function, to learn remote control signals to operate

non-preset components or functions. In addition, the Commander can learn remote

control signals (infrared signals only) of non-Audio Visual components such as air-

conditioners, lights, etc. (some specific appliances or functions may not be available).

Adding or reassigning new components

You can use the OPTION button as an extra Component Select button. What’s more,

you can assign other Component Select Buttons to freely operate other components.

This is useful when you have more than two of the same kind of AV components.

System Control function allows one-touch operation to execute a series of

commands

You can program up to 16 consecutive operation steps to execute a series of operations

by pressing a single button.

Easy-to-operate touch key LCD with blue back light

This Commander has a touch key LCD that changes the key display according to the

selected component. The Commander is easy to operate as only the keys necessary to

operate the selected component are displayed. The display backlight allows operation

even in the dark.

Table of Contents

Getting Started

Installing the Batteries ......................................................................................................... 6

When to replace the batteries.............................................................................................. 6

Location and Function of Controls ....................................................................................... 7

Basic Operations

Setting the Code for PresetAudio and Visual Components ................................................. 8

Setting a Component Code ................................................................................................. 8

Checking if the code number works ................................................................................ 10

Operating Your Components with the Remote Commander .............................................. 11

Using Non-Preset Remote Control Operations — Learning Function ................................ 13

Changing or erasing the function of a learned key or button...................................... 16

Using the OPTION button ................................................................................................... 17

Advanced Features

Controlling theVolume of Visual Components Connected to anAudio System................. 18

Executing a Series of Commands — System Control Function .......................................... 20

Programming a series of commands to the SYSTEM CONTROL buttons ................ 20

Executing the programmed commands .......................................................................... 22

Changing the programmed commands .......................................................................... 23

Adding an Extra Function to the Component Select Buttons............................................. 24

Programming the Power-On Command of the Selected Component (for Sony

Components only) ........................................................................................................... 24

Adding a Command that is Required when Selecting a Component ........................ 25

Turning Off the Power of All Components by a Single Button Operation

— System Power-Off Function (for Sony Components only) ........................................... 26

Assigning Other Components to the Component Select Buttons ...................................... 27

Programming a Frequently Used Key Operation to SYSTEM CONTROL Buttons ................ 29

Using Other Functions

Locking the Controls — Hold Function............................................................................... 30

Protecting your settings and “learned” signals — Preset Lock Function .......................... 31

Changing theAuto Power-Off Time of the Commander ..................................................... 32

Adjusting the Backlight of the Display Window ................................................................. 33

Additional Information

Precautions ......................................................................................................................... 34

Maintenance ....................................................................................................................... 34

Specifications...................................................................................................................... 34

Troubleshooting .................................................................................................................. 35

Appendix

Table of Preset Functions.................................................................................................... 37

TV.......................................................................................................................................... 37

VCR 1, 2, 3............................................................................................................................ 37

DVD ...................................................................................................................................... 38

VD (LD player) ................................................................................................................... 38

DBS ....................................................................................................................................... 39

CBL (Cable box) .................................................................................................................. 39

AMP...................................................................................................................................... 40

CD ......................................................................................................................................... 40

MD ........................................................................................................................................ 41

DAT....................................................................................................................................... 41

DECK B/A ........................................................................................................................... 42

TUNER ................................................................................................................................. 42

DSP (Digital Surround Processor).................................................................................... 42

LCD Touch Key DisplayTable ............................................................................................... 43

Quick Reference of Operations........................................................................................... 51

Index ......................................................................................................................back cover

Getting Started

Installing the Batteries

Slide open the battery compartment lid

and insert six size AA(R6) batteries (not

supplied). Be sure to line up the + and -

on the batteries with the + and - on the

battery compartment.

When to replace the batteries

Batteries for remote control

operation (Four size AA (R6)

batteries)

Under normal conditions, batteries will

last up to six months. If the Commander

does not operate properly, batteries

might be worn out and iis displayed

on the LCD touch panel. When the

display dims, replace the batteries with

new ones.

Note

• Do not take more than one hour to replace

the batteries; otherwise, your setting of the

code numbers (page 8) and learned remote

control signals (page 13) will be erased.

Batteries for backlight (Two size

AA (R6) batteries)

When the backlight for the touch keys

grows dim, replace its batteries.

Notes on batteries

• Do not mix old batteries with new ones or

mix different types of batteries together.

• If the electrolyte inside the battery should

leak, wipe the contaminated area of the

battery compartment with a cloth and replace

the old batteries with new ones. To prevent

the electrolyte from leaking, remove the

batteries when you plan not to use the

Commander for a long period of time.

(for backlight) (for remote control

operation)

}

}]

}

]

}

]

}

]

}

]

SYSTEM CONTROL COMMANDER

OFF

LIGHT

TV VCR1 VCR2 VCR3 DVD DBS/CBL

AMP CD MD/DAT DECK B/A TUNER OPTION

CHANNEL VOLUME

MUTING

–

≠

123

!º

5COMMANDER OFF button

Turns the power of the Commander

off.

6Component Select buttons

Selects the component to control.

7OPTION button (page 17)

You can assign this button to operate

any component and use it as a

Component Select button.

8VOLUME +/– buttons*

Adjust the volume.

9MUTING button*

Mutes the volume.

0CHANNEL +/– buttons

Select the channel.

* The Commander controls or mutes the TV’s

volume when you select a visual component.

The Commander controls or mutes the

amplifier’s volume when you select an audio

component.

You can change this setting also (page 18).

Note on the power on and off of the

Remote Commander

To turn on the power, press any button except

the COMMANDER OFF button.

To turn off, press COMMANDER OFF, or if

you don’t use the Commander, it automatically

turns off after 10 minutes. This interval can also

be changed (page 32).

To turn off the key touch

confirmation beep

Press the ≥key. “OFF” is displayed and the

Commander no longer makes the key touch

confirmation beep. To switch the key touch

confirmation beep back on, press the ≥key

again.

Location and Function

of Controls

1Component display area

Displays the name of the component

selected.

2LCD touch key display

The keys used for operating each

component are displayed.

Note

Do not press the touch keys using sharp

objects such as pins or ball-point pens.

3SYSTEM CONTROL buttons (page

20)

You can program up to 16 consecutive

key operations to each of the three

SYSTEM CONTROL buttons . You can

automatically carry out the entire

program by pressing one button.

4LIGHT button

Used to light up the LCD display in

the dark. Press the button once to turn

on the light, and once again to turn it

off. You can also set the backlight to

go off automatically after a certain

period of time (page 33).

SYSTEM CONTROL COMMANDER

OFF

LIGHT

TV VCR1 VCR2 VCR3 DVD DBS/CBL

AMP CD MD/DAT DECK B/A TUNER OPTION

CHANNEL VOLUME

MUTING

–

≠

123

456

+10

ENTER

DISPLAY

Example: To set up a Philips’ TV

1See the tables in the supplied

“Component Code Numbers”,

and find the double digit code

number for the desired

component.

If more than one code number is

listed, use the number that is listed

first.

For example, to set up a Philips’ TV,

you would use the code number 11.

2While pressing COMMANDER

OFF, press MUTING.

All the component names in the

display flash.

Basic Operations

Setting the Code for

Preset Audio and Visual

Components

The Commander is preset at the factory

to operate Sony brand AV components

(see the table below). If you are using the

Commander with a factory-set Sony

components, skip the following

procedures.

You can use the Commander with other

preset AV components also. To use with

other AV components, you need to follow

the procedures to set the correct codes for

each component.

COMMANDER

OFF MUTING

TV VCR123 DBS TUNER

CBL CD OPMD DECKAMP DVD AB

* Analog audio compact cassette deck

Component

Select

Button

VCR1

VCR2

VCR3

DVD

DBS/CBL

AMP

MD/DAT

DECK B/A

TUNER

OPTION

Factory setting

Sony TV

Sony Beta VCR

(VTR1)

Sony 8mm VCR

(VTR2)

Sony VHS VCR

(VTR3)

Sony DVD

player

Sony DBS tuner

Sony amplifier

Sony CD player

Sony MD deck

Sony cassette

deck

Sony FM/AM

tuner

—

Preset

component(s)

VCR

DVD player

(DVD)/LD

player (VD)

DBS tuner

(DBS)/Cable

box (CBL)

Amplifier

CD player

MD deck/DAT

deck

Cassette deck*

FM/AM tuner/

Surround

processor

(You can preset

any of the

above.)

See “Table of Preset Functions” (page 37)

for the functions of keys and buttons as

for each component.

Setting a Component Code

5If you want to set a code for

another component, repeat Steps

3 and 4.

6Press COMMANDER OFF.

Notes

• If you press a component code number that is

not on the table in the supplied “Component

Code Numbers”, the Commander beeps and

“NG” flashes after you press the ENTER key.

If this happens,check the component code

number, and try setting again.

• If you don’t input anything into the

Commander for over two minutes between

each step, the setup procedure will be

canceled. To set the code, you must again

press MUTING while pressing

COMMANDER OFF.

To check which code number is

set

Press the DISPLAY key. The code number

and “ENTER” appear twice.

To set a component code on the

OPTION button

Assign a component to the OPTION

button first (see page 17), and then follow

the procedure on page 8 to 9.

3Press the Component Select

button* for the desired

component.

The selected component remains

displayed, and the 0 – 9, ENTER and

DISPLAY keys flash.

* When you set the component code of the

DVD or DBS/CBL button,press

repeatedly until the desired component is

displayed.

4Press the double digit component

code number followed by the

ENTER key on the touch-key

display.

A beep sounds, and the code numbers

and “ENTER” appear twice.

Continued

ENTER

COMMANDER

OFF

123

456

ENTER

VIDEO2

DISPLAY

ENTER

123

456

Setting the Code for Preset Audio

and Visual Components

(continued)

Checking if the code number

works

1Press the corresponding

Component Select button for the

component you have set up.

The Commander turns on and the

touch-keys appear on the display.

2Power on the component with its

power switch.

3Aim the Commander at the

component and press the POWER

key in the touch-key display.

When the remote control signal is

sent, is displayed on the display.

The component should power off.

4If you have succeeded, check that

the Commander is operating the

other functions of your

component, such as channel and

volume control.

See page 11 for details.

If the Commander does not seem to

be working...

Try repeating these setup procedures using the

other codes listed for your components (see

page 8).

Notes on keys which have

“learned” a remote control

signal already

If another signal has alreday been

programmed on that key or button by the

learning function (page 13), that

“learned” signal will work even after you

set the component code number. To use it

as a preset component key or button, first

erase its learned signal.

Note on the touch-key display

When you set a component code number,

only the keys that have been preset with

the signals for the desired component

will be displayed. Preset signal of each

key varies according to the brand.

By using the learning function, you can

program remote control signals to both

the displayed keys and keys that are not

displayed (see page 13).

POWER

123

456

ENTER

TV/VIDEO

RECALL

DISPLAY

POWER

EXECUTE

SLEEP

Otros manuales para RM-AV2000 Operating Instructions (primary...

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Mando a distancia de Sony

Sony

Sony Remote Commander RM-V40 Manual de usuario

Sony

Sony RM-V40 Manual de usuario

Sony

Sony RM-V210 - Universal Remote Manual de uso y mantenimiento

Sony

Sony RM-V201T Manual de usuario

Sony

Sony RM-VS10TV Manual de instrucciones

Sony

Sony RM-V3 Manual de usuario

Sony

Sony RM-946 Manual de usuario

Sony

Sony RMF-TX300E Manual de usuario

Sony

Sony RM-LG112 Manual de usuario

Sony

Sony RM-X4S Operating Instructions (primary... Manual de usuario

Sony

Sony RM-V8A Manual de usuario

Sony

Sony RMF-YD001 Manual de usuario

Sony

Sony RM-EZ2 Manual de usuario

Sony

Sony RM-V210T Manual de usuario

Sony

Sony RM-X55M Marketing Manual de usuario

Sony

Sony RM-IP500 Manual de usuario

Sony

Sony RM-DR1 Manual de usuario

Sony

Sony CECH-ZRC1U Manual de usuario

Sony

Sony Live-View Remote RM-LVR1 Manual de usuario

Sony

Sony RM-VL610A (RM-VL610A Remote Commander®) Manual de usuario

Sony

Sony RM-AX4000 - Integrated Remote Commander Instrucciones de montaje

Sony

Sony RM-V301 Manual técnico

Sony

Sony RM-V8 Manual de usuario

Sony

Sony RM-S2020K Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación