Sollae Systems P5H-151 Manual de usuario
P5H-151 User Manual > Introduction
2021-12-10 Sollae Systems page 1 of 13
Overview
The P5H-151 is a programmable device that provides Ethernet function. This product equipped with
an RS232 port so you can connect an RS232 device to a network.
Programming on this product requires the use of PHPoC (PHP on Chip). PHPoC is quite similar in
syntax to PHP, the general-purpose scripting language. Therefore, anyone with experience in
programming can easily learn and use it.
※ Although PHPoC and PHP are quite similar in syntax, they are clearly different programming
languages. Refer to the PHPoC Language Reference and PHPoC vs PHP for detailed information.
P5H-151 User Manual > Features
2021-12-10 Sollae Systems page 2 of 13
Features
self-developed PHPoC interpreter
simple development environment via USB
10/100Mbps Ethernet
an RS232 Port
5 user-defined LEDs
self-developed TCP/IP stacks
Web Server
WebSocket, TLS
various libraries (Email, DNS, MySQL and Etc.)
dedicated development tool (PHPoC Debugger)
P5H-151 User Manual > H/W Specification
2021-12-10 Sollae Systems page 3 of 13
H/W Specification
H/W Specification
Power Input Power DC Jack, 5V (±0.5V)
Current Consumption typical - approximately 273mA
Dimension 89mm x 57mm x 24mm
Weight approximately 69g
Interface
Serial Port D-SUB 9-pin Male Connector,
an RS232 port
Network 10/100Mbps Ethernet
USB USB Device Port - for PC connection
LED 9 LEDs (System: 4, User-defined: 5)
Temperature (storage/operating) -40℃ ~ 85℃
Environment RoHS Compliant
P5H-151 User Manual > Layout
2021-12-10 Sollae Systems page 4 of 13
Layout
1. Supplying Power
DC 5V Input
This port is the input port for supplying power. The input voltage is DC 5V(±0.5V) and the
specification is as follows:
P5H-151 User Manual > Layout
2021-12-10 Sollae Systems page 5 of 13
2. Ethernet
Ethernet port supports 10/100Mbps Ethernet. This port is an RJ45 connector and it is mapped to
NET0 for programming.
3. Serial Port
The type of serial port is an RS232. This port is a D-SUB 9-pin male connector and is mapped to
UART0 for programming.
pin assignment
Num Lable Description Level I/O Wiring
1 DCD Data Carrier Detect RS232 In Optional
2 RXD Receive Data RS232 In Required
P5H-151 User Manual > Layout
2021-12-10 Sollae Systems page 6 of 13
Num Lable Description Level I/O Wiring
3 TXD Transmit Data RS232 Out Required
4 DTR Data Terminal Ready RS232 Out Optional
5 GND Ground Ground - Required
6 DSR Data Set Ready RS232 In Optional
7 RTS Request To Send RS232 Out Optional
8 CTS Clear To Send RS232 In Optional
9 RI Ring Indicator RS232 In Optional
4. LED
This product has 9 LEDs. The user-defined LEDs are turned on when you output LOW to the UIO pin
connected.
Lable Color Description UIO pin
PWR Red System LED - supplying power N/A
STS Yellow System LED - system status N/A
L0 Green User-defined LED 0 UIO1.8
L1 Green User-defined LED 1 UIO1.7
L2 Green User-defined LED 2 UIO1.6
A Green User-defined LED 3 UIO0.30
B Green User-defined LED 4 UIO0.31
RJ45_G Green System LED - system status N/A
RJ45_Y Yellow System LED - network link status N/A
5. Function Button
The function button, which is inside the hole of the side panel, is used to operate this product as a
button setup mode.
6. USB Device Port for connection with PC
The USB device port is to connect with PC. You can access to P5H-151 via development tool by
connecting USB cable to this port.
P5H-151 User Manual > How to Use > Software(IDE)
2021-12-10 Sollae Systems page 7 of 13
Software (IDE)
PHPoC Debugger
PHPoC Debugger is a software used for developing and setting PHPoC products. You need to install
this program on your PC for using PHPoC.
PHPoC Debugger Download Page
PHPoC Debugger Manual
Functions and Features of PHPoC Debugger
Upload files from local PC to PHPoC
Download files in PHPoC to local PC
Edit files stored in PHPoC
Debug PHPoC scripts
Monitor resources of PHPoC
Configure parameters of PHPoC
Upgrade Firmware of PHPoC
Support MS Windows O/S
P5H-151 User Manual > How to Use > Connecting
2021-12-10 Sollae Systems page 8 of 13
Connecting Product
USB Connection
Connect the USB device port of P5H-151 to your PC via a USB cable.1.
Run PHPoC Debugger2.
Select connected COM PORT and press connect ( ) button.3.
If USB is successfully connected, connect button will be inactivated and disconnect button (4.
) will be activated
Remote Connection
P5H-151 provides the remote connection. Please refer to the PHPoC Debugger manual page for
details.
P5H-151 User Manual > How to Use > Reset
2021-12-10 Sollae Systems page 9 of 13
Reset
Settings Reset
Settings Reset makes all settings of your PHPoC products to factory default.
Settings Reset Procedure
Step Action Product State STS LED
1Press function button shortly (less than 1
second) Button setup mode On
2Keep pressing the function button over 5
seconds Preparing initialization Blink very
rapidly
3 Check if the STS LED is turned OFF Initialization ready Off
4
Release the function button right after the
STS is OFF.(※ If you don't release the
button within 2 seconds, the state go back
to the step 3)
Progressing
initialization On
5 Rebooting automatically Initial state Off
Factory Reset
Factory Reset makes all settings of your PHPoC products to factory default including a password.
Futhermore, all files stored in flash memory are deleted as well as certificate. Because of this, you
have to backup your files before doing Factory Reset. To progresss the Factory Reset, the PHPoC
Debugger is required.
Factory Reset Procedure
P5H-151 User Manual > How to Use > Web Interface
2021-12-10 Sollae Systems page 10 of 13
Web Interface
PHPoC itself has a webserver to provide a web interface. When receiving a HTTP request, it executes
the php script in the requested file (if there) and respond to the client. Webserver is independent of
PHPoC main script. TCP 80 is used for web server and you can use the interface via Internet Explorer,
Chrome or any other web browsers.
How to use web interface
To use the web interface, "index.php" file should be in the file system of your PHPoC. Connect to
this page by entering device IP address after connecting it to network.
If the name of file is not "index.php", just specify the name of file after the IP address with slash
mark.
Practical Use of Web Interface
Since the web server executes the php script in the requested file, user can put php code in the in
the requested file to interact with peripherals. It is worth noting that there is other way to interact
with the peripherals in real-time from web interface. This can be done by using websocket.
Tabla de contenidos
Otros manuales de Hardware de red de Sollae Systems
Sollae Systems
Sollae Systems EZL-50L Manual de usuario
Sollae Systems
Sollae Systems P5H-153 Manual de usuario
Sollae Systems
Sollae Systems SCG-5608 Manual de usuario
Sollae Systems
Sollae Systems EZL-80c Manual de usuario
Sollae Systems
Sollae Systems P5H-155 Manual de usuario
Sollae Systems
Sollae Systems CSE-T16 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
