Sony VPL VPL-HW15 Manual de usuario
VIDEO PROJECTOR
VPL-HW15
PROTOCOL MANUAL
1st Edition
VPL-HW15
!警告
このマニュアルは，サービス専用です。
お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
1
VPL-HW15
Table of Contents
1. Overview
1-1. Introduction ........................................................................ 1
1-2. Glossary of Terms .............................................................. 1
1-3. Protocol Stack Structure..................................................... 1
2. Common Commands
2-1. Sub Commands .................................................................. 2
2-1-1. ITEM List ................................................................. 2
2-1-2. Infrared Remote Command Code............................. 6
2-2. Reply .................................................................................. 8
3. RS-232C
3-1. Connection ......................................................................... 9
3-2. Communication Specifications........................................... 9
3-3. Communication Procedure............................................... 10
3-4. Command Block Format ...................................................11
3-4-1. Simplified Command ...............................................11
3-5. Packet Examples .............................................................. 12
3-5-1. Change “Wide Mode” to “Zoom”........................... 12
3-6. AMX Device Discovery................................................... 12
1
VPL-HW15
RS-232C
Simplified Command
Asynchronous
Sub Command
1. Overview
1-1. Introduction
The projector is remotely controllable over RS-232C. It is useful for setting up the projector away from
the operator.
This protocol manual describes the specifications such as packet format and procedures for controlling the
projector.
In the following sections below, the term “CONTROLLER” is used as a device which controls the projec-
tor. CONTROLLER can be a PC or other specific device that is able to handle RS-232C.
Although most of commands are available for both RS-232C.
1-2. Glossary of Terms
Table 1-1 Glossary of Terms
Terms Abbreviated Description
CONTROLLER _Command initiator such as PCs.
PROJECTOR _Front projector.
1-3. Protocol Stack Structure
The protocol stack structure diagram is shown below. Though the stack is drawn for RS-232C, the follow-
ing portions are common.
Table 1-2 Common Portions in Protocol Stack
Layer Name Description
Sub Command Value is assigned for projector’s functions. Refer to the section 2-1 for detail
description.
Simplified Command Packet format for sending/receiving “Sub Command”. Refer to the section 3-4-1 for
detail description.
(1) RS-232C
Fig. 1-1 RS-232C Protocol Stack
“RS-232C” layer is physical portion and “Asynchronous” is the traditional protocol layer as shown in the
section 3-2.
2VPL-HW15
2. Common Commands
2-1. Sub Commands
Sub Command is the value which is used by Simplified Command. Value is assigned for executing func-
tion. For example, if you want to change the picture mode, the appropriate value assigned for the desired
picture mode should be chosen.
2-1-1. ITEM List
Item list tables are described below. Tables are shown per function category.
Table 2-1 ITEM List For Picture
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Picture Mode 00h 02h Dynamic 0000h Set/Get
Standard 0001h
Cinema 0002h
User1 0003h
User2 0004h
User3 0005h
Contrast 00h 10h 0000h to 0064h (0 to 100)
Brightness 00h 11h 0000h to 0064h (0 to 100)
Color 00h 12h 0000h to 0064h (0 to 100)
Hue 00h 13h 0000h to 0064h (0 to 100)
Sharpness 00h 14h 0000h to 0064h (0 to 100)
Color Temp. 00h 17h High 0000h
Mid 0001h
Low 0002h
Custom1 0003h
Custom2 0004h
Custom3 0005h
Custom4 0006h
Lamp Control 00h 1Ah Low 0000h
High 0001h
Black Level Adj. 00h 1Ch Off 0000h
Low 0001h
High 0002h
Advanced Iris 00h 1Dh Off 0000h
Manual 0001h
Auto1 0002h
Auto2 0003h
Real Color Processing 00h 1Eh Off 0000h
User1 0001h
User2 0002h
User3 0003h
3
VPL-HW15
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Film Mode 00h 1Fh Off 0000h Set/Get
Auto1 0001h
Auto2 0002h
Gamma Correction 00h 22h Off 0000h
Gamma 1 0001h
Gamma 2 0002h
Gamma 3 0003h
Gamma 4 0004h
Gamma 5 0005h
Gamma 6 0006h
NR 00h 25h Off 0000h
Low 0001h
Middle 0002h
High 0003h
Block NR 00h 26h Off 0000h
Low 0001h
Middle 0002h
High 0003h
Mosquito NR 00h 27h Off 0000h
Low 0001h
Middle 0002h
High 0003h
Color Space 00h 3Bh Normal 0000h
Wide 0001h
USER GAIN RED 00h 50h FFE2h to 001Eh (_30 to 30)
USER GAIN GREEN 00h 51h FFE2h to 001Eh (_30 to 30)
USER GAIN BLUE 00h 52h FFE2h to 001Eh (_30 to 30)
USER BIAS RED 00h 53h FFE2h to 001Eh (_30 to 30)
USER BIAS GREEN 00h 54h FFE2h to 001Eh (_30 to 30)
USER BIAS BLUE 00h 55h FFE2h to 001Eh (_30 to 30)
Iris Sensitivity 00h 56h Recommend 0000h
Fast 0001h
Slow 0002h
Iris Manual 00h 57h 0000h to 0064h (0 to 100)
4VPL-HW15
Table 2-2 ITEM List For Screen
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Wide Mode 00h 20h Full 0000h Set/Get
Normal 0001h
Wide Zoom 0002h
Zoom 0003h
Full1 0007h
Full2 0008h
Over Scan 00h 23h Off 0000h
On 0001h
Screen Area 00h 24h Full 0000h
Through 0001h
Table 2-3 ITEM List For Setup
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Input 00h 01h Video 0000h Set/Get
S Video 0001h
Input A 0002h
Component 0003h
HDMI1 0004h
HDMI2 0005h
Picture Muting 00h 30h Off 0000h
On 0001h
5
VPL-HW15
Table 2-4 ITEM List For Status
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Status Error 01h 01h NO ERROR 0000h Get only
LAMP ERROR 0001h
FAN ERROR 0002h
COVER ERROR 0004h
TEMP ERROR 0008h
D5V ERROR 0010h
POWER ERROR 0020h
TEMP WARNING 0040h
NVM Data ERROR 0080h
Status Power 01h 02h STANBY 0000h
START UP 0001h
STARTUP LAMP 0002h
POWER ON 0003h
COOLING1 0004h
COOLING2 0005h
SAVING COOLING1 0006h
SAVING COOLING2 0007h
SAVING STABY 0008h
Lamp Timer 01h 13h USE TIME 0000h-FFFFh *1
*1 Example) In case the lamp timer indicates 1000H, return values are [03h] upper byte and [E8h] lower byte.
Table 2-5 ITEM List For Infrared Remote Command
<Table 1> <Table 2> Remarks
Item Number Data
Item Upper byte Lower byte Data Upper byte Lower byte
Infrared Remote
Command
(15 bit category)
17h Refer to the
section 2-1-2*1.
00h 00h Set Only
Infrared Remote
Command
(20 bit category)
19h Refer to the
section 2-1-2*1.
(Table 2-6-
Table 2-9)
00h 00h
Infrared Remote
Command
(20 bit category)
1Bh Refer to the
section 2-1-2*1.
(Table 2-10)
00h 00h
*1: By using this Item Number, it is possible to simulate the infrared remote controller.
Choose your desired Code from the table in the section 2-1-2 and use it as the Lower byte of Item Number.
n
Depending on the category, different value (Upper byte) is assigned.
6VPL-HW15
2-1-2. Infrared Remote Command Code
Tables are shown per function category.
.15 bit PROJECTOR: Table 2-6-Table 2-9
.20 bit PROJECTOR-E: Table 2-6-Table 2-9
.20 bit PROJECTOR-EE: Table 2-10
Table 2-6 Infrared Remote Command Code For Picture
CATEGORY Code Name
15 bit
PROJECTOR
20 bit
PROJECTOR-E
O_ 07 BLACK LEVEL
O_ 18 CONTRAST +HIGH
O_ 19 CONTRAST _LOW
O_ 1A COLOR +HIGH
O_ 1B COLOR _LOW
O_ 1E BRIGHTNESS +BRIGHT
O_ 1F BRIGHTNESS _DARK
O_ 20 HUE +GREENISH
O_ 21 HUE _PURPLISH
O_ 22 SHARPNESS +SHARP
O_ 23 SHARPNESS _SOFT
_O 08 RCP
_O 09 ADJUST PICTURE TOGGLE
_O 4B COLOR SPACE TOGGLE
_O 51 PICTURE MODE DYNAMIC
_O 52 PICTURE MODE STANDARD
_O 53 PICTURE MODE CINEMA
_O 54 PICTURE MODE USER1
_O 55 PICTURE MODE USER2
_O 56 PICTURE MODE USER3
_O 5B PICTURE MODE TOGGLE
_O 5C COLOR TEMP TOGGLE
_O 5E GAMMA COLLECTION TOGGLE
_O 5F IRIS MODE TOGGLE
Otros manuales para VPL VPL-HW15
3
Tabla de contenidos
Otros manuales de Proyector de Sony
Sony
Sony BRIGHTERA VPL-FH30 Manual de usuario
Sony
Sony VPL-ES7 Manual de usuario
Sony
Sony VPL-ES3 Manual de servicio
Sony
Sony VPL-PX20 Manual de usuario
Sony
Sony VPL-FHZ700 Manual de usuario
Sony
Sony SuperData VPH-1251Q Manual de usuario
Sony
Sony VPL-VW695ES Manual de servicio
Sony
Sony VPL-CX70 Manual de servicio
Sony
Sony SRX-R210 Guía del usuario
Sony
Sony SRX-T105 Manual de usuario
Sony
Sony VPL VPL-HW15 Manual de usuario
Sony
Sony VPD-MX10 Manual de usuario
Sony
Sony VPL-EW5 Manual de usuario
Sony
Sony VPLSW536 Guía
Sony
Sony VPL-VW870ES Manual de usuario
Sony
Sony VPL-FHZ101L Manual de usuario
Sony
Sony VPL-HS50 Manual de usuario
Sony
Sony HDMI VPL-FE40L Manual de usuario
Sony
Sony PSS-H10 Manual de usuario
Sony
Sony KP 48S70 Manual de usuario
