Sofi SP8 Series Manual de usuario
Sofei Technology
SP8serial programmer
manual
Shenzhen Shuofei Technology Co., Ltd.
SOFI TECHNOLOGY CO.,LTD.
TEL: 0755 - 8486 7757
FAX: 0755 - 8486 7941
WEB:http://www.sofi-tech.com/
Publication Release Date: 2018-07
Revision B4
Description: This manual applies toFlyPROsoftwareV4.40or above
Before using the programmer, please read this manual carefully, and operate the programmer correctly as required. Failure to operate the programmer as required will result in damage to the
programmer and no warranty service!
Translated from Chinese (Simplified) to English - www.onlinedoctranslator.com
Sofei Technology manual
SP8 series programmer
target record
Chapter One product description-------------------------------------------------- -------------------------------------------------- ---------------------
Features------------------------------------------------ -------------------------------------------------- ----------------------- SP8Series
function comparison table --------------------------------------------- -------------------------------------------------- --------
programmer hardware-------------------------------------------------- -------------------------------------------------- ------------------5
quick to use-------------------------------------------------- -------------------------------------------------- ---------------------7 Offline
burning-------------------------------------------------- -------------------------------------------------- ---------------------11 Download
offline data -------------------------------------------------------- -------------------------------------------------- ------------------11 Run
Offline - Manual Mode-------------------------------------------- -------------------------------------------------- --------12 Offline
operation - automatic control mode --------------------------------------- -------------------------------------------------- ---12
Offline working mode status indicator --------------------------------------- -------------------------------------------------- -----12
Offline Data View---------------------------------------------- -------------------------------------------------- -------------------13 ISP
Mode burning-------------------------------------------------- -------------------------------------------------- -------------14 ISPs
interface------------------------------------------------- -------------------------------------------------- ---------------------14 ISPs
Connection line ------------------------------------------------ -------------------------------------------------- -------------------14 Target
chip connection--------------------------------------------------------- -------------------------------------------------- ---------------- ISP
Power Mode------------------------------------------------ -------------------------------------------------- --------------- common
problem--------------------------------------------------- -------------------------------------------------- --------------------17 Disclaimer
-------------------------------------------------- -------------------------------------------------- ---------------------19 file revision log
information-------------------------------------------------- -------------------------------------------------- --------20
3
3
4
Chapter two
third chapter
Chapter Four
chapter Five
15
16
Appendix I
Appendix II
Appendix III
Shenzhen Shuofei Technology Co., Ltd.2
Sofei Technology manual
SP8 series programmer
Chapter 1 Product Introduction
Features
⚫USBPower supply and communication without external power supply. Small size, easy to carry.
⚫Specifically designed for serial memory, it is faster and more stable than general-purpose programmers.
⚫support93/24/25Series memory, support software upgrade to add support for new chips.
⚫Supports poor pin contact detection, effectively improving programming reliability.
⚫standard40Foot zero insertion force locking seat, wide and narrow chips and universal adapters can be used.
⚫The overcurrent protection function can effectively prevent the impact of chip placement errors or bad chips on the programmer.
⚫supportISPMode programming, for the onboard SMD chip, it can be directly wired and programmed.
⚫The programmer has a built-in high-speed processor, which provides high-speed programming and precise timing.
⚫Can be run offline(Note1), without connecting to a computer. built-in128Mbitdata storage.
⚫Mass production programming mode, which automatically detects chip placement and starts programming operations.
⚫support25seriesSPI FLASHChip model detection.
⚫Buzzer sound indicates success or failure.
⚫Support low voltage (3.3V)and5Vchip.
⚫Provides device self-check function.
⚫supportWinXP(SP2),VISTA, Win7, Win8, Win10(32bit/64bit).
Note1: ISPMode does not support offline burning
Shenzhen Shuofei Technology Co., Ltd.3
Sofei Technology manual
SP8 series programmer
SP8Series function comparison table
Product number:SP8-FX SP8-F SP8-B SP8-A
Support chip maximum capacity(Note1)512Mb(online)/128Mb(offline)512Mb
Support chip voltage 3.3V/5V
Offline burning Y Y N N
Built-in memory (save offline data)128Mb -
Online mass production Y(Automatic detection of chip placement/removal)N
automatic serial number Y(Online burning mode only)N
Buzzer prompt Y(offline mode only)N N
Overcurrent/Short Circuit Protection Y
Lock seat type Domestic gold-plated
ISPburn(Note2)part93/25Series (clock not adjustable)
OTParea read and write(Note2)support not support
Chip configuration(Note2)support not support
Automatic burning machine support (ATE)YN N N
GD25Q16(SOP8) P+V=7.9S
Burning speed
(Note3)
W25Q128FV(SOP8) P+V=60S
MX25L12845E(SOP16) P+V=130S
Offline data download speed 216S@128Mb -
Number of supported chips(Note4)7874 7804 6401
Note 1: SP8Series offline operations support up to128Mbit.
Note 2:Depending on software capabilities, not all chips are supported.
Note 3:The burning speed adopts100%random numbers for testing,Pfor programming,VFor verification; Offline time only applies to products that support the Offline function;
The burning time is for reference only.
Note 4:Number of chips based on software versionV4.06(2016-03-12),Chips will be continuously upgraded, and the numbers in the table are for reference only.
Shenzhen Shuofei Technology Co., Ltd.4
Sofei Technology manual
SP8 series programmer
Chapter 2 Programmer Hardware
Lock seat
Power Indicator (PWR)
Status Indicator (STA)
USB interface
ISP/ATE interface
⚫Lock seat
Used to place chips (including chip adapters/adapters).
Please do not operate the chip that has been soldered on the circuit board through the connection method on the locking seat. The peripheral circuit on the board will cause the operation to fail, and the
programmer will be damaged in severe cases.
Typical Chip Placement Diagram
Pin 1
The placement of other chips (including adapter information) can be found inFlyPROOpen the chip information in the software for viewing.
The locking seat is only used to place the chip to be programmed (including the adapter/programming seat), and it is forbidden to operate the chip that has been soldered on the circuit board through the
connection method. This may cause permanent damage to the programmer.
Shenzhen Shuofei Technology Co., Ltd.5
Sofei Technology manual
SP8 series programmer
⚫Power Indicator(PWR)
Indicates the power supply status, and the red light indicates that the power supply is normal (SP8The programmer directly usesUSBinterface power supply); red flashing indicates that the programmer has
detected a short circuit of the chip or excessive current.
⚫Status Indicator(STA)
Programmer Status Indicator Description (Online Mode):
STAlight status Status Description
orange chip is being burned
green The chip burning is completed, the burning is successful
red Chip burning failed
Offline programming mode status indicator description (onlySP8-F, SP8-FX):
STAlight status Status Description
flashing green Waiting for chip placement
orange chip is being burned
green The chip programming is completed, the programming is successful, waiting for the chip to be removed
red Chip programming failed, waiting for the chip to be removed
⚫ISP/ATEmulti-function interface
ISPFunction: In the software, select theISP] suffix of the chip model, the programmer will useISPway to burn the chip. This interface is used to connect the target board
(chip). For specific connection diagrams, please refer toChip informationView in
ATEFunction: existSP8-FXIn the product, this interface can be used to connect the automatic control machine (automatic burning machine), the interface
providesSTARTstart signal, andOK / NG / BUSYindication signal.
Note: This interface is a multiplexed function interface and can only work onISPorATEone of the modes.
⚫USBinterface
In online operation mode, theUSBinterface to communicate and supply power to the programmer at the same time. In
offline operation mode, it is used to connect a dedicated power adapter (onlySP8-F,SP8-FX).
Shenzhen Shuofei Technology Co., Ltd.6
Sofei Technology manual
SP8 series programmer
Chapter 3 Quick Use
This chapter explains ShuofeiSP8series programmerFlyPROThe basic operation steps are suitable for users who use this programmer for the first
time. Corresponding product model:SP8-A, SP8-B, SP8-F, SP8-FX.
1.useUSBConnect the programmer to the computer. turn onFlyPROsoftware. After the software is started,
the programmer hardware will be automatically connected.
Information about the programmer will be displayed in the main window of the software. As shown below:
At the same time, the connection status of the programmer will be displayed in the status bar at the bottom of the software. As shown below:
If the programmer is not inserted before when the software starts, the software will pop up the programmer selection dialog. As shown below:
In this case, please use the programmerUSBcable to connect to computerUSBinterface.
Select the correct programmer model, click "Connect (C)"That's it.
2.Select the chip model to be programmed.
Click the toolbar button
chip model.
, or the menu【Chip】-【Choose Chip Model】to open the "Choose Chip" dialog box, select the chip to be programmed
3.Query chip related information
Click the toolbar button
and how/where the chip is placed in the locking seat.
, or the menu [Chip] - [Chip Information] to open the chip information description to understand the relevant programming instructions of the chip
Shenzhen Shuofei Technology Co., Ltd.7
Sofei Technology manual
SP8 series programmer
4.Load the burn file
Click the toolbar button , or the menu【File】-【Load File】to carry out the data file to be burned.
5.Set Action Options
Click the toolbar button
In most cases, you can use the default settings without additional settings. For details on operation options, please refer to the software manual.
, or the menu【Operation】-【Operation Options】to set the chip programming.
6.Place the chip in the lock seat
Non-in-line chips need to use adapter sockets (adapter sockets).
The placement position and direction of the chip, please click the toolbar button to view.
7.Execute burn
The burning operation can adopt three modes, including manual mode, automatic mode, and automatic mass production mode. Select one of the modes to operate according to different
situations.
⚫manual mode
In the command bar on the left side of the main window of the software, select the "Manual Operation" page, as shown in the figure below:
button
Except: clear chip content, only forFlashclass of chips
EEPROMThe chip of this class does not have this function, this button will be disabled
(gray) Check whether the content of the chip is blank (all areFFh)
Write buffer data to the chip.
Need to preload the data file into the buffer
Compare the data in the chip with the data in the buffer (verify whether the data in the chip is
correct)
Function
wipe
check
edit
null:
Procedure:
school Test:
Write configuration:Write configuration information into the chip (egSPI FLASHof
Status Register);
Fetch: read the chip content, the read data will be saved in the software buffer, such asread
Save as a file if necessary (toolbar button: Save).
Read the configuration information of the chip, and the read configuration data will be updated to the configuration
option settings of the software. After doing this, hit the configurable option to view the current chip into the
configuration state.
Read configuration:
Typical operating steps:
➢burnSPI FLASH (25series): erase→check empty→programming→check
➢burnSPI FLASH (25series, brand new blank chip) : programming→check
➢burnI2C EEPROM (24series): programming→check
➢Read chip data and save chip data to file: read→check→save
Shenzhen Shuofei Technology Co., Ltd.8
Sofei Technology manual
SP8 series programmer
⚫automatic mode
In the command bar on the left side of the main window of the software, select the "automatic operation" page, the automatic operation page has2There are two types, namely simple setting and advanced setting,
which are determined according to different product types.
The operation sequence of the simple setting is fixed, and whether the setting operation is valid depends on whether the
check is enabled. Advanced settings can set any operation content, and the order can also be adjusted at will.
After setting the operation content, click the "Auto Run" button, and the programmer will execute the "operation content" in turn.
Easy Setup
Applicable Model:SP8-A, SP8-B
advanced settings
Applicable Model:SP8-F, SP8-FX
⚫mass production mode
The operation content of mass production mode is the same as "automatic operation", the difference is that the programmer can automatically detect the placement and removal of chips. After clicking the "Burn in mass
production" button, the software pops up a message box to remind the user to place the chip. After the chip is placed, the programming operation will be performed automatically, and the user will be reminded to
remove the chip after the programming is completed. When the user removes the chip, it will continue to wait for the placement of the next chip, and the software keeps repeating this operation until the user clicks "
STOP”button to stop operation.
Wait for the chip placement prompt
Shenzhen Shuofei Technology Co., Ltd.9
Sofei Technology manual
SP8 series programmer
Wait for the chip to be removed
illustrate
⚫Production mode is only available forSP8-B / SP8-F / SP8-FX.SP8-AThe mass production burning function is not supported.
⚫The above operations are just to demonstrate the conventional programming method of general chips, for reference only. The specific operation needs to be determined according to the user's needs.
⚫For more information about the software, please refer toFlyPROSoftware online help.
Shenzhen Shuofei Technology Co., Ltd.10
Otros manuales para SP8 Series
1
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Placa madre de Sofi
Manuales populares de Placa madre de otras marcas
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manual de usuario
Gigabyte
Gigabyte GA-9IVDT Manual de usuario
Texas Instruments
Texas Instruments ADS8372EVM Manual de usuario
Commell
Commell MS-C73 Manual de usuario
IBT Technologies
IBT Technologies MB860 Manual de usuario
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manual de usuario
