Solid State Logic Duality Fuse Instrucciones de montaje
Installation and Setup Guide
Duality Fuse
Installation and Setup
Guide
82BDYG01F
Duality Fuse
Visit SSL at:
www.solidstatelogic.com
© Solid State Logic
All rights reserved under International and Pan-American Copyright Conventions
SSL®and Solid State Logic®are ® registered trademarks of Solid State Logic.
Fuse™, Fusion™, SuperAnalogue™, Duality™ and VHD™ are all trademarks of Solid State Logic.
All other product names and trademarks are the property of their respective owners and are hereby acknowledged.
No part of this publication may be reproduced in any form or by any means, whether mechanical or electronic, without the
written permission of Solid State Logic, Oxford, OX5 1RU, England.
As research and development is a continual process, Solid State Logic reserves the right to change the features and speci-
fications described herein without notice or obligation.
Solid State Logic cannot be held responsible for any loss or damage arising directly or indirectly from any error or omission
in this manual.
PLEASE READ ALL INSTRUCTIONS, PAY SPECIAL HEED TO SAFETY WARNINGS.
E&OE
October 2020
Contents
Section 1 – Introduction 5
About This Manual 5
Symbols Used 5
Contacting SSL 5
Section 2 – Safety Information 6
Denitions 6
Installation Instructions 7
Voltage Selection and Fusing 7
Safety Earth Connection 7
Mains Supply and Phases 7
Mains Isolation and Over-Current Protection 7
Physical Safety 7
Standards Conformance 8
FCCCertication 8
Instructions for Disposal of WEEE by Users in the EU 8
Section 3 – Preparation 9
Services Available From SSL 9
Shipment 9
Commissioning 9
Training 9
Factory Warranty 9
Extended Warranty 9
Physical Requirements 10
Console Control Surface Layout 10
Patchbay Options 10
PatchbayConnectors–D25orDL96 10
Cable Access and Ducting 11
Thermal Considerations 11
Service Access 11
System Options 12
Table Of Contents
Page 1
Duality Fuse Installation & Setup Guide
Page 2 Duality Fuse Installation & Setup Guide
Table of Contents Section 1
Technical Requirements 13
Sync Source 13
Power Connections 13
UPS Provision 13
Air Conditioning 13
Grounding 13
Workstation interface 13
Section 4 – Installation 15
Unpacking The Console 15
Attaching the legs 15
Removing/ttingthetrim 15
Front Buffer 15
End Trim 15
Top Trim 15
Console reassembly 17
Removing Channel Strips and Panels 17
Cable Connections 17
Section Assembly 19
Power Connection 21
PSU Redundant consoles 21
UPS Provision 21
Audio Connections – No Patchbay 23
Channel Connections 23
Centre Section Connectors 23
Fusion Section Connectors 23
Audio Connections – With Patchbay 25
Internal Patchbay 25
Remote Patchbay 25
AudioConnections–FusionProcessing 26
Fusion Connection Using Patchbay 27
Fusion Connection Without Patchbay 28
Flash Card 30
Red Light/Talkback and User Switch GPIO Connector 30
Page 3
Duality Fuse Installation & Setup Guide
Section 1 Table of Contents
Footswitch Connection 30
TFT Monitor Arm Attachment (option) 31
ArmSpecications 31
Section 5 – Connecting Your DAW 33
Overview 33
Installing the ipMIDI Driver and Logictivity Browser 34
ipMIDI Software Installation (For Macintosh) 34
ipMIDI Software Installation (For PC) 34
Ethernet Network Setup 35
Duality’s IP Address 35
DirectNetworkConnection(Macintosh) 36
Direct Network connection (PC) 37
Network Connection Using DHCP 38
Larger Networks and ipMIDI 39
Assigning Duality’s Fixed IP Address 40
Network trouble shooting 40
Using Physical MIDI Ports to Connect your DAW 41
Enabling ipMIDI on your Duality Fuse 43
The δ-Ctrl Plug-In 43
Setting workstation(s) to communicate via ipMIDI 44
Workstation Setup – Pro Tools 45
WorkstationSetup–LogicProX 46
Finding a console on the Duality Remote application 48
Enabling the Logictivity features on your console 48
AppendixA–Specications 50
Appendix B – Connector Details 51
Appendix C – Connector Pinouts 52
Appendix D – Patchbay Layouts 57
AppendixE–ConsoleFootprints 62
AppendixF–EnvironmentalSpecication 67
Page 4 Duality Fuse Installation & Setup Guide
Table of Contents Section 1
Blank page
Section 2 Safety Information
Page 5
Duality Fuse Installation & Setup Guide
Section 1 – Introduction
About This Manual
The object of this manual is to provide owners and installers of the Solid State Logic (SSL) Duality Fuse console with
information in the following areas:
Section 2 Safety Information – Please read this section as it includes important information relating to the
electrical supply requirements and to physical safety.
Section 3 Preparation – Provides detail about the console and its optional components and also what
preparation is necessary relating to the proposed location and any peripheral equipment that may be
required. Some items and services will need to be supplied by the facility.
Section 4 Installation – Provides instructions relating to cabling and connection for the console and its optional
items.
Section 5 Connecting Your DAW – Provides step-by-step instructions on how to physically connect your
DAW plus the console and workstation conguration settings.
Appendices Specications, connector pinouts, conguration details and useful guidelines.
The information provided by this manual is relevant to all frame sizes of the Duality console.
Symbols Used
Electrical safety hazard.
General safety warning.
Indicates that it is the responsibility of the facility to provide this item or service.
Important, useful or otherwise noteworthy information will be indicated inside a border
Indicates that additional information may be located on another page or in an Appendix.
Contacting SSL
Information relating to support for the Duality console is available on the internet:
www.solidstatelogic.com/products/duality
The latest version of this manual can be downloaded from:
https://www.solidstatelogic.com/products/duality?tab=documents
Safety Information Section 2
Page6 Duality Fuse Installation & Setup Guide
Section 2 – Safety Information
This section contains denitions and warnings, and practical information to ensure a safe working environment. Please take
time to read this section before undertaking any installation work.
Denitions
‘Maintenance’
All maintenance must be carried out by fully trained personnel. Note: It is advisable to observe suitable ESD
precautions when maintenance to any part is undertaken.
‘Non-User Adjustments’
Adjustments or alterations to the equipment may affect the performance such that safety and/or international
compliance standards may no longer be met. Any such adjustments must therefore only be carried out by fully trained
personnel.
‘Users’
This equipment is designed for use solely by engineers and competent operators skilled in the use of professional
audio equipment.
‘Environment’
This product is a class A product intended to form an integrated component part of a professional audio recording,
mixing, TV, radio broadcast or similar studio wherein it will perform to specication providing that it is installed
according to professional practice.
Electrical Safety Warning
When installing or servicing any item of SSL equipment with power applied, when cover panels are
removed, HAZARDOUS CONDITIONS CAN EXIST.
These hazards include: • High voltages
• High energy stored in capacitors
• High currents available from DC power busses
• Hot component surfaces
Any metal jewellery (watches, bracelets, neck-chains and rings) that could inadvertently come into contact
with uninsulated parts should always be removed before reaching inside powered equipment.
Tabla de contenidos
Otros manuales de Mezclador de música de Solid State Logic
Solid State Logic
Solid State Logic C300 HD Manual de usuario
Solid State Logic
Solid State Logic Nucleus2 Manual de usuario
Solid State Logic
Solid State Logic C100 HDS Manual de usuario
Solid State Logic
Solid State Logic Matrix Manual de usuario
Solid State Logic
Solid State Logic XL-Desk Manual de usuario
Solid State Logic
Solid State Logic Sigma Manual de usuario
Solid State Logic
Solid State Logic AWS 900+ Manual de usuario
Solid State Logic
Solid State Logic Duality SE Manual de usuario
Solid State Logic
Solid State Logic Sigma Delta Manual de usuario
Solid State Logic
Solid State Logic C200 HD Manual de usuario
Solid State Logic
Solid State Logic Duality Manual de usuario
Solid State Logic
Solid State Logic AWS 900 Manual de uso y cuidado
Solid State Logic
Solid State Logic AWS 924 Manual de usuario
Solid State Logic
Solid State Logic SiX Manual de usuario
Solid State Logic
Solid State Logic BiG SiX Manual de usuario
Solid State Logic
Solid State Logic C100 HDS Manual de usuario
Solid State Logic
Solid State Logic C100 HD Range Manual de usuario
Solid State Logic
Solid State Logic SL 9000 J SERIES Manual de usuario
Solid State Logic
Solid State Logic C100HDSS Manual de usuario
Solid State Logic
Solid State Logic ORIGIN Manual de usuario
