SOMFY Sunea 40 Solar io Manual de usuario

Sunea 40 Solar io

EN Instructions

SL Navodila

Sunea 40 Solar io EN

ORIGINAL INSTRUCTIONS

These instructions apply to all Sunea 40 Solar io drives, the different versions of which are available in the current catalogue.

CONTENTS

Prior information..........................................................................................................................................................

1.1.

Field of application..........................................................................................................................................

1.2.

Liability .............................................................................................................................................................

Installation.....................................................................................................................................................................

2.1.

Assembly ..........................................................................................................................................................

2.2.

Wiring ...............................................................................................................................................................

2.3.

Commissioning ................................................................................................................................................

2.4.

Tips and advice on installation.......................................................................................................................

Use and maintenance ...................................................................................................................................................

3.1.

Up and Down buttons.....................................................................................................................................

3.2.

Stop function ...................................................................................................................................................

3.3.

Favourite position (my) ..................................................................................................................................

3.4.

Operation with sensors ..................................................................................................................................

3.5.

Tips and advice on operation.........................................................................................................................

Technical data ...............................................................................................................................................................

GENERAL INFORMATION

Safety instructions

DANGER

Indicates a danger which may result in immediate death or serious injury.

WARNING

Indicates a danger which may result in death or serious injury.

PRECAUTION

Indicates a danger which may result in minor or moderate injury.

CAUTION

Indicates a danger which may result in damage to or destruction of the product.

EN Sunea 40 Solar io

1.PRIOR INFORMATION

1.1.Field of application

The Sunea 40 drives are designed to drive all types of external vertical screens (without locks), valances and lateral arms

awnings.

The Sunea 40 drives are designed to motorise all types of:

▪

Outdoor awning with or without cassette. All shearing zones shall be protected or inaccessible e.g. at a height ≥

2.50m from the ground or any other access level. There is no shearing risk with the front rail when e.g. the front rail

moves solely by gravity with a mass of less than 15kg or it is pushed with force less than 150N.

▪

External vertical screen which front rail moves solely by gravity with a mass less than 15kg.

Do not use for a lateral arms awning which has a torque peak during its upward movement.

1.2.Liability

Before installing and using the drive, please read these instructions carefully.

In addition to the instructions provided in this guide, please also comply with the instructions provided in the attached Safety

instructions document.

The drive must be installed by a home motorisation and automation professional, in accordance with Somfy’s

instructions and the applicable regulations in the country of installation.

Any operation of the drive outside the field of application described above is prohibited. Such use, and any failure to comply

with the instructions given in this guide and in the attached Safety instructions document, absolves Somfy of any liability and

invalidates the warranty.

After installing the drive, the installer must inform his customers of the operating and maintenance conditions for the drive

and must provide them with the operating and maintenance instructions, and the attached Safety instructions document.

Any After-Sales Service operation on the drive must be performed by a home motorisation and automation professional.

Never begin installing without first checking the compatibility of this product with the associated equipment and

accessories. If in doubt when installing this product and/or to obtain additional information, contact a Somfy representative

or visit the website www.somfy.com.

2.INSTALLATION

WARNING

•

These instructions are mandatory for the home motorisation and automation professional installing the drive.

•

Comply with current standards and legislation in the country of installation.

CAUTION

•

Never drop, knock or puncture the drive or immerse it in liquid.

•

Install an individual control point for each drive.

•

The Sunea 40 Solar io drive must be installed with a 3.2 W Solar Panel solar panel and with either Oximo WireFree

Battery, Oximo WireFree Battery Stick, or Somfy 12V NAKED BATTERY.

NOTICE

Minimum distance to be kept between two drives: 20 cm.

Sunea 40 Solar io EN

2.1.Assembly

2.1.1.Preparing the drive

CAUTION

Sunea 40 Solar io : interior diameter of the tube has to be Ø37 mm or greater.

1] Fit the accessories required to integrate the drive into the tube:

Either only wheel (a) on the drive

or crown (b) and wheel (c) on the drive.

2] Measure the length (L) between the inner edge of the drive head and the rim

of the wheel.

L = …

Ø Ø Ø Ø

ab c

2.1.2.Preparing the tube

CAUTION

Install the drive in a tube with a minimum thickness of 0.5 mm and a smooth inner surface: with no welding, crimping,

folding, etc. inside the tube.

1] Cut the tube to the required length, depending on the motorised product.

2] Deburr the tube and remove the swarf.

3] For tubes which are smooth inside, cut a notch with the following

measurements:

d e

Ø 40 x 1 6mm 8.5mm

Ø 40 x 1.5 7mm 8.5mm

d e

2.1.3.Assembling the drive-tube

1] Slide the drive into the tube. For tubes with a smooth interior, position the cut

notch on the crown.

2] The wheel must be locked in place to prevent any movement in the tube.

•

This can be achieved by fastening the tube to the wheel using 4 self-tapping screws, Ø 5 mm, or 4steel pop

rivets, Ø4.8mm, placed between 5mm and 15mm from the outer edge of the wheel, regardless of the tube.

CAUTION

The screws or pop rivets must only be fastened onto the wheel and not on the drive.

EN Sunea 40 Solar io

2.1.4.Installing the drive-tube assembly

CAUTION

The motorised product must not be compressed between the brackets.

1] If necessary, screw the bracket adapter to the drive head (f).

2] Assemble and fix the drive-tube assembly onto the end bracket (g) and onto

the drive bracket (h).

CAUTION

Ensure that the drive-tube assembly is secured onto the end bracket. This operation prevents the tube-drive

assembly from coming out of the end bracket attachment.

2.1.5.Installation of the antenna

For optimal radio reception, it is recommended that the drive antenna extends at

least 10 cm outside of the motorised product housing and at least 1 cm from all

metal surfaces.

To fix the drive antenna in the ideal position, it is recommended to use the Somfy

MOUNTED ANTENNA BRACKET accessory.

≥1 cm

≥10 cm

CAUTION

•

Do not wind or cut the antenna wire. Observe a minimum bending radius (i) of 9mm.

•

Do not protrude the antenna wire from the side of the valances (risk of cutting the antenna)!

2.2.Wiring

WARNING

•

To ensure electrical safety, this Class III drive must be powered by a «SELV» voltage source (Safety Extra Low

Voltage).

•

Improper using battery pack may cause overheat, fire, explosion, resulting in serious injury or death.

•

Do not expose the drive or battery to excessive temperatures.

•

There is a risk if terminals of the battery-operated drive or battery being short circuited by metal objects.

PRECAUTION

•

Cables routed through a metal wall must be protected and insulated by sleeving or sheathing.

•

Secure the cables to prevent any contact with moving parts.

•

If the drive is used outdoors and if the power supply cable is of the H05-VVF type or PVC type, run the cable in a

UV-resistant duct, e.g. trunking.

•

The drive cable cannot be removed. If it is damaged, return the drive to the After-Sales department.

CAUTION

•

The cable between the drive and the battery must not exceed 2.5m (with wire cross-section min. 0.75mm²). For

lengths longer than 2.5m, it is recommended to use an extension cable with a larger cross section.

•

Leave the drive power supply cable accessible: the product must be easily replaceable.

•

Always make a loop in the power supply cable to prevent water from entering the drive.

Sunea 40 Solar io EN

CAUTION

•

Ensure battery is fully charged prior to installation on site.

•

Do not unplug the battery when the drive works.

•

For the purposes of recharging the battery, only use the detachable supply unit provided with this drive.

2.2.1.Wiring with connectors

1] Wire the 4-pin drive connector (j) to the 4-pin cable Y connector (k).

2] Wire the 2-pin cable Y connector (m) to the 2-pin battery connector (o).

3] Wire the 4-pin cable Y connector (p) to the 2-pin solar panel connector (q).

j k

p q

m o

2.2.2.Wiring without connectors

Wire the drive to the Oximo WireFree Battery, Oximo WireFree Battery Stick or Somfy 12V NAKED BATTERY battery (r)

and the 3.2 W Solar Panel solar panel (s), following the figure:

▪

L = Blue wire (+)

▪

N = Brown wire (-)

▪

SP = Yellow wire.

The wires must have a minimum conductor cross-section of 0.5mm2.

EN Sunea 40 Solar io

2.3.Commissioning

Identifying the steps to follow

The end limit setting depends on the type of motorised product:

Step 1: Pre-programming the control point [⇢2.3.1.]

Step 2: Checking the direction of rotation [⇢2.3.2.]

For a motorised

product with upper end

stops

The end limits must be set in semi-automatic

mode.

For a motorised

product without upper

end stops

The end limits must be set in manual mode.

Step 3 a:

Setting the end limits in semi-automatic mode

(for a motorised product with upper end stops)

[⇢2.3.3.1.]

Step 3 b:

Setting the end limits in manual mode [⇢2.3.3.2.]

Step 4: Programming the control point [⇢2.3.4.]

Use and maintenance [⇢3.]

NOTICE

For information about the compatibility of the drive with the motorised product and accessories, contact the product

manufacturer or Somfy.

Sunea 40 Solar io EN

2.3.1.Pre-programming the control point

1] Connect the drive to the battery, referring to Wiring.

2] Press the Up and Down buttons simultaneously on the control point:

The motorised product moves up and down.

The control point is pre-programmed.

1] 2]

2.3.2.Checking the direction of rotation

Press the Up button on the control point:

a] If the motorised product rises, the direction of rotation is correct: move onto

section Setting the end limits.

b] If the motorised product lowers, the direction of rotation is incorrect: move onto

the next step.

b1] Press the my button on the control point until the motorised product moves up

and down: The direction of rotation has been modified.

b2] Press the Up button on the control point to check the direction of rotation.

b1] b2]

2.3.3.Setting the end limits

2.3.3.1. Setting the end limits in semi-automatic mode (for a motorised product with

upper end stops)

The lower end limit must be set in manual mode, and the upper end limit is set

automatically:

1] Lower the motorised product to the desired position by pressing the Down

button.

Pressing and holding the Down button for more than 2 seconds will lower

the motorised product in one continuous movement.

2] Stop the motorised product at the desired point.

3] If necessary, adjust the position of the motorised product using the Up or

Down buttons.

4] Press the my and Up buttons simultaneously until the motorised product

rises.

The lower end limit is set.

5] Press the my button briefly to stop the motorised product.

6] To confirm the end limits, press the my button until the motorised product

briefly moves up and down.

The end limits are programmed.

1] 2]

2.3.3.2. Setting the end limits in manual mode

NOTICE

The end limits can be set in any order.

EN Sunea 40 Solar io

1] Raise the motorised product to the desired upper position by pressing the Up

button.

Pressing and holding the Up button for more than 2 seconds will rise the

motorised product in one continuous movement.

2] Stop the motorised product at the desired point.

3] If necessary, adjust the position of the motorised product using the Up or

Down buttons.

4] Press the my and Down buttons simultaneously until the motorised product

moves.

The upper end limit is memorized.

5] Press the my button briefly when the motorised product reaches the desired

lower position.

6] If necessary, adjust the down position using the Up and Down buttons.

Pressing and holding the Down button for more than 2 seconds will lower

the motorised product in one continuous movement.

7] Press the my and Up buttons simultaneously until the motorised product

moves.

The lower end limit is memorized. The motorised product rises and stops

in the upper position.

8] To confirm the end limits, press the my button until the motorised product

briefly moves up and down.

The end limits are programmed.

1] 2]

2.3.4.Programming the control point

The drive is in programming mode:

▪

Briefly press the PROG button on the control point to be programmed:

◦

The motorised product moves up and down.

→ The control point is programmed in the drive.

0.5 s

PROG.

NOTICE

If the drive is no longer in programming mode, repeat Step Pre-programming the control point before performing Step

Programming the control point [

}

10].

2.3.5."Back impulse" function

NOTICE

- This function allows the fabric to be stretched after each opening movement of the motorised product. It can be

adjusted up to ½ turn of the tube of the motorised product.

- This function can only be activated once the end-limit setting of the drive is completed.

Otros manuales para Sunea 40 Solar io

Tabla de contenidos

Idiomas:

Otros manuales de Accionamiento de CC de SOMFY

SOMFY

SOMFY Sunea 40 RTS DC Manual de usuario

SOMFY

SOMFY Orea RTS Series Manual de instrucciones

SOMFY

SOMFY Sonesse 40 Zigbee Manual de usuario

SOMFY

SOMFY HOME MOTION Orea WT Series Manual de usuario

SOMFY

SOMFY Roll Up 28 WireFree RTS Manual de usuario

SOMFY

SOMFY S&SO-RS100 io Manual de usuario

SOMFY

SOMFY Maestria WT Series Manual de usuario

SOMFY

SOMFY ILMO 2 40 WT Manual de usuario

SOMFY

SOMFY Sonesse Ultra 50 Manual de usuario

SOMFY

SOMFY Dexxo Compact RTS Manual de usuario

SOMFY

SOMFY ilmo2 50 WT Manual de usuario

SOMFY

SOMFY SONESSE 30 WF RTS LI-ION Manual de usuario

SOMFY

SOMFY mMotion Plus Manual de usuario

SOMFY

SOMFY Sonesse 28 WF Zigbee Manual de usuario

SOMFY

SOMFY ALTUS RS 50 io Manual de usuario

SOMFY

SOMFY Sonesse 28 WireFree RTS Li-ion Manual de usuario

SOMFY

SOMFY Sonesse 28 WF Zigbee Manual de usuario

SOMFY

SOMFY FTS50 Instrucciones de montaje

SOMFY

SOMFY Sonesse ULTRA 30 WireFree RTS Li-ion Instrucciones de funcionamiento

SOMFY

SOMFY ILMO2 50 io Manual de usuario

SOMFY

SOMFY J4 WT Manual de instrucciones

SOMFY

SOMFY Sonesse 30 DCT Manual de usuario

SOMFY

SOMFY S&SO-RS100 io Manual de usuario

SOMFY

SOMFY Sonesse Ultra 50 RS485 Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

Beckhoff

Beckhoff AX8911 Manual del operador