Sony SVR-3000 - Digital Network Recorder Guía de inicio rápido
WeaKnees.com
http://www.weaknees.com/
TIVO UPGRADE INSTRUCTIONS
(c) 2001-2003, Adberg Consulting LLC. All rights reserved.
Instructions for replace drive upgrade for Sony SVR-3000
A FEW WORDS OF CAUTION:
First and foremost, please be aware that upgrading a TiVo presents a few physical hazards. As
with most consumer electronics devices, components in the TiVo may still carry a lethal charge,
even after disconnecting from your power supply. Be aware of this while working inside your TiVo.
Allow sufficient time for discharging of components and avoid contact as much as possible with
potential hazards. While we have done everything we can to provide accurate, easy-to-follow
instructions, we cannot be responsible for any damage done to your TiVo or to yourself as a result
of your upgrade. By opening your TiVo, you agree that neither Adberg Consulting LLC nor any of its
members or affiliates is responsible in any way for any harm done. Please be VERY careful when
upgrading. NEVER open the TiVo while the unit is plugged in and NEVER operate the TiVo if the lid
is not securely fastened.
Please Note: Opening the TiVo voids the warranty.
1. OPENING THE TIVO
1.1. Unplug the power cord from the TiVo and wait five minutes for the TiVo to
discharge. Do not plug the TiVo back in until you are completely finished. Be very careful
of static electricity, which can destroy your TiVo’s internal parts. You shouldn’t perform
this upgrade on carpet.
1.2. Using a Philips-head screwdriver, unscrew the four screws on the back of
your TiVo. The four screws are surrounded by silver from the top of the TiVo’s.
1.3. Next, remove the four, large-head screws, two on each side of the unit.
1.4. Once the eight screws are removed, you have to remove the lid, which can
sometimes be difficult. The WeaKnees.com “tried and true” method is to place the TiVo on
the floor and kneel down with your knees about 6 inches from the FRONT of the TiVo.
Place your palms on the top side edges of the TiVo, toward the back and push toward the
back of the TiVo (this occasionally requires a bit of force). The cover should slide back and
then up. Remove the cover from the TiVo, and set it in front of the TiVo unit, top up. You
will use this as a platform for the drive bay.
WeaKnees.com
http://www.weaknees.com/
2. DISCONNECTING THE DRIVE BAY
2.1. With the cover off and looking underneath the front lip of the TiVo, you will
be able to see (1) one hard drive, (2) a ribbon cable that runs from the greenish
motherboard underneath the drive to the hard drive, (3) a multi-colored (red, black,
yellow) power cable that runs from the power supply to the hard drive, and (4) a fan cable
that runs from the hard drive bay to the motherboard.
2.2. Place the TiVo lid upright in front of the TiVo, forming a platform that will be
used to support the drive bay after you remove it.
2.3. Gently remove the fan cable from the motherboard. Pull straight up and out.
(See Picture.)
WeaKnees.com
http://www.weaknees.com/
2.4. Using your screwdriver, unscrew and remove the four screws securing the
drive bay to the TiVo chassis.
2.5. Once the screws are removed, you will be able to lift the drive bay up and
out of the TiVo. Flip the drive bay up and out of the TiVo and onto the TiVo lid, with the
hard drive face-down on the TiVo lid and the two cables running from the drive to the
TiVo. You will now need to remove both of the cables connected to the hard drive by
following the instructions below:
(a)The hard drive has a power connector running into the hard drive. The
power cable has a white connector plugged into the hard drive. Remove the power
connector from the hard drive. The power cables are sometimes difficult to remove;
patience and wiggling it back and forth usually does the trick.
(b)Remove the hard drive ribbon cable (longer, gray cable with a blue or
black connector) from the hard drive by pulling on the hard plastic piece connected to the
hard drive.
3. REMOVING THE EXISTING DRIVE(S)
3.1. With the hard drive bay upside down on the TiVo lid, remove the four screws
connecting the hard drive to the hard drive bay. Do not confuse these screws with the
four screws you removed from the back of the TiVo before removing the lid.
3.2. Set aside the drive(s) you have just removed for safe keeping.
4. CONNECTING THE NEW HARD DRIVE TO THE DRIVE BAY
4.1. Included in your upgrade kit is a replacement hard drive. You will need the
four screws that you removed from the hard drive bay. The screws will be used to attach
the upgrade drive to the drive bay.
4.2. Install the drive in the same position as the drive you just removed.
WeaKnees.com
http://www.weaknees.com/
5. CONNECTING THE POWER AND HARD DRIVE CABLES TO THE DRIVE
5.1. If you have the floor/table space, move to the back of your TiVo so that you
are looking at the back of the two hard drives.
5.2. Connect the power cord to the new drive, being sure to align the power
connectors properly (rounded side down). Be sure that the power connector is securely
fastened.
5.3. Connect the hard drive cable to the hard drive. Again, be sure the cable is
pushed snugly into the drive (it only fits one way). Be very careful not to bend any of the
hard drive pins.
5.4. Now move back in front of your TiVo to re-attach the drive bay.
6. RE-ATTACHING THE DRIVE BAY
6.1. Once you have the cables connected to the drive, carefully flip the drive bay
over.
WeaKnees.com
http://www.weaknees.com/
6.2. Align the four screw holes in the bracket with the holes on the TiVo chassis.
Make sure the cables aren’t under the bracket and that the bracket sits flat on the chassis
mount. Make sure the fan cable is free.
6.3. Screw the four screws back into the holes on the drive bay.
6.4. Insert the fan cable back into the motherboard. (This is easy to
forget, which is why it is in bold!)
7. RE-ATTACHING THE TIVO LID
7.1. Kneel down in front of your TiVo as you did when you removed the lid. Place
the TiVo lid back over the TiVo. Align the clips on each side of the lid so that they clip
down on the sides of your TiVo. Slide the lid toward you while simultaneously pushing
down on the top of the lid.
7.2. Once the lid is in place, reattach the eight screws.
We thank you very much for your purchase and hope that you enjoy your newly-enhanced
TiVo. Please email us with any comments, suggestions or complaints. If you found the
upgrade easy to install (or even if you found it more difficult than you expected), we’d
love to know. If you found our service to be excellent (or awful), we want to know that
too. We’re always looking to improve our products and services…the more we hear from
you, the better. Thanks very much!
Otros manuales para SVR-3000 - Digital Network Recorder
8
Tabla de contenidos
Otros manuales de DVR de Sony
Sony
Sony VR-510U Manual de usuario
Sony
Sony BKMA-U70XGI Manual de usuario
Sony
Sony DHG-HDD250 - 30-Hour High-Definition Digital Video... Manual de usuario
Sony
Sony MAV-555SS Manual de usuario
Sony
Sony DSR-1800AP Manual de usuario
Sony
Sony GV-300R - Video Walkman Manual de usuario
Sony
Sony PWS-4400 Manual de usuario
Sony
Sony Handycam HDRSR11 Manual de usuario
Sony
Sony SVR-3000 - Digital Network Recorder Guía de inicio rápido
Sony
Sony SVR-3000 - Digital Network Recorder Manual de uso y mantenimiento
Sony
Sony Vaio PCG-GRT240G Instrucciones de uso
Sony
Sony DNW-A100 Manual de usuario
Sony
Sony SVR-3000 - Digital Network Recorder Manual de usuario
Sony
Sony Ipela NSR-S10 Manual de usuario
Sony
Sony HVO-3300MT Manual de usuario
Sony
Sony DSR-2000A Manual de usuario
Sony
Sony Handycam HDR-CX240 Manual de usuario
Sony
Sony DCR-TRV19 Manual de instrucciones / Manual de... Manual de usuario
Sony
Sony DHG-HDD250 - 30-Hour High-Definition Digital Video... Manual de usuario
Sony
Sony Giga Pocket Manual de usuario
