Sona SonaSky Instrucciones de montaje
SonaSky
Motorised Skylight Blind
1
SonaSky Motorised Blind FITTING GUIDE
SONASHADES.COM
This product and all its components must be tted by a qualied professional.
Ensure the electrical power is turned off before tting this product.
The power supply intended for this product is 12v.
Ensure the product is securely fastened before releasing.
Do not install this product externally, in wet or high moisture environments.
Do not install this product with small children or pets around.
This product is not intended for use by children.
Keep the handset out of reach of children.
Never drop, knock, puncture or immerse the handset in liquids of any type.
SAFETY
INSTRUCTIONS
1
2
3
4
5
6
7
8
9
FITTING GUIDE
SONASHADES.COM 2
SonaSky Motorised Blind
STEP 1
1.1
1.2
1.3
Unpack all the contents out of the box and lay them carefully on a at surface.
Your box should contain:
• 1 x Motorised Blind
• A1
• A3
• B1
• B2
• 1 x Handset (Optional)
• 1 x Power Supply (Battery / Solar or Mains) (Optional)
Identify the rails marked ‘A1’ and ‘A3’. These rails are to be tted rst starting with
rail ‘A1’ then moving on to rail ‘A3’.
Rail ‘A1’ is classed as the motor rail, to which the motor side below ts to (the
motor side is where the fabric is stacked / motor is located). Decide which side
of the opening you would like the motor side to be positioned on and t rail ‘A1’
accordingly.
FITTING GUIDE
SONASHADES.COM 3
SonaSky Motorised Blind
1.4
1.5
1.6
1.7
Motor Side
If you have a perimeter trim already installed measure 10mm down from the bottom
of this trim and position rail ‘A1’. Make sure rail ‘A1’ is LEVEL and mark your drill
positions with a pen through the pre-drilled holes already visible on the rail.
Take away the trim and drill your holes required through the plasterboard ensuring
you DO NOT drill into the timber behind it.
Using the screws provided, screw the trim on securely. DO NOT over tighten the
screws as this may damage the plasterboard.
Repeat the above steps 1.4, 1.5 and 1.6 for rail ‘A3’.
A1
10mm
FITTING GUIDE
SONASHADES.COM 4
SonaSky Motorised Blind
STEP 2
2.1
2.3
2.2
2.5
2.4
Now locate the remaining side rails marked ‘B1’ and ‘B2’.
Rest rails ‘B1’ and ‘B2’ on the already tted rails ‘A1’ and ‘A3’ (see image below).
Secure the rail ‘B1’ rst. Depending on the length of rail ‘B1’ it should t nicely in-
between rails ‘A1’ and ‘A3’.
Secure rail ‘B1’ by rstly marking the drill positions with a pen through the pre-drilled
holes already visible on the rail. Take away the trim and drill your required holes
through the plasterboard ensuring you DO NOT drill into the timber behind it.
Using the screws provided, start at the middle of rail ‘B1’ and screw the trim on
securely so all ends are securely xed. DO NOT over tighten the screws as this may
damage the plasterboard.
B1 or B2 A1 or A3
FITTING GUIDE
SONASHADES.COM 5
SonaSky Motorised Blind
STEP 3
CLEANING CHECK – Once all the rails are now securely xed into place, before
tting the Blind it is important to clean any debris from the top of the rails so the
Blind can run smoothly. Not cleaning the rails may cause an obstruction which
could potentially cause damage to the Blind.
Clean Top of Rail
Clean Top of Rail
End Prole
Motor Side
3.1 Unwrap the Blind carefully and lay it out on a clean at surface. (See image below).
FITTING GUIDE
SONASHADES.COM 6
SonaSky Motorised Blind
ORIENTATION CHECK – On the motor side of the Blind, please ensure the metal
nylon tensioners are facing upwards towards the ceiling so the Blind is facing the
correct orientation (see image of a nylon tensioner below). The tensioners should
not be visible from ground level once the Blind is tted.
3.2 Fit the motor side of the Blind rst to rail ‘A1’.
Start at one end and clip the motor side of the
Blind into rail ‘A1’ as per the diagram and image
below. We recommend resting the Blind on the
side rails ‘B1’ and ‘B2’ whilst doing so. Begin
clipping at one end and make your safely way
across. Moderate force is required.
FITTING GUIDE
SONASHADES.COM 7
SonaSky Motorised Blind
3.3
3.4
Now move your ladders safely across to the opposite side of the lantern so you are facing
rail ‘A3’. Leave enough space so you are at arm’s length to clip in the end prole in.
Rest the prole on the side rails ‘B1’ and ‘B2’. The side requires considerable force to clip
in the end prole to the rail ‘A3’ brackets securely. It will seem short on length (80mm)
but this is normal. Start in the middle of the rail and work your way outwards to each end
making sure each time it clips into the bracket securely (see image below).
FITTING GUIDE
SONASHADES.COM 8
SonaSky Motorised Blind
FITTING CHECK – force the end prole into rail ‘A3’ brackets and push hard to click
into place. Work from the middle outwards, it will make a loud positive ‘clicking
noise’ as it secures into place.
3.5
3.6
3.7
The Blind will now be under the correct tension. Get a qualied electrician to
connect the power to the Blind. Once the power is active the Blind will jog once
(back and forth motion) and is now ready to be operated from the handset.
Calibrate the Blind by pressing the down arrow on the handset to fully close, then
the up arrow to full open. The ‘my’ button stops the Blind. This may need to be
done several times to calibrate.
The Blind is now ready for normal operation.
FITTING GUIDE
SONASHADES.COM 9
SonaSky Motorised Blind
STEP 4
WARNING – The battery pack must be mounted under the blind. This avoids
any excessive heat from direct sunlight interfering with the battery’s safety and
performance. Please see manufacturer’s instruction provided for further guidance
(see image below).
Fitting the optional Solar & Battery Pack.
4.1
4.2
4.3
4.4
4.5
Before installing the battery pack, use the black rubber gromets provided and place
into to the pre-drilled hole in the centre of the L-prole rail (see image below).
Thread the motor wire through the hole from the top of the blind.
Now connect the battery pack to the
Blind. Once connected the Blind will
jog once (back and forth motion)
and is now ready to be operated
from the handset.
Calibrate the Blind by pressing the
down arrow on the handset to fully
close, then the up arrow to full open.
The ‘my’ button stops the Blind. This
may need to be done several times
to calibrate.
The Blind is now ready for normal
operation.
OPTIONAL SOLAR PANEL – If using a
solar panel, pass the cable through the
top of the black grommet as the battery
will need to connect to the solar panel
directly. Join the solar panel connector
to the battery pack. The solar panel can
be tted to the glass with sticky pads or
left to rest on the Blind stack if secure
enough (as per the below image).
Battery Pack
Black rubber grommet
to be placed in hole here
FITTING GUIDE
SONASHADES.COM 10
SonaSky Motorised Blind
Tabla de contenidos
Otros manuales de Persiana de ventana de Sona
Manuales populares de Persiana de ventana de otras marcas
Domondo
Domondo PureNight Manual de instrucciones de instalación
rollease acmeda
rollease acmeda Easy Spring Air Guía de configuración
IKEA
IKEA KADRILJ Manual de usuario
Hallis Hudson
Hallis Hudson Rolls Super glide Manual de usuario
Benthin
Benthin P1614 Manual de usuario
MV LINE
MV LINE CLARA 015 Manual de instrucciones
