Sony KD-60X690E Manual de usuario

SERVICE MANUAL

Version Date Subject

1.0 2017/6/27 First version issue.

LCD Digital Color TV

9-888-740-01

HISTORY INFORMATION FOR THE FOLLOWING MANUAL:

ORIGINAL MANUAL ISSUE DATE: 2017/6/27 GN3FK CHASSIS

Segment: KCL

MODEL LIST

MODEL COLOR COMMANDER DEST.MODEL COLOR COMMANDER DEST.

KD-60X690E Black RMT-TX300U UC2/LA1

KD-70X690E Black RMT-TX300U UC2/LA1

KD-60X695E Black RMT-TX300B AR4/LA8

KD-60X697E Black RMT-TX300B CO1

KD-60X6700E Black RMT-TX300E/300P AZ1/ME6/EA4

KD-70X6700E Black RMT-TX300E/300P AZ1/ME6/EA4

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

WARNINGS AND CAUTIONS

CAUTION

These servicing instructions are for use by qualified service personnel only.

To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

WARNING!!

An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.

The chassis of this receiver is directly connected to the ac power line.

CARRYING THE TV

Be sure to follow these guidelines to protect your property and avoid causing serious injury.

• Carry the TV with an adequate number of people; larger size TVs require two or more people.

• Correct hand placement while carrying the TV is very important for safety and to avoid damages.

SAFETY-RELATED COMPONENT WARNING!!

Components identified by shading and ! mark on the schematic diagrams, exploded views, and in the parts list are critical for safe operation. Replace these components with Sony

parts whose part numbers appear as shown in this manual or in supplements published by Sony. Circuit adjustments that are critical for safe operation are identified in this manual.

Follow these procedures whenever critical components are replaced or improper operation is suspected.

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

When repairing the LCD panel, be sure you are grounded by using a wrist band.

When repairing the LCD panel on the wall, the LCD panel must be secured using the 4 mounting holes on the rear cover.

1) Do not press on the panel or frame edge to avoid the risk of electric shock.

2) Do not scratch or press on the panel with any sharp objects.

3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.

4) Do not expose the LCD panel to direct sunlight.

5) Avoid contact with water. It may cause a short circuit within the module.

6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)

7) Always clean the LCD panel with a soft cloth material.

8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.

9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).

10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.

USE CAUTION WHEN HANDLING THE LCD PANEL

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

SAFETY CHECK-OUT

After correcting the original service problem, perform the following safety checks before releasing the set to the customer:

1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.

2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.

3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.

4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.

5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.

6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.

7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.

8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

SAFETY CHECK-OUT

Leakage Test

(To protect electric shock when customer touch the terminal.)

Leakage current can be measured by V: Voltmeter or oscilloscope (r.m.s. or peak reading)

Stabilized power supply instrument and isolated voltage transformer: Use too much current capacity and

isolated voltage transformer does not need to use stabilized power supply equipment Specification of RMS volt

meter: Input resistance > 1 M ohm, Input capacitance < 200 pF, Frequency range: 15 Hz – 1MHz (Refer Figure

A). Isolated type volt -meter (FLUKE 8921A etc *1)

*1 Not use FLUKE 8920A that connected to protective earth by diode

# Leakage current of measurement instrument is less than 10μArms when under test equipment AC plug is

opened # Set up the following condition and turn on the set.

Applied voltage: Nominal input voltage (Description on Nameplate) # Measure the leakage current between

one phase conductor and neutral for terminal A and terminal B.

Read rms value, and then calculate to peak value PEAK VALUE =√2 RMS VALUE

Comply with the following requirement Class II equipment (2-pin plug): for each terminal, the worst value of

measurement must not exceed AC 350uA peak). Note: including AC adaptor, AC adaptor/DC operated unit

combination

How to Find a Good Earth Ground

A cold-water pipe is a guaranteed earth ground; the cover-plate retaining screw on most AC outlet boxes is also

at earth ground.

If the retaining screw is to be used as your earth ground, verify that it is at ground by measuring the resistance

between it and a cold-water pipe with an ohmmeter. The reading should be zero ohms.

If a cold-water pipe is not accessible, connect a 60- to 100-watt trouble- light (not a neon lamp) between the hot

side of the receptacle and the retaining screw. Try both slots, if necessary, to locate the hot side on the line; the

lamp should light at normal brilliance if the screw is at ground potential (see Figure B).

Figure A. Measuring network for Leakage Current

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

SELF DIAGNOSIS FUNCTION

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

Error Items Number of LED

flashing Go to Shutdown

State Description

MAIN_POWER 2Yes Detect and observe main voltage

(1) 19.5V from AC adapter

(2) 12V from power board (TBD)

AUD_ERR 3Yes Detecting/Observing audio AMP error

AUD_I2C 3Yes Audio AMP communication error

TU_DEMOD -No

(Only record error

log)

Tuner & Demodulator I2C communication

monitoring.

Tuner Detect signal monitoring.

PANEL_POWER_ERR 4Yes Detect and observe for Panel_12V

PANEL_I2C_ERR 5

Yes Detect Panel I2C Communication access error

BACKLIGHT 6Yes Detect and observe backlight error

LED_I2C 6Yes LED Driver communication error

BE_I2C -No

(Only record error

log) BE device I2C communication error detection.

PMIC_I2C -No

(Only record error

log) PMIC communication error

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

SELF DIAGNOSIS FUNCTION

[SELF DIAGNOSTIC SCREEN DISPLAY]

Error count

Item name

STBY LED flash time

Total operation time by hour

Boot count

Panel operation time by hour

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.

After you have completed the repairs, clear the result display to “0”.

Clearing the Self Check Diagnostic List

1. Error history and Error count : Press the Channel 8 => Channel 0 .

2. Panel operation time : Press the Channel 7 => Channel 0 .

Exiting the Self-diagnostic screen

To exit the Self Diagnostic screen, turn off the power to the TV by pressing the POWER button on the remote or the POWER button on the TV.

• Items with no part number and no description are not stocked because they are seldom required for roution service.

• The construction parts of an assembled part are indicated with a collation number in the remark colum.

• Items marked " * " are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.

SEC 1. DISASSEMBLY AND PARTS LIST

KD-60X690E/KD-70X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E/KD-70X6700E(AZ1/ME6/EA4)

DISASSEMBLY AND PARTS LIST

1-2. KD-60X690E/KD-60X695E/KD-60X697E/KD-60X6700E

KD-60X690E(UC2/LA1)/KD-60X695E(AR4/LA8)/KD-60X697E(CO1)/KD-60X6700E(AZ1/ME6/EA4)

-723-296-01 SCREW, +PSW M5X12

-682-961-09 SCREW, +PSW M4x8 W8

-729-979-01 SCREW,F,CROSS,T.T-3*6,BLK-ZN.

1-2-1. STAND BLOCK

1-2-2. STAND COVER ASSY AND STAND BASE ASSY AND NECK

REF.NO. PART No.

DESCRIPTION

MARK

1 4-723-281-01

STAND, NECK

2 4-723-280-01

STAND, COVER

3 4-723-282-01

STAND, BRACKET L

4 4-723-283-01

STAND, BRACKET R

5 4-723-284-01

STAND, BRACKET FRONT

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Televisor LCD de Sony

Sony

Sony FDL-370 Manual de usuario

Sony

Sony KDL-32W700B Manual de usuario

Sony

Sony BRAVIA KD43X75WL Manual del propietario

Sony

Sony Bravia XBR-65X905A Manual de usuario

Sony

Sony KDL-32L504 - 32" Class Bravia L Series Lcd... Manual de usuario

Sony

Sony KDL-40V3000, KDL-46V3000 Manual de usuario

Sony

Sony Bravia KDL-40BX450 Manual de usuario

Sony

Sony KDL-40SL140 - 40" Bravia Sl Series Lcd Tv Manual de usuario

Sony

Sony BRAVIA KDL-26M4000 Manual de usuario

Sony

Sony KDL-40S2010 - 40" Bravia Lcd Hdtv Manual de usuario

Sony

Sony WEGA KLV 23M1 Manual de usuario

Sony

Sony WEGA KLV-17HR2 Manual de usuario

Sony

Sony BRAVIA KLV-26S200 Manual de usuario

Sony

Sony KDL-V26XBR1 Operating Instructions... Manual de usuario

Sony

Sony Bravia KDL-40S504 Manual de usuario

Sony

Sony KDL40W5500U Manual de usuario

Sony

Sony FW-32BU30J Manual de usuario

Sony

Sony Bravia KLV-26U300A Manual de usuario

Sony

Sony BRAVIA KDL-32EX720 Manual de usuario

Sony

Sony KD-55X85L Instrucciones de operación

Sony

Sony Bravia KD-65X7007F Manual de usuario

Sony

Sony BRAVIA KDL-S23A11E Manual de usuario

Sony

Sony WEGA KLV 21SG2 Manual de usuario

Sony

Sony Bravia KDL--48W705C Manual de usuario

Manuales populares de Televisor LCD de otras marcas

LG 32LC4R* Manual de usuario

ViewSonic

ViewSonic N4200w-1 VS10945-1M Manual de usuario

Salora

Salora 22LED1600 Manual de usuario

Samsung

Samsung LA32E420 Guía

Dell

Dell W1900 19 Instrucciones de uso

Samsung

Samsung LN40C670M1F Manual de usuario

Samsung

Samsung Series 4+ Manual de usuario

Samsung

Samsung 5 Series Manual de usuario

Grundig

Grundig 40 VLE 8230 BP Manual de usuario

Philips

Philips 43PFL4901/F7 Manual de usuario

LG 32LS350 Manual de usuario

VIORE

VIORE LED32VF60 Manual de usuario

Toshiba

Toshiba Regza 42HL167 Manual de usuario

JVC

JVC LT-32A220 Manual de usuario

Philips

Philips 20TA1000/93 Manual de usuario

Philips

Philips 32PFL3158T/12 Manual de usuario

Vizio

Vizio VP422HDTV10A - 42" Plasma TV Manual de usuario

Philips

Philips 40PFL7705D Manual de usuario