Softrend Chatbox Manual de usuario
CHATBOX by SOFTREND
Assembly
Manual
sorend.ee
sorend.eesorend.ee
A
Ax1
Hx1
Dx1
Kx1
Ex2G1 x2
Fx2
G2 x2
Lx1
Jx1
Rx1
Px3
Bx1
Gx1
Cx1
Mx2 Nx2
E
E
FF
B
C
G
H
J
K
LM
N
P
P
P
R
G1
G1
G2
G2
D
M
N
2106mm
1096mm
1140mm
894mm
1
sorend.ee
x1
f
x1
e
3,5x35mm
T15
T25
T15
d
4,5x50mm
c
x4
x4
x8
x4
M10
5x60mm
a
b
2
Sucon cups
min. 2x120mm 2pcs Level 1pcs Scissors 1pcs
Stepladder 1pcs
Ulity knife 1pcs
Crowbar 1pcs Plasc Block 1pcs
TOOLS:
Wrench 10mm 1pcs
Cordless drill with
drill bits set
x1 x1
x1
x8
g
k
h
m
min
2350mm
NB!
Rubber mallet 1pcs
Screwdriver 1pcs
Vacuum cleaner 1pcs
5
Ratcheng wrench with
long 5mm Allen key
Cleaning supplies 1set
300L extrastong trash-
bags 5pcs
Allen key
2-10mm 1set
sorend.ee
3
A
2.
2.
3.
3.
B
A
1.
1.
1.
1.
2.
2.
1.
3.
3.
C
sorend.ee
x4
M10
a
4
1. Remove carpet plugs on marked posions and use
a long 5mm allen key to adjust 4 levelling glides in the
corners to avoid the floor module from shiing during
assembly.
Note! Glides must be lowered minimally.
85
85
120
120
510
1.
A
85
85
540
120
120
A
A
5mm
2.
A
B
3.
AB
10mm
a
2. Insert the posioning rods aached to side modules
(B and C) into the floor module posioning holes.
3. Secure side modules to the floor
module using part “a” and ghten it
with 10mm wrench.
Note! Make sure there is no gap between
the side and floor module beams.
sorend.ee
E
F
5.
6.
4.
4.
B
D
E
F
5.
4.
4.
C
5
4.
6.
B
D
B5.
F
E
b
4. Aach assembly support beams (E)
to the side modules.
5. Place safety support beams (F) on top
of the assembly support beams (E).
6. Li ceiling module (D) on top of the side
modules (B and C) and secure the ceiling
module by lowering it between the side modules
unl connectors are even to each other.
T25
x4
5x60mm
b
sorend.ee
6
8.
7.
8.
7.
FF
E
E
LB
B
L
7. Remove support beams (E) and (F) aer
ceiling module is aached.
8. Connect the electrical fings between side module (B)
and table (L), then place table on top of the pre-installed
laths on side module.
sorend.ee
7
9.1 Click in profile (G2) to the ceiling module using a rubber mallet
and plasc block to secure it.
9. Back-glass panel installaon:
9.2 Place the back-glass panel (G) into the aluminum profiles:
Step 1. Li the glass panel (G) into the top aluminum
profile using sucon cups,
Step 2. Push the boom of the glass panel (G) towards
the front of the cabin,
Step 3. Carefully lower the glass panel (G) unl it
stands on spacers pre-installed into boom
aluminum profile.
1.
2.
D
G
A
3.
9.1
D
A
9.
B
G
C
D
G2
9.2
G2
G2
G1 G1
sorend.ee
9.3
9.3
G2
9.5
A
9.3
B
C
NB!
FRONT
9.4
G2
G2
G1G1
G
x1
e
G
9.3 Secure the back-glass panel by wedging two shims “e” between
the glass panel (G) and the wooden spacer making sure they
are ght.
Carefully shi the glass panel with a plasc crowbar to create
clearance for the shims “e”.
9.4 Click in profile (G1) to the side modules using a rubber mallet
and plasc block to secure it.
9.5 Click in profile (G2) to the floor module using a rubber mallet
and plasc block to secure it.
Note! Shims “e” must be cut into fing size first.
9.3 BACK
C
G
e
Note! Slide the vercal profile (G1) up between the top profile and
side module.
8
sorend.ee
H
10.1
f
f
f
Hff
f
NB!
10.2
9
H
H
H
NB!
10. x1
f
10. Door frame installaon:
10.1 Aach expanding tape “f” to the sides
and top of the door frame (H).
10.2 Posion the door frame (H) in the front
opening and shi it evenly between side
modules.
Note! Expanding tape must be cut in the corners,
not curved around the corners.
Note! Make sure the front face of the door
frame(H) is in line with the front face
of the side modules.
