Solomend HD PVR 800 Manual de usuario
0
HD PVR 800
==============
Solomend DVB-S2 High Definition
Set Top Box
=================
User Manual
1
Safety Instructions
This product has been manufactured to applicable the international safety
standards. Please read all of safety and operating instructions before
operating the product and keep this manual for future reference.
Main Power Supply
AC 90-250V, 50/60Hz, Operate your product only from the type of power
supply indicated on the marking label. If you are not sure of the type of
power supplied to your home, consult your local power Company.
Disconnect the STB from the mains before you start any maintenance or
installation.
Overloading
Do not overload a wall outlet, extension cord or adapter as this may result
in electric fire or shocks.
Liquids
The product should not be exposed to any liquids such as dripping or
splashing. No objects filled with liquids, such as vases, should be
placed on the apparatus.
Cleaning
Before cleaning, disconnect the product from the wall outlet. Use a cloth
lightly dampened with water (no solvents) to clean the exterior.
Ventilation
The slots on top of the product must be left uncovered to allow proper
airflow to the unit. Do not stand the product on soft furnishings or
carpets. Do not expose the product to direct sunlight, place it near a
heater. Do not stack electronic equipment on top of the product.
Attahents
Do not use any attachment that is recommended by the manufacturer, it may
cause a hazard or damage the product.
Connection to the satellite dish LNB
Disconnect the product from the mains before connecting or disconnecting
the cable from the satellite dish. Failure to do so can damage the LNB.
Connection to the TV
Disconnect the product from the mains before connecting or disconnecting
the cable from the satellite dish. Failure to do so can damage the TV.
Location
Place the product indoors in order not to expose to lightning, rain or
sunlight .Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifier) that product heat.
Lighting or not in use
Unplug the produce from the wall outlet and disconnect the cable during a
lighting storm or when unused for a long time.
Servicing
Do not attempt service this product yourself, as opening or removing covers
may expose you to dangerous voltage or other hazard. Refer all servicing to
qualified service personnel.
"The mains plug is used as the disconnect device. The disconnect device
shall remain Readily operable."
2
Safety Precaution
CAUTION:
The lightning flash with arrowhead Warning: The exclamation point within
an symbol, within an equilateral triangle, To reduce the risk of electric shock,
equilateral triangle is intended to is intended to alert the user to don't open the
cabinet. Refer alert the user to important operating "dangerous voltage" and to
prevent servicing to qualified personnel only.and maintenance (servicing). from
a risk of electric shock.
WARNING:
Do not use this STB where contact with or immersion in water is a possibility.
Do not use near flower vase, washbowls, kitchen sinks, laundry tubs,
swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise,
there is the danger of fire.
WARNING: The unit should be connected to a power supply only of the type
described in the operating instructions or as marked on the unit. If you are not
sure of the type of power supply (for example, 120 or 230 V) to your home,
consult your local dealer or local power company.
WARNING: This product installs diodes. Do not open the cabinet or touch any
parts in the inner mechanism. Consult your local dealer for technical service if
the opening is required.
Note: To ensure proper use of this product, please read this User manual
carefully and retain for further reference.
Note: This product installs diodes. Do not open the cabinet to avoid the unit
direct exposure to radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet,
panel and remote control with a soft cloth lightly moistened with a mild
detergent solution.
3
Attachments: Never add any attachments and/or equipment without the
manufacturer consent; as such additions may result in the risk of fire, electric
shock, or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to
protect it from overheating. Do not block these openings or allow them to be
blocked by placing the STB on a bed, sofa, or other similar surface, nor should
it be placed over a radiator or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it
will not be walked on. Please take special attentions to cords at plugs,
convenience receptacles, and the point where they exit from the unit.
Object and Liquid Entry: Never put objects of any kind into this STB through
openings, as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill any liquid on the STB.
Note: Moisture may be formed on the lens In the following conditions:
¾when the unit is suddenly moved from a cold environment or an
air-condition room to a warm place.
¾Immediately after a heater has been turned on.
¾In a steamy or very humid room.
If the moisture forms inside the unit, it may not operate properly. To correct this
problem, turn on the power and wait about two hours for the moisture to
evaporate.
Parts Replacement: When the unit parts need to be replaced, user should
make sure the service technician use the replacement parts specified by the
manufacturer or having the same characteristics as the original part.
Unauthorized replacement may put the unit In the risk of fire, electric shock or
other hazards.
Safety Check: After all the maintenances and repairs are done, user is required
to request the service technician to conduct the overall safety check to ensure
the machine is In the proper condition.
4
Features
Accessories Main board (DB-M3602-02V01), ALi 48 Keys IR
controller, USB HDD BOX(customer option)
Board configuration 396MHz MIPS CPU, 128MB DDR400 RAM,
Memory Clock 198Mhz, 2MB Serial Flash, Single
Tuner, DVB-S2 demodulator,
Power Supply Input 100V ~ 240V 50/60Hz
Power Consumption 30W Max / 1W Standby (it’s optional by
customer’s board)
RS232 For FW Upgrading.
Receiver Standard DVB-S2 Standard (ETSI EN 302 307)
Input Frequency Range 950MHz ~ 2150Mhz
Input Signal Level -25dBm ~ -65dBm
Demodulation QPSK, 8PSK, 16APSK
Transport Stream MPEG-2 ISO/IEC 13818 Transport Stream
Specification
MPEG Profile Level MPEG2 SD, MPEG2 HD, H.264/AVC SD,
H.264/AVC HD
LNB Power & Polarization Vertical +13.5V, Horizontal 18V, Current: MAX
500ma,
Multi Satellite receiving 22K switcher, DiSEqC1.0, DiSEqC1.1,
Unicable , DiSEqC1.2, USAL
Conditional Access system 1 Common Interface Slots ; 1 CA card reader
Slots
A/V Output ports YPrPb, RCA with CVBS, SCART with CVBS,
HDMI(HDCP), Left/Right analog audio
output(RCA), Digital audio output(SPDIF with
coaxial or fiber)
Aspect Ratio Auto, 16:9 Pillar box, 4:3 Pan & Scan, 4:3 Letter
Box.
Audio Decoding MPEG1 layer I, MPEG1 layer II, MPEG1 layer
III, MPEG2, AC3.
Audio Mode Stereo/MONO/Left/Right
DVR supporting DVR with USB HDD, Time shifting with USB
HDD
USB2.0 High Speed HOST 1 USB2.0 Port, USB media player to playback the
media in USB flash disk or USB
HDD or USB card reader with memory card or
FW Upgrading.
File system FAT12, FAT16, FAT32, NTFS (only support first
partition)
Media Supporting JPG, BMP, MP3, WMA
Ethernet Interface 10/100Mbit
Storage Temperature 0℃to +50℃
Operating temperature 5℃to +30℃
5
CONTENTS
1.REMOTECONTROL
2.BASICOPERATIONS
2.1TurnonSTB
2.2Power
2.3ChannelUP/Channeldown
2.4VolumeUP/VolumeDown
2.5Number
2.6Mute
2.7Pause
2.8Recall
2.9Favorite
2.10Audio
2.11Information
2.12EPG
2.13TV/RADIO
2.14ChannelList
2.15Sleep
2.16PageUP/PageDown
2.17MultiPicture
2.18TEXT
2.19Subttile
2.20Find
2.21Zoom
2.22TV/STB
2.23Menu
2.24Exit
3.CHANNEL
3.1TVChannelList
3.1.1.Favorite
3.1.2.Lock
3.1.3.Skip
3.1.4.Move
3.1.5.Edit
3.2RadioChannelList
3.3DeleteAll
6
4.INSTALLATION
4.1AntennaConnection
4.2SatelliteList
4.3AntennaSetup
4.4Singlesatellitesearch
4.5Multisatellitesearch
4.6TPLIST
4.7Other
5.SYSTEMSETUP
5.1Language
5.2TVSystem
5.3Localtimesetting
5.4Timersetting
5.5ParentalLock
5.6OSDsetting
5.7Favorite
6.Tool
6.1Information
6.2FactorySetting
6.3UpgradebyRS232
6.4COMMONINTERFACE
6.5UpgradeByUSB
6.6RemoveUSBDeviceSafety
7.NETWORKLOCALSETTING
7.1NETWORKLOCALSETTING
8.REC
8.1MUSIC&PICTURE
8.2RECORDMANAGER
8.2.1LOCK
8.2.2Delete
8.2.3Rename
8.3HDDInformation
8.4HDDFormat
8.5Timeshift
8.6Jump
7
Quick Start
Connect your STB to TV by A/V Cable. You have 3 methods.
Methods 1: If your TV is a standard definition TV and does not has
components input port, please use a 3 lines cable (yellow, red and white) to
connect your STB’s CVBS, Left analog audio port, right analog audio port
to your TV’s corresponding port.
Methods 2: If your TV is a standard definition TV but has components input
port or your TV is a High definition TV, you can connect your STB to your
TV with a 5 lines cable (Green, Blue, Red/ Red, white).
Methods 3: If your TV has HDMI input port, you can connect your STB to
your TV with a HDMI cable. resolution to be the max TV resolution.
Connect your Satellite Antenna cable to your STB’s LNB IN port. Then turn
on your TV and select a exact Input port by TV remote controller.
8
Turn on your STB power, select a satellite in satellite list menu and then
enter the Antenna setup to config exact parameters of this antenna, select
Single Satellite Search and select auto scan to search programs.
If you want to want to get high picture quality, please check how big
resolution could your TV support, and press V.Format key to switch your
STB output.
9
1. Remote Controller
Tabla de contenidos
