Solid RocketWAVE SRF-L-8A1821 Manual de usuario

RocketWAVE™

SRF-L-8A1821

Product Manual

DEC 2021

V1.7

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

company private to SOLiD and should not be modified, used, copied, reproduced or disclosed in whole or in part

without the written consent of SOLiD.

Trademark Information

No right, license, or interest to SOLiD trademarks is granted here. By using this document, you agree not to as-

sert any right, license, or interest with respect to such trademark. Other product names mentioned in this manual

are used for identification purposes only and may be trademarks or registered trademarks of their respective

companies.

Disclaimer of Liability

The contents of this document, including graphics and screenshots, are current as of the date of publication.

SOLiD reserves the right to change the contents without prior notice. In no event shall SOLiD be liable for any

damages resulting from loss of data, loss of use or loss of profits. SOLiD further disclaims any and all liability for

indirect, incidental, special, consequential or other similar damages. This disclaimer of liability applies to all prod-

ucts, publications and services during and after the warranty period.

SOLiD GmbH, December 2021

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021 
© 2021 SOLiD, Inc. All Rights Reserved. Confidential & Proprietary. Page 3 
Contents 
 General................................................................................................................ 4 
1.1 Health and Safety..................................................................................................................................4 
1.2 Compliance...........................................................................................................................................5 
1.3 Technical Support .................................................................................................................................6 
 Introduction......................................................................................................... 7 
2.1 System Overview ..................................................................................................................................7 
 Service Frequency & Bandwidth.............................................................................................7 
 In/Output Power & Gain..........................................................................................................7 
 800MHz Adaptive band combinations.....................................................................................8 
2.2 Functions...............................................................................................................................................8 
 Repeater Interface ............................................................................................ 12 
 Package Configuration..................................................................................... 13 
 Installation......................................................................................................... 14 
5.1 Donor antenna installation...................................................................................................................14 
5.2 Repeater installation............................................................................................................................ 14 
5.3 USIM Installation.................................................................................................................................17 
 Software ............................................................................................................ 18 
6.1 LMT (DT_GUI) Installation ..................................................................................................................18 
6.2 LMT User Interface..............................................................................................................................19 
6.3 Firmware Upgrade...............................................................................................................................21 
 Appendix........................................................................................................... 22 
7.1 General specification........................................................................................................................... 22 
7.2 RF specification...................................................................................................................................22 
 Troubleshooting ............................................................................................... 24 
 
 
 
 

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

General

“Only qualified personnel are allowed to handle this unit. Read carefully and understand all the warning

labels attached in this user manual”. Any personnel involved in installation, operation or service of the

SOLiD repeaters must understand and comply the following:

Understand all general and regional installation and safety regulations relating to work on high voltage

installations, as well as regulations covering correct use of tools and personal protective equipment.

The power supply unit in repeaters contains dangerous voltage level, which can cause electric shock.

Switch the mains off prior to any work in such a repeater. Any local regulations are to be followed when

servicing repeaters.

The repeater cover should be (door) securely fastened in open position, e.g. bytying it up, at outdoor work

in order to prevent door from slamming due to wind causing bodily harm or damage.

Use this unit only for the purpose specified by the manufacturer. Do not carry out any modifications or fit

any spare parts which are not sold or recommended by the manufacturer. This could cause fires, electric

shock or other injuries.

Any repeater, including this repeater, will generate radio signals and thereby give rise to electromagnetic

fields that may be hazardous to the health of any person who is extensively exposed to the signals at the

immediate proximity of the repeater and the repeater antennas.

Due to power dissipation, repeater may reach a very high temperature. Do not operate this unit on or close

to flammable materials.

Do not use any solvents, chemicals, or cleaning solutions containing alcohol, ammonia, or abrasives.

For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily ac-

cessible.

This power of this system shall be supplied through wiring installed in a normal building. If powered directly

from the mains distribution system, it shall be used additional protection, such as overvoltage protection

device.

Round terminals located on the rear of a 1.0mm2 (16AWG) or more wires using permanently connected

to earth.

CAUTIONS

This is a class B product. In domestic environment, this product may cause radio interference in which

cause the user may be required to take adequate measures.



Do NOT open except at Approved Field Force Protective Work Station

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

Regulatory Compliance / Certifications for repeater

CE Radio Equipment Directive (RED) Directive

(2014/53/EU)

RF:

ETSI EN 301 908-15 V15.1.1

ETSI EN 301 908-1 V13.1.1 (2019-11)

EN50385:2017

EMC:

ETSI EN 301-489-1 V2.2.3

ETSI EN 301 489-50 V2.3.1

Safety:

EN IEC 62368-1 :2020+A11 :2020

RoHS

2011/65/EU Amended to 2015/863/EU

REACH

EC 1907/2006 REACH Regulation

Regulatory Compliance / Certifications for power supply

CE: EN60950-1 / 62368-1

Electrostatic Discharge Immunity:

IEC61000-4-2:2008

Radiation Electromagnetic Immunity

IEC61000=4-3:2006+A1:2007+A2:2010

FAST TRANSIENT IMMUNITY

IEC61000-4-4:2004

SURGE IMMUNITY

IEC61000-4-5:2005

CONDUCTED DISTURBANCES IMMUNITY

IEC61000-4-6:2008

VOLTAGE DIPS, INTERRUPTION & VARIATIONS

IEC61000-4-11:2004

The installation to comply with European EN50385 exposure compliance requirements, the following

Power Density limits/guidelines (mW/cm2) according to ICNIRP are valid:

- 0.2 for frequencies from 10 MHz to 400 MHz

- F (MHz) / 2000 for frequencies from 400 MHz to 2 GHz

- 1 for frequencies from 2 GHz to 300 GHz

The power supply of the unit complies with Overvoltage Category II. It also complies with the surge re-

quirement according to EN 61000-4-5 (fine protection); however, installation of an additional medium

(via local supply connection) and/or coarse protection (external surge protection) is recommended de-

pending on the individual application in order to avoid damage caused by overcurrent.

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

The repeater complies with European standard EN60950-1/EN62368-1.

To be sold exclusively to mobile operators or authorized installers - no harmonized fre-

quency bands, operation requires license. Intended use: EU and EFTA countries.

Indicates conformity with the RED directive 2014/53EU and/or RoHS directive 2011/65/EU.

Declaration of Conformity: SOLiD declares that the radio equipment type Repeater is in compliance

with Directive 2014/53/EU. The Full text of the EU declaration is available at the following website:

https://solid.com/emea/resources/product-literature/

WEEE Recycling: SOLiD complies with collection and recycling arrangements per the Waste Electrical

and Electronic Equipment (WEEE) Directive and implementing regulations. See more information at:

https://solid.com/emea/resources/product-literature/

For all technical support or product return requests, please ensure you have the SOLiD product identification and

serial number available. These can be found located on the back of the unit. The site and customer name should

also be included in all communications. All faulty units must be returned in their original or suitable protective

packaging.

Please contact SOLiD the local office or send an email via one of the following email addresses:

SOLiD EU GmbH

Gartenstr. 5, 87448 Waltenhofen, Germany

[email protected]

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

Introduction

SOLiD RocketWAVE™ SRF-L-8A1821 is a compact repeater with low-power consumption supporting the three

different radio frequency bands that designed to enhance the coverage in area such home and small of-

fice(SOHO). The device supports the mobile/cellular frequency in B20(800) with adjustable filter / B3(1800) /

B1(2100) for 4G LTE and 5G NR NSA. With its compact plug & play design, installation of the device is easy and

quick. For European market, the device complies the various standard and regulation such as CE, RoHS, Fire-

load, etc. The device comes with various embedded function and feature for the stable and sustainable O&M.

The LTE modem is embedded in the device that support NMS by communicating through LTE signal. System

operation can be monitored by carrier NMS in NoC. And through this NMS feature, the device S/W can be easily

upgraded and fix when there is a case. Implementing with this features, user is able to experience the service

with good quality.

Service Frequency & Bandwidth

Frequency & Bandwidth

Downlink (TX)

Uplink (RX)

Band 20

800 MHz

Service Frequency

791 to 821 MHz

832 to 862 MHz

Bandwidth

5 / 10 MHz

Band 3

1800 MHz

Service Frequency

1805 to 1835 MHz

1710 to 1740 MHz

Bandwidth

30 MHz

Band 1

2100 MHz

Service Frequency

2150 to 2170 MHz

1960 to 1980 MHz

Bandwidth

20 MHz

In/Output Power & Gain

Item

Downlink (TX)

Uplink (RX)

Input Level

Gain

Output

Input Level

Gain

Output

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

Min.

Max.

Min.

Max.

Power

Min.

Max.

Min.

Max.

Power

800MHz

-54dBm

-24dBm

34dB

64dB

+10dBm

-46dBm

-16dBm

34dB

64dB

+18dBm

1800MHz

-52dBm

-22dBm

34dB

64dB

+12dBm

-46dBm

-16dBm

34dB

64dB

+18dBm

2100MHz

-51dBm

-21dBm

34dB

64dB

+13dBm

-46dBm

-16dBm

34dB

64dB

+18dBm

800MHz Adaptive band combinations

Channel

Downlink (TX)

Uplink (RX)

Bandwidth

low

center

high

low

center

high

5 MHz

791MHz

793.5 MHz

796 MHz

832 MHz

834.5 MHz

837 MHz

796 MHz

798.5 MHz

801 MHz

837 MHz

839.5 MHz

842 MHz

801 MHz

803.5 MHz

806 MHz

842 MHz

844.5 MHz

847 MHz

806 MHz

808.5 MHz

811 MHz

847 MHz

849.5 MHz

852 MHz

811 MHz

813.5 MHz

816 MHz

852 MHz

854.5 MHz

857 MHz

816 MHz

818.5 MHz

821 MHz

857 MHz

859.5 MHz

862 MHz

10 MHz

791 MHz

796 MHz

801 MHz

832 MHz

837 MHz

842 MHz

796 MHz

801 MHz

806 MHz

837 MHz

842 MHz

847 MHz

801 MHz

806 MHz

811 MHz

842 MHz

847 MHz

852 MHz

806 MHz

811 MHz

816 MHz

847 MHz

852 MHz

857 MHz

811 MHz

816 MHz

821 MHz

852 MHz

857 MHz

862 MHz

The following block diagram describes the operation principle, how the repeater works (e.g. 1.8GHz frequency

range (b3)).

Isolation Check and Gain Limitation

B3 DPX

LNA

AGC

ALC

AGC

ISO

SAW AMP PAD MIXER MIXER

AMP AMP

SAW

SAW PAD

DL MUX

UL MUX

SAW

B3 UL Path

B3 DL Path

PAD

AMP

MIXER

AMP

SAW

AMP

MIXER

SAW

B3 PLL

PAD AMP

B3_PLL #1

B3_PLL #2

B3_PLL #3

B3_PLL #4

DET DET

B3_PLL #1

B3_PLL #3

B3_PLL #4

T-PAD T-PAD

DET

AMP

T-PAD T-PAD

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

This function is that measuring the DL isolation value between donor antenna and service antenna during the

initialization process and setting the gain value for the repeater operation. If the measured values does not satisfy

the operating condition, the repeater is shutting down. Basically the gain value for DL/UL must be maintained un-

der [DL Isolation –15dB (±3dB)]. This process is applied to all service bands. Isolation Check is done within 30

seconds and Recheck is done within 10 seconds.

When a repeater is turned on, the system performs Isolation Check 3 times. The gain value is determined by re-

ferring to the lowest value among the three measured isolation values. If any one of these measured values does

not satisfy with operating condition (= satisfy shutting down condition), the value is excluded to the reference for

the gain value. And the repeater is shutting down.

If there occurs fluctuation in output power, more than 10 dB for 10 seconds over 5 times, the repeater performs

Isolation Recheck and set gain value properly for the last measured isolation value. After 1 hour, the repeater

performs Isolation Check one more time and set the gain value again.

Once the repeater starts to operate, the system performs the Isolation Check process one more time, once a day.

During the Isolation Recheck, the repeater is not going to shut down. If the isolation oscillation occurs while the

repeater is operating in the minimum gain value, Over-output Shutdown function performs to protect the repeater

and this time, the gain value is set to the minimum value if DL/UL gain is not under [DL Isolation -15dB (±3dB)].

Repeater Shutdown?

A repeater is shutting down when following conditions:

- DL input power is under -36dBm/Total, and measured isolation value is under 60dB.

- DL input power is over -36dBm/Total, and measured isolation value is under [DL/UL Gain + 15dB].

- Measured all 3 values satisfy above conditions.

Automatic Gain Control (AGC)

This function is that controlling gain value to maintain DL output power is [user setting value ±2 dBm] when

each service band’s DL input power is within rated range. The UL Gain must be maintained [DL Gain ±2 dB]. If

the Isolation ATT value is set due to Isolation Check, the repeater can control AGC ATT within [30dB - Isolation

ATT]. The DL In/Output and DL/UL Gain value for AGC operation is described as follows.

[B20 800 MHz]

DL Input (RSSI)

DL Output

DL Gain

UL Gain

-59 dBm

5 dBm

64 dB

-54 dBm

10 dBm

64 dB

-49 dBm

10 dBm

59 dB

-44 dBm

10 dBm

54 dB

-39 dBm

10 dBm

49 dB

-34 dBm

10 dBm

44 dB

-29 dBm

10 dBm

39 dB

-24 dBm

10 dBm

34 dB

SOLiD RocketWAVE™ SRF-L-8A1821 Product Manual V1.7 - DEC 2021

[B3 1800 MHz]

DL Input (RSSI)

DL Output

DL Gain

UL Gain

-57 dBm

7 dBm

64 dB

-52 dBm

12 dBm

64 dB

-47 dBm

12 dBm

59 dB

-42 dBm

12 dBm

54 dB

-37 dBm

12 dBm

49 dB

-32 dBm

12 dBm

44 dB

-27 dBm

12 dBm

39 dB

-22 dBm

12 dBm

34 dB

[B1 2100 MHz]

DL Input (RSSI)

DL Output

DL Gain

UL Gain

-57 dBm

8 dBm

64 dB

-51 dBm

13 dBm

64 dB

-46 dBm

13 dBm

59 dB

-41 dBm

13 dBm

54 dB

-36 dBm

13 dBm

49 dB

-31 dBm

13 dBm

44 dB

-26 dBm

13 dBm

39 dB

-21 dBm

13 dBm

34 dB

Auto Level Control (ALC) for UL over-input

This function is that preventing and maintaining the signal quality degradation due to UL’s over input power satu-

ration. The attenuator is located after UL Low Noise Amplifier (LNA). The UL In/Output and UL Gain for ALC op-

eration is described as follows.

[B20 800MHz / B3 1800MHz / B1 2100MHz]

UL Input (RSSI)

UL Output

UL Gain

-46dBm

18dBm

64dB

-41dBm

18dBm

64dB

-36dBm

18dBm

59dB

-31dBm

18dBm

54dB

-26dBm

18dBm

49dB

-21dBm

18dBm

44dB

-16dBm

18dBm

39dB

ALC for UL over-output

Tabla de contenidos

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario