SOMFY Connect UAI Plus Guía de configuración rápida

INTEGRATION GUIDE

LUTRON® INTEGRATION

via SOMFY CONNECT™ UAI PLUS

TABLE OF CONTENTS

VERSION 1.0 | OCTOBER 2020 | Prepared by PROJECT SERVICES

I. OVERVIEW --------------------------------------------------------- 3

DESCRIPTION

SYSTEM REQUIREMENTS

CONNECTIONS & LEDs

LUTRON COMPATIBILITY

II. INSTALLATION ------------------------------------------------------ 4

MOUNTING & POWER

WIRING TO SYSTEM FOR OPERATION

III. LUTRON SYSTEM SETTINGS ------------------------------------------- 5

NETWORK SETTINGS

TELNET SETTINGS

INTEGRATION SETTINGS

IV. UAI PLUS SYSTEM SETTINGS ------------------------------------------- 8

CONNECTING TO UAI PLUS INTERFACE

NETWORK & INTEGRATION SETTINGS

SDN INTEGRATION REPORT

V. INTEGRATION CONFIGURATION -------------------------------------- 11

LUTRON DEVICES

ADDING LUTRON DEVICES

COMMAND MAPPING LUTRON DEVICES

TESTING & VALIDATION

BUTTON PROGRAMMING EXAMPLES

LUTRON® INTEGRATION via UAI PLUS

INTEGRATION GUIDE

2of 16

PC running Windows 10 or higher

Chrome 59.0.3071 or higher

Latest Somfy Connect UAI Plus Firmware

NOTE: A PC running Windows 10 or higher with Chrome 59.0.3071 or higher is required for motor commissioning

and Somfy Connect UAI Plus firmware updates. A mobile device can be used to control motors once commissioning is complete.

The Somfy Connect™ UAI Plus is designed to commission and control residential and commercial

Somfy Digital Network™ (SDN) motors through IP and RS-232 serial communication.

Integration for the Somfy Connect UAI Plus enables third-party control from Lutron® systems

including HomeWorks® QS, RadioRA 2, RA2 Select, GRAFIK Eye® QS, Quantum® and myRoom Plus.

Platform Compatibility Lutron System Requirements

GRAFIK Eye QS Yes QSE-CI-NWK-E

Caseta No -

RA2 Select Yes RR-SEL-REP2-BL

RadioRA 2Yes RR-MAIN-REP

HomeWorks QS Yes HQP6-1or 2

Quantum Yes QSE-CI-NWK-E

myRoom Prime No -

myRoom Plus Yes GCU-HOSP

Vive No -

I. OVERVIEW

SYSTEM REQUIREMENTS

CONNECTIONS & LEDs

LUTRON COMPATABILITY CHART

(Ethernet)

Port 1

(3rd Party Serial

Connections)

Reset

(Under Removable Cap)

Port 2

(SDN bus)

LED BEHAVIOR:

FAST BLINK

START UP

SLOW BLINK

ONLINE

GREEN

DHCP ACTIVE

AMBER

STATIC IP ACTIVE

3of 16

The Somfy Connect UAI Plus is mounted on a DIN rail either near an automation system,

network switch, or anywhere close to the beginning of an SDN network.

Power is received through the SDN bus via a Bus Power Supply

II. INSTALLATION

MOUNTING & POWER

WIRING TO SYSTEM FOR OPERATION

IP Integration

a. Connect Ethernet Port to the building IP network to which the 3rd Party System is also connected

b. Connect Port 2 to any SDN Device Port

4of 16

RADIO RA2:

HOMEWORKS QS:

The Lutron Integrator must disable DHCP and provide an assigned

IP Address, entered in the UAI Plus Ethernet Settings

NOTE: A Static IP Address is required to maintain Telnet connection

III. LUTRON SYSTEM SETTINGS

LUTRON NETWORK SETTINGS

RA2 SELECT:

GRAFIK EYE QS, QUANTUM & MYROOM PLUS:

*Network Settings will need to be configured upon initial setup and provided by the Lutron Integrator

5of 16

HOMEWORKS QS:

The Lutron Integrator must create a dedicated Telnet Username

and Passphrase, entered in the UAI Plus Telnet Settings

NOTE: Telnet channels cannot be shared. If running the Lutron Home Control + app and the Somfy Connect UAI Plus

application, it is necessary to establish two separate Telnet channels for these two operations to occur.

LUTRON TELNET SETTINGS

RA2 SELECT:

GRAFIK EYE QS, QUANTUM & MYROOM PLUS:

*Telnet Settings will need to be configured upon initial setup and provided by the Lutron Integrator

RADIO RA2:

NOTE: RA2 Select is limited to only one Telnet connection

6of 16

LUTRON INTEGRATION SETTINGS

HOMEWORKS QS:

RADIO RA2:

For the Somfy Connect UAI Plus to see Lutron devices they must be enabled for integration.

All required devices should be confirmed enabled by the Lutron Integrator.

GRAFIK EYE QS, QUANTUM, MYROOM PLUS:

*Integration Settings will need to be configured upon initial setup and provided by the Lutron Integrator

RA2 SELECT:

*RA2 Select integration can only be enabled for the entire system and not individual devices

7of 16

IV. UAI PLUS SYSTEM SETTINGS

CONNECTING TO UAI PLUS INTERFACE

1. Disable the WiFi on the computer, unless connecting to the UAI Plus over a WiFi network

2. Connect Windows PC to the Ethernet Port on the UAI Plus

3. Open the File Explorer then double-click the Network folder

Note: If prompted that network discovery is turned off, click “OK”. Right-click on the

top bar then choose “Turn on network discovery and file sharing”. In the following window,

double-click “No, make the network that I am connected to a private network”.

4. The UAI Plus icon will appear in the list of devices, which means it is now connected. Double-click the UAI Plus

icon in the device list to open a web browser connecting to the UAI Plus homepage

8of 16

NETWORK & INTEGRATION SETTINGS

From the Somfy Connect UAI Plus homepage, hover over the three bars on the top right then click “Settings”:

UDP:

1. Confirm SERVER is set to ENABLE

2. Set LISTEN_PORT to 23

3. Click Restart to enable new settings

Open the UAI Plus tab to enter the UAI Plus Settings & Properties page:

TELNET SETTINGS:

1. Select the Lutron System from SYSTEM dropdown

2. Enter Lutron IP Address in the ADAPTOR_IP field

3. Select ENABLE from the CONNECTION dropdown

4. Enter Telnet Login Username in the LOGIN field

5. Enter Telnet Login Passphrase in the PASSWORD

field –within a few moments the login will take place

Open the Lutron tab to enter the Lutron Settings & Properties page:

NOTE: Prior to integration, confirm the UAI Plus and SDN System are fully configured and functional.

NOTE: A Telnet Username and Password

is not required for RA2 Select

9of 16

SDN INTEGRATION REPORT

To generate the SDN Integration Report, hover over the SDN tab then click “Report”. The

Integration Report is downloaded as a .csv file and viewed in Excel.

10 of 16

The Integration Report lists the available group addresses required for Lutron integration. The

Group Name is selected when command mapping Lutron devices.

Otros manuales para Connect UAI Plus

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Electricidad industrial de otras marcas

Rexroth Indramat

Rexroth Indramat DURADRIVE SYSTEM200 Manual técnico

Abtech

Abtech HVJB Series Guía

Murata

Murata GRM0335C1H8R1DA01 Series Manual de usuario

SAF-HOLLAND

SAF-HOLLAND CBX 5415.5 Manual de usuario

Eaton

Eaton Ulusoy HMH24-04 Manual de usuario

Newlong

Newlong NP-7H Manual de usuario

Murata

Murata GJM0335C1E4R4BB01 Series Manual de usuario

Stahl

Stahl 8575/12 Manual de usuario

SI Pegasus Manual de usuario

Murata

Murata GRM1555C1H2R7CA01 Seies Manual de usuario

Murata

Murata GRM0225C1E6R4BA03 Series Manual de usuario

Cooper Power Systems

Cooper Power Systems VXE15 Manual de usuario

S&C

S&C Vista SD Manual de usuario

Murata

Murata GRM0335C2A7R3CA01 Series Manual de usuario

Siemens

Siemens 3VA9988-0BM10 Manual de usuario

Siemens

Siemens SITRANS LVS100 Manual de usuario

Murata

Murata GRM32ER60G227ME05 Series Manual de usuario

Siemens

Siemens SENTRON SUPERSWITCH 3KL82 Series Manual de usuario