SonicWALL SSL-IA Instrucciones de instalación
SonicWALL SSL-IA/SSL-R
Hardware Guide
Page 2 SonicWALL SSL-IA/SSL-R Hardware Guide
CONTENTS
ABOUT THIS GUIDE ....................................................... 2
PACKAGE CONTENTS................................................... 2
INSTALLING THE HARDWARE ......................................... 3
Locating the SSL-IA ......................................................... 3
Locating the SSL-R .......................................................... 3
Connecting the SSL Appliance to Ethernet ......................... 3
ABOUT THIS GUIDE
This guide will help you install the SSL-IA and SSL-R hardware, collec-
tively known as SonicWALL SSL appliances. See the
SSL-IA/SSL-R User
Guide
for instructions on Secure Sockets Layer (SSL) configurations.
PACKAGE CONTENTS
The following items are shipped in the SSL-IA packaging:
• One SonicWALL SSL-IA appliance
• Serial access cable
• Power supply and cable
• One SonicWALL CD-ROM
• This Hardware Guide
• One SonicWALL User Guide (on CD only)
• Registration Card
The following items are shipped in the SSL-R packaging:
• One SonicWALL SSL-R appliance
• Two power cables
• Four rack mounting screws and washers
• One SonicWALL
CD-ROM
• This Hardware Guide
• One SonicWALL User Guide (on CD only)
• Registration Card
Page 3
The root directory of the CD-ROM includes a readme.txt file that
contains information for the different software components and other
information that became available after this guide
went to press.
The subdirectory entitled Docs contains .pdf versions of the product
documentation. Release notes for each operating system are lo-
cated in that operating system’s directory in a file called release.txt.
If you find that any item is missing, contact SonicWALL, Inc. imme-
diately via the Web <http://www.sonicwall.com/support/> or
phone (408) 745-9600.
INSTALLING THE HARDWARE
Locating the SSL-IA
Place the SSL-IA on a level surface in an area with access to your
network cabling and close enough to the configuring computer to
allow serial access. Allow at least an inch of space around the
SSL-IA for adequate ventilation.
Locating the SSL-R
If you are placing the SSL-R in a standard rack, use the included screws
to attach the appliance securely. If you are placing the SSL-R on a shelf,
you may remove the rack-mounting “ears”. Allow at least an inch of
space around the SSL-R sides for adequate ventilation.
Connecting the SSL Appliance to Ethernet
1. Use Category 5 UTP cables with RJ-45 connectors. SonicWALL
SSL appliance Ethernet interfaces are configured as NIC ports.
— Use a
straight-through
cable to connect the SSL appli-
ance to a hub or switch.
— Use a
crossover
cable to connect the SSL appliance to a
NIC.
2. The connection to the Internet must use the “Network” port;
the connection to the server(s) must use the “Server” port.
Push the connector into the jack until it clicks into place.
3. Check the Link LEDs on the equipment. The green Link (LK)
LED should be solidly lit on the networking equipment. The
green Receive (RX) and amber Transmit (TX) LEDs on the SSL
appliance will flash as packets travel to and from the SSL
appliance. If the Link LED does not light, see the Appendix
B - Troubleshooting in the User Guide for suggestions.
Page 4 SonicWALL SSL-IA/SSL-R Hardware Guide
Part # 232-000116-00 Rev. A
12/00
SonicWALL, Inc.
1160 Bordeaux Drive
Sunnyvale, CA 94089-1209
Tel: 408-745-9600
Fax: 408-745-9300
E-mail: [email protected]
Web: http://www.sonicwall.com
©2000 SonicWALL, Inc. All rights reserved.
Under the copyright laws, this manual or the software described
within, may not be copied, in whole or in part, without the written
consent of the manufacturer, expect in the normal use of the soft-
ware to make a backup copy. The same proprietary and copyright
notices must be affixed to any permitted copies as were affixed to
the original. This exception does not allow copies to be made for
others, whether or not sold, but all of the material purchased (with
all backup copies) may be sold, given, or loaned to another per-
son. Under the law, copying includes translating into another
language or format.
This product includes cryptographic software written by Eric A.
Young. This product includes software written by Tim J. Hudson.
SonicWALL is a registered trademark. All trademarks and trade
names belong to their respective holders.
Specifications in this manual are subject to change without notice.
4. To disconnect a cable, press the small tab on the connector
and gently pull the connector from the jack. If the connector
does not disengage, press the tab down more firmly and pull
again.
Note: You must connect the cables to the SSL appliance so client
requests (inbound) and server traffic (outbound) move through dif-
ferent ports. Inbound traffic uses the “Network” port. Outbound
traffic uses the “Server” port. The configuration computer must be
connected via the “Server” port. This is discussed further in the
SSL-IA/SSL-R User Guide
.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cortafuegos de SonicWALL
SonicWALL
SonicWALL NSA 2650 Manual de usuario
SonicWALL
SonicWALL TZ570 Manual de usuario
SonicWALL
SonicWALL NSA 2400 Manual de usuario
SonicWALL
SonicWALL NSA E7500 Manual de usuario
SonicWALL
SonicWALL NSA 250M series Manual de usuario
SonicWALL
SonicWALL CSa 1000 Manual de usuario
SonicWALL
SonicWALL Email Security 6000 Manual de usuario
SonicWALL
SonicWALL SuperMassive 9800 AC Manual de usuario
SonicWALL
SonicWALL ESA 4300 Manual de usuario
SonicWALL
SonicWALL TZ 190 Manual de usuario
SonicWALL
SonicWALL TZ 100 Series Manual de usuario
SonicWALL
SonicWALL TZ 170 SP Manual de usuario
SonicWALL
SonicWALL TZ670 Manual de usuario
SonicWALL
SonicWALL TZ 170 SP Manual de usuario
SonicWALL
SonicWALL TZ600 Manual de usuario
SonicWALL
SonicWALL TZ 170 Manual de usuario
SonicWALL
SonicWALL SuperMassive 9200 Manual de usuario
SonicWALL
SonicWALL TZ 180 Manual de usuario
SonicWALL
SonicWALL TZ 180 Manual de usuario
SonicWALL
SonicWALL TZ 150 Wireless Manual de usuario
