Solid Apollo SA-PROF-CROWN-78 Manual de usuario
PRODUCT MANUAL
78” Crown Molding LED Strip Channel
Installation Guide
Contact Us: 425.582.7533
www.SolidApollo.com
Andrew@SolidApollo.com
page 1
™
Install the Crown Molding LED Strip Channel Raceway Base with 2-3 screws per section.
Please Note: The Channel Raceway can be cut to length.We strongly advise that you leave 1/4 inches of gap between Channel Raceway
Base sections at the start of each lighting placement (see illustration below).
The 1/4 inch gap provides space for extra/future connections and as you interconnect LED strips together, the excess wires can be set discreetly
onto the Channel Raceway base see Step 2 illustration for more details.
Step 1: Install Crown Molding LED Strip Channel Raceway Base
Installation Guide
Channel Raceway Base
Crown Molding
LED Strip
LED Strip
Channel Raceway Base
Install Screws
1/4 in Gap
Carefully install the LED strip in the Crown Molding LED Strip Channel.
Please Note: If you are interconnecting another strip or channel (please follow instruction on Step 1),
excess wires can be set discreetly onto the Channel Raceway base see illustration below.
Step 2: Install the LED strip into the Crown Molding LED Strip Channel
Place excess LED strip
wires in the Channel
Raceway Base.
PRODUCT MANUAL
78” Crown Molding LED Strip Channel
Installation Guide
Contact Us: 425.582.7533
www.SolidApollo.com
Andrew@SolidApollo.com
page 2
™
The channel diuser can easily be installed in one of two ways (see illustration below) :
A: Slide the diuser onto to the nothes of the channel.
B: Align the diuser to the starting edge of the channel and slightly push down on it until you hear or feel it snap in to place. Once it is
snapped into place, continue to press down onto to the rest of the diuser until you reach the end of the channel.
Step 3: Install Channel Diusers
A B
Slide the Diuser
onto the channel.
Align the diuser onto the starting
edge of the channel and carefully
push down on the diuser until you
feel it snap into place.
The Decorative cover can easily be installed in the same fashion as
the Diuser:
Simply align the Decorative cover into the top and botom nothes of
the crown molding and then slide it until you reach the end.
Another method is by placing the Decorative cover at the top notch
rst then slightly push down on the bottom until you hear or feel it
snap in to place.
Apply the same method to the rest of the Decorative cover until you
reach the end of the crown molding.
Step 4: Install Decorative Cover
Decorative Cover
Crown Molding
PRODUCT MANUAL
78” Crown Molding LED Strip Channel
Installation Guide
Contact Us: 425.582.7533
www.SolidApollo.com
Andrew@SolidApollo.com
page 3
™
Installing the Channel Raceway Base to the corner wall.
Installation Guide - When Encountering a Corner
The installation for corners involves a miter cut to the Decorative Cover. Please do not cut the channel. Follow the instructions step by step to
properly install the product.
A. Before installing the Channel Raceway Base to the corner wall, please keep in mind that it is very important that you leave 1.5 inches of
gap between the corner wall and the Channel.The 1.5 inches of gap will ensure the LED strip lights to go around corners without tension
on the LED strip or cables (see illustration Cbelow). Apply the same rule onto the other corner.
B. Once the Channel Raceway is installed, in order for the corners to have a seamless look, the Decorative cover is going to require a miter
cut (45 degree angles).This is done by an angled saw or a miter box. See illustration Dbelow for a miter cut example. When you have
done it correctly, the nished product should look like the illustration shown in letter E.
1.5in
LED Strip LED Strip
1.5in
Leave 1.5in gap on either side of
corner base sections.
C D
E
Decorative Cover - Top view
Decorative Cover
Crown Molding Crown Molding
Otros manuales de Equipo de iluminación de Solid Apollo
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
