Sony DEP-100 Manual de usuario

DEP-100

DIGITAL EFFECTS PROCESSOR

INSTALLATION MANUAL

1st Edition

Serial No. 10001 and Higher

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

For the U.S.A

Attention-when the product is installed in Rack:

1. Prevention against overloading of branch circuit

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

make sure that the rack does not overload the supply

circuit.

2. Providing protective earth

When this product is installed in a rack and is

supplied power from an outlet on the rack, please

confirm that the outlet is provided with a suitable

protective earth connection.

3. Internal air ambient temperature of the rack

When this product is installed in a rack, please make

sure that the internal air ambient temperature of the

rack is within the specified limit of this product.

4. Prevention against achieving hazardous

condition due to uneven mechanical loading

When this product is installed in a rack, please make

sure that the rack does not achieve hazardous

condition due to uneven mechanical loading.

1 (E)

DEP-100

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 2 (E)

Contents ............................................................................................................... 2 (E)

Related manual .................................................................................................... 2 (E)

1. Installation

1-1. Installation Environment .......................................................................1-1 (E)

1-2. Power Supply ........................................................................................ 1-1 (E)

1-2-1. Power Specifications ............................................................ 1-1 (E)

1-2-2. Power Cord ...........................................................................1-1 (E)

1-3. External Dimensions and Installation Space ......................................... 1-2 (E)

1-4. Matching Connectors and Cables.......................................................... 1-3 (E)

1-5. Input and Output Signal of Connector .................................................. 1-4 (E)

1-6. Switch Setting on Connector Panel ....................................................... 1-7 (E)

1-7. Switch Setting on Board........................................................................ 1-7 (E)

1-8. Rack Mounting ...................................................................................... 1-8 (E)

2. Service Overview

2-1. Cleaning of Air Filter ............................................................................ 2-1 (E)

2-2. Periodic Replacement ............................................................................ 2-1 (E)

2-3. Information of LEDs on Board ............................................................. 2-2 (E)

2-4. ISR ......................................................................................................... 2-3 (E)

2-4-1. Functions Overview ............................................................. 2-3 (E)

2-4-2. Usage of ISR Functions ....................................................... 2-3 (E)

2-4-3. Supported Commands .......................................................... 2-4 (E)

2-4-4. Functions of Commands ...................................................... 2-4 (E)

2 (E) DEP-100

Purpose of this manual

This manual is the installation manual of the DEP-100 Digital Effects Processor.

This manual is intended for use by trained system and service engineers, and

describes the information regarding installation.

Contents

The following is a summary of all the sections for understanding the contents of this

manual.

Section 1 Installation

Explains the operating environment, the connector information for peripheral

equipment connections, etc.

Section 2 Service Overview

Explains the cleaning and summary of ISR.

Related manual

Besides this installation manual, the following manuals are available for the DEP-

100.

.Operation Manual (Supplied with the DEP-100.)

This manual explains the overview of the DEP-100, and the system configuration

examples.

.Maintenance Manual (Not supplied with the DEP-100.)

This manual describes the information that premise the service based on parts

replacement (adjustments, board layouts, schematic diagrams, parts list, etc.).

If this manual is required, please contact to Sony’s service organization.

Manual Structure

1-1 (E)

DEP-100

Section 1

Installation

1-1. Installation Environment

Operating temperature: +5 dC to +40 dC

Storage temperature: _20 dC to +60 dC

Operating humidity: 20 % to 90 % (non-condensing)

Do not install the DEP-100 in the following locations.

.Areas where the unit will be exposed to direct sun light

or any other strong lights.

.Areas near heat sources.

.Dusty areas or areas where it is subject to vibration.

.Areas with strong electric or magnetic fields.

.Areas where is subjected to electricity noise.

.Areas where is subjected to static electricity noise.

1-2. Power Supply

1-2-1. Power Specifications

Power requirements: AC 100 to 240 V

50/60 Hz

Current consumption: maximum 1.0 A (at 100 V)

maximum 0.5 A (at 240 V)

A switching regulator is used for the power supply of the

DEP-100. The voltage within the range of 100 V to 240 V

can be used without changing the supply voltage.

As the inrush current at turn-on is maximum 20 A (at 100

V)/maximum 40 A (at 240 V), the capacity of the AC

power must be adequate with the inrush current of maxi-

mum 20 A (at 100 V)/maximum 40 A (at 240 V).

If the capacity of the AC power is not the adequately large,

the breaker of the AC power at the supply side will operate

or the DEP-100 will abnormal operate.

1-2-2. Power Cord

To avoid a fire or an electric shock, be sure to use the

designated power cord. And do not damage to the power

cord.

For the customer outside of the area as shown above or in a

part of Europe, the above-mentioned power cords can not

be used.

Use the power cord that is applicable to the places in the

world.

1-557-377-01

AC inlet

Power cord for the customer in the U.S.A. and Canada.

1Power cord set

2Plug holder (Black) 2-990-242-01

Power cord for the customer in Europe except the

United Kingdom.

1DK-2401(AE) (approx. 2.4 m)

2Plug holder (Black) 2-990-242-01

Plug holder is included in DK-2401(AE).

Power cord for the customer in the United Kingdom.

1DK-2401(UK) (approx. 2.4 m)

2Plug holder (Black) 2-990-242-01

Plug holder is included in DK-2401(UK).

AC inlet

1-2 (E) DEP-100

1-3. External Dimensions and Installation Space

To prevent the temperature rise inside the DEP-100, pay careful attention to circulation of air in the place

where the DEP-100 is installed.

The rear side of the DEP-100 should be at least 20 cm away from walls for ventilation and maintenance.

1-3. External Dimensions and Installation Space

866.2

424

450

304.883.7

57.2

132.4 (3U)14.5

254

101.6

482

465

424

(Front view) (Right side view)

(Top view)

Front panel

Unit : mm

Mass : 13.5 kg

1-3 (E)

DEP-100

1-4. Matching Connectors and Cables

When connecting cables to various connectors on the rear panel at the time of installing or servicing,

connect the following connectors/cables or their equivalents.

DEP-100 Matching Connector/Cable

Panel indication Connector/cable Sony Part No.

ANALOG I/O BNC 75 Z, male 1-560-069-11

REF.VIDEO

MONITOR OUT

DIGITAL I/O BNC 75 Z, male 1-560-069-11

PROGRAM OUT 5C-2V cable *1—

DSK INPUT

SDI INPUT

MOUSE 9-pin serial mouse *2—

ISR D-sub 25-pin, male 1-566-356-11 (Solderless type)

1-564-747-11 (Solder type)

GPI BNC 75 Z, male 1-560-069-11

EFFECT

KEY ON

KEY OFF

REMOTE-OUT D-sub 9-pin, male 1-560-651-00 (Connector)

REMOTE-IN 1-561-749-00 (Shell)

RCC-5G/10G/30G cable *3—

*1: 5C-2V (Max.100 meters) Fujikura America Inc./Fujikura Europe Ltd.(FEL) or the equivalent.

*2: Commercial products

*3: Length of these cables are 5 m, 10 m and 30 m, respectively.

1-4. Matching Connectors and Cables

1-4 (E) DEP-100

1-5. Input and Output Signal of Connector

Input Connector

1REF. VIDEO BNC x2, in loop through connection

Outside reference video signal (black burst or composite sync)

0.3 V p-p, 75 Z, sync negative

4DSK INPUT

FILL BNC x1

Component digital (270 Mbps)

Conform to SMPTE 259M & ITU-R BT.656

KEY BNC x1

Component digital (270 Mbps)

Conform to SMPTE 259M & ITU-R BT.656

5SDI INPUT

MAIN BNC x1

Component digital (270 Mbps)

Conform to SMPTE 259M & ITU-R BT.656

SUB BNC x1

Component digital (270 Mbps)

Conform to SMPTE 259M & ITU-R BT.656

6GPI (EFFECT, KEY ON, KEY OFF)

BNC x3

GPI input for effect control

TTL Level, 10 k Z

Output Connector

2MONITOR OUT BNC x1

Analog composite video

1.0 V p-p, 75 Z, sync negative

3PROGRAM OUT BNC x4

Component digital (270 Mbps)

Conform to SMPTE 259M & ITU-R BT.656

1-5. Input and Output Signal of Connector

MAIN

SDI INPUT

SUBFILL

DSK INPUT

KEY1

PROGRAM OUT

ANALOG I/O

MONITOR OUT

DIGITAL I/O

ONOFF

75 Z

KEY OFFKEY ONEFFECT

GPI

REMOTE-OUT REMOTE-INMOUSE ISR

AC IN

541 2 3

7 9 !/

REF. VIDEO

1-5 (E)

DEP-100

Communication Connector

7MOUSE D-sub 9-pin connector (RS-232C interface)

Mouse control

8ISR D-sub 25-pin connector (RS-232C interface)

For ISR (Interactive Status Reporting)

9REMOTE-OUT D-sub 9-pin connector (RS-422A interface)

Remote control

!/ REMOTE-IN D-sub 9-pin connector (RS-422A interface)

Remote control

1-5. Input and Output Signal of Connector

1-6 (E) DEP-100

7MOUSE: RS-232C (D-sub 9-pin, Male)

Pin No. Signal

1 DCD; Data Carrier Detect (Input)

2 RXD; Received Data (Input)

3 TXD; Transmitted Data (Output)

4 DTR; Data Terminal Ready (Input)

5 FG; Frame Ground

6 DSR; Data Set Ready (Input)

7 RTS; Request to Send (Output)

8 CTS; Clear to Send (Input)

9 RI; Ring Indicator

8ISR: RS-232C (D-sub 25-pin, Female)

Pin No. Signal

1 FG; Frame Ground

2 TXD; Transmitted Data (Output)

3 RXD; Received Data (Input)

4 RTS; Request to Send (Output)

5 CTS; Clear to Send (Input)

6 DSR; Data Set Ready (Input)

7 SG; Signal Ground

8 DCD; Data Carrier Detect (Input)

9 to 19 NC

20 DTR; Data Terminal Ready (Input)

21 to 25 NC

9REMOTE-OUT: RS-422A (D-sub 9-pin, Female)

Pin No. Signal

1 GND

2 RM RX (_)

3 RM TX (+)

4 GND

5 SPARE

6 GND

7 RM RX (+)

8 RM TX (_)

9 GND

!/!/

!/ REMOTE-IN: RS-422A (D-sub 9-pin, Female)

Pin No. Signal

1 GND

2 RM TX (_)

3 RM RX (+)

4 GND

5 SPARE

6 GND

7 RM TX (+)

8 RM RX (_)

9 GND

(Male)

–External view –

(Female)

–External view –

13 1

25 14

(Female)

–External view –

96(Female)

–External view –

1-5. Input and Output Signal of Connector

Otros manuales para DEP-100

Tabla de contenidos

Otros manuales de Equipo de grabación de Sony

Sony

Sony RCD-W3 - Cd/cdr Recorder/player Manual de usuario

Sony

Sony HSR-J2009 Manual de usuario

Sony

Sony DSR-DU1 Manual de usuario

Sony

Sony ICD-PX232 Manual de usuario

Sony

Sony CFD-S550 - Cd Radio Cassette-corder Manual de usuario

Sony

Sony SRW-5000 Manual de usuario

Sony

Sony PCM-D100 Manual de usuario

Sony

Sony Walkman TCD-D100 Manual de usuario

Sony

Sony BVT-2000 Manual de usuario

Sony

Sony PFV-D10 Manual de usuario

Sony

Sony AWS-750 Manual de usuario

Sony

Sony SRMASTER SR-PC4 Manual de usuario

Sony

Sony XE-90 MkII Manual de usuario

Sony

Sony BKNW-25 Manual de usuario

Sony

Sony ICD-B25 Operating Instructions (primary... Manual de usuario

Sony

Sony PCM-D50 - Portable Linear Pcm Recorder Manual de usuario

Sony

Sony DNW-A25WS Manual de usuario

Sony

Sony XDCAM EX PMW-EX30 Manual de usuario

Sony

Sony XDCAM PDW-HD1500 Manual de usuario

Sony

Sony BDX-N1000 Manual de usuario

Sony

Sony TCM-4300 Manual de usuario

Sony

Sony RCD-W10 - Cd/cdr Recorder/player Manual de usuario

Sony

Sony DMX-R100 Manual de usuario

Sony

Sony XDCAM PMW-1000 Manual de usuario

Manuales populares de Equipo de grabación de otras marcas

KV2 Audio

KV2 Audio 500 Series Manual de usuario

Robotics Technologies

Robotics Technologies microBus-Cam II Manual de usuario

Seca

Seca 460 Manual de usuario

Cognex

Cognex MVS-8000 Series Manual de usuario

Mect

Mect MPNC006 Series Manual de usuario

Bad Caf

Bad Caf THE LEASH Manual de usuario

Strymon

Strymon NIGHTSKY Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manual de usuario

Tews Technologies

Tews Technologies TPMC465 Manual de usuario

Honeywell

Honeywell Excel 50 Manual de usuario

SeaLevel

SeaLevel COMM+8.LPCI Manual de usuario

Arturia

Arturia AUDIOFUSE STUDIO Manual de usuario

Rukra

Rukra RK-1240 Manual de usuario

Samson

Samson SCOM Manual de usuario

Dynacord

Dynacord DPS260 Manual de usuario

Nice

Nice Core Manual de usuario

Pyle Pro

Pyle Pro PSS8 Manual de usuario

RF-System

RF-System TinyGate Manual de uso y cuidado