Socket & See MFT5000 Manual de usuario

2 YEAR

MFT5000

multifunction installation tester

Optional

personalised

splash screen

Instruction Manual & Speciﬁcation

SAS014v1

Introduction

The Socket and See MFT5000 Multifunction Installation Tester has been designed and

built to the highest standards providing you with a safe and simple solution to your test

requirements.

The MFT5000 tester is used to verify the safety of Commercial, Domestic and

Industrial installations. All testing is required to meet BS7671. The MFT5000 covers all

aspects of these requirements with ease of use and safety in mind.

Conformance with Standards

This tester complies with all the latest UK and European regulations.

This tester has been tested according to the following regulations:

BS EN 61010-2-030:2010 - Safety requirements for electrical equipment for

measurement, control and laboratory use. Particular requirements for testing

and measuring circuits.

BS EN 61326-2-2:2013 - Electrical equipment for measurement, control and

laboratory use. Particular requirements for portable test, measuring and

monitoring equipment used in low-voltage distribution systems.

BS EN 61557:2007 - Electrical safety in low voltage distribution systems up to

1000V AC. and 1500V DC. Equipment for testing, measuring or monitoring of

protective measures.

• Part 1 : General Requirements

• Part 2: Insulation Requirements

• Part 3: Loop Requirements

• Part 4: Continuity Requirements

• Part 6: RCD Requirements

• Part 7: Phase Rotation Requirements

• Part 10: Multifunction Requirements

Marking Explanations

Warning! Refer to manual.

Caution! Voltage present. Risk of Electric Shock.

Earth

Double Insulation

This instrument should be recycled as electronic waste.

User accessible fuse in battery compartment - F0.5A, 500V, HRC 6.3 x 32mm

Prohibited to use for the Electrical System which uses the voltage above 550V.

Conformity to European Standards

CAT III/CAT IV

CAT III Testers are designed to protect against transients and fault

currents in ﬁxed equipment installations at the distribution level. Exam

ples are measurements on distribution boards and socket wiring.

CAT IV Testers are designed to protect against transients and fault currents

from the primary supply level (overhead or underground utility service).

Examples are measurements made before the main fuse or circuit breaker.

Warnings

Read Before Using

• To maintain operator safety use only speciﬁed accessories.

• When working on live circuits, use of a proving unit such as the

Socket & See SP400 is recommended to establish correct function

of the tester.

• If the equipment is used in a manner not speciﬁed by the

manufacturer, the protection by the equipment may be impaired.

• Disconnect from external circuits before removing battery cover.

• Inspect the tester and accessories for damage before use and do

not use if damage is found.

!>550 V

Safety

See page 2 for a list of symbols used on the product and in this manual.

A Warning identiﬁes hazardous conditions and actions that could cause bodily harm or

death.

A Caution identiﬁes conditions and actions that could damage the instrument or cause

permanent loss of data.

Warnings: Read Before Using

To prevent possible electrical shock, ﬁre, or personal injury:

• Use the product only as speciﬁed, or the protection supplied by

the product can be compromised.

• Do not use the product around explosive gas, vapour or in damp or

wet environments.

• Do not use test leads if they are damaged. Examine the test leads

for damaged insulation, exposed metal, or if the wear indicator

shows. Check test lead continuity.

• Use only approved accessories such as test leads etc supplied with

the instrument. Part numbers of replacement leads on pg 4

• Do not use the product if it is damaged.

• To be repaired by Socket & See authorised agents only.

• Do not apply more than the rated voltage between the terminals or

between each terminal and earth ground.

• Remove test leads from the tester before battery cover is removed.

• Do not operate the product with covers removed or the case open.

Hazardous voltage exposure is possible.

• Use only speciﬁed replacement fuse. Fuse type F0.5A, 500V, HRC

6.3 x 32mm

• Keep ﬁngers behind the ﬁnger guards on the probes at all times.

• Connect the common test lead before the live test lead and

remove the live test lead before the common test lead.

• Use Personal Protective Equipment (approved rubber gloves, face

protection, and ﬂame-resistant clothes) to prevent shock and arc

blast injury where hazardous live conductors are exposed.

Unpacking the Tester

Your Socket & See Multifunction Tester comes complete with:

Description Part No Qty

Multifunction Tester Socket & See MFT5000 1

Instruction Manual 1

3 Wire Split Lead Socket & See DLM PRO LEAD 1

Assembly with Probes +

Crocodile Clips Brown/Blue/Green

13 Amp Mains Lead to 4mm Socket & See PRO LEAD 1

Connections Brown/Blue/Green

Remote Switch Probe Socket & See RSP 1

AA LR6 Alkaline Battery 6

Heavy Duty Carry Case Socket & See MFT CASE 1

Neck Strap Socket & See MFT STRAP 1

Certiﬁcate of Calibration 1

Warranty Registration Card (terms of 3 year warranty on pg 34)

All the parts listed above are included in the carry case.

Operating the Socket & See MFT5000

To insert batteries ensure the instrument is switched o and no test leads are connected.

Remove battery cover from base of unit, insert batteries into holder ensuring correct

polarity.

Replace cover.

Always use good quality LR6 AA Alkaline Batteries.

Re-chargeable batteries are not suitable.

Battery power level indicated on the colour display by the symbol.

Please dispose of your batteries carefully.

Batteries are made from important resources and chemicals, including lead, cadmium,

zinc, lithium and mercury. If batteries are disposed of as normal waste, they'll be taken to

a landﬁll site and those resources will be lost and will contribute to the pollution of the

environment. Recycling is one way you can help the environment and you should dispose

of used batteries separately from other waste, using local collection

and recycling schemes available.

100%

75%

50%

25%

Overview

Front panel and controls

Top View

Operating the Socket & See MFT5000

All Test Functions are selected by using the main rotary switch.

1. Power o

2. Socket/Polarity Test

3. No Trip Earth Loop Impedance Test

4. High Current Earth Loop Impedance Test

5. 30mA Auto Sequence Type G RCD Test

6. 30mA RCD Test (Manual) Type AC/A

7. 100mA RCD Test (Manual) Type AC/A

8. 300mA RCD Test (Manual) Type AC/A

9. 500mA RCD Test (Manual) Type AC/A

10. 100mA RCD Test (Manual) Type ACS/AS

11. 300mA RCD Test (Manual) Type ACS/AS

12. Phase Rotation Test

13. 1000V Insulation/Resistance Test

14. 500V Insulation/Resistance Test

15. 250V Insulation/Resistance Test

16. Continuity Test

Operating the Socket & See MFT5000

Push Buttons

1. Test Button - Initiates all selected tests

2. Handsfree - Handsfree function for Continuity, Insulation & Loop

3. PFC/Loop/RCD Recall - Prospective fault current value after Loop Test Result

lists the last set of RCD Test Data from an Auto Test

4. RCD Multiplier - Toggles RCD Multiplier value

5. RCD AC/A/Continuity Null - Nulls the Resistance Value from the Test Leads in use /

Toggles between type A/AC RCD

6. Polarity Test Pad - Unique safety function ensuring correct mains polarity

Auto power o function

To ensure long battery life the MFT5000 will automatically power o when standing idle for

3 minutes. To power the MFT5000 either return the selector switch to “OFF” and then back

to the test selection or simply press any of the four buttons under the display screen.

2 3 4 5

BROWN vΩ

CIRCUIT

RESISTANCE

GREEN (COM)METER

RESISTANCE

BATTERY v

Test and Measurement Functions

Continuity

Caution

Principal of Measurement.

During continuity measurement current ﬂows from battery positive through the Brown

(VΩ) lead, external circuit resistance, Green (COM) lead, meter resistance and ﬁnally

back to the battery negative.

The current and voltage are measured as shown and the external resistance calculated.

When the leads have previously been nulled, their resistance is subtracted before

displaying the reading.

The purpose of Continuity Testing is to establish the resistance of the circuit under test.

Test Procedure

Insert the brown test lead into the brown input terminal & the blue test lead into the

green terminal.

The brown test lead can be substituted by using the red remote test probe supplied.

This allows remote activation of the MFT5000 from the safety of the test probe ensur-

ing that you are always looking at the point of contact and not the MFT5000.

1. Test Button - Initiates all selected tests

2. Handsfree - Handsfree function for Continuity, Insulation & Loop

3. PFC/Loop/RCD Recall - Prospective fault current value after Loop Test Result

lists the last set of RCD Test Data from an Auto Test

4. RCD Multiplier - Toggles RCD Multiplier value

5. RCD AC/A/Continuity Null - Nulls the Resistance Value from the Test Leads in use /

Toggles between type A/AC RCD

6. Polarity Test Pad - Unique safety function ensuring correct mains polarity

Auto power o function

To ensure long battery life the MFT5000 will automatically power o when standing idle for

3 minutes. To power the MFT5000 either return the selector switch to “OFF” and then back

to the test selection or simply press any of the four buttons under the display screen.

Tabla de contenidos

Otros manuales de Equipo de prueba de Socket & See

Socket & See

Socket & See SP200 Manual de usuario

Socket & See

Socket & See PDRC 380 Manual de usuario

Socket & See

Socket & See PDIT 360 Manual de usuario

Socket & See

Socket & See PDL 234Plus Manual de usuario

Socket & See

Socket & See CB400 Manual de usuario

Socket & See

Socket & See VVD PRO Manual de usuario

Socket & See

Socket & See RCD PRO Manual de usuario

Socket & See

Socket & See VIP 100 Manual de usuario

Socket & See

Socket & See PDL 310 Manual de usuario

Socket & See

Socket & See SP 200 Manual de usuario

Socket & See

Socket & See VIP ESI Manual de usuario

Socket & See

Socket & See FFCB 100 Manual de usuario

Socket & See

Socket & See DRC430 Manual de usuario

Socket & See

Socket & See DLM PRO Manual de usuario

Socket & See

Socket & See PDL PRO Manual de usuario

Socket & See

Socket & See DIT 400 Manual de usuario

Manuales populares de Equipo de prueba de otras marcas

SMART

SMART KANAAD SBT XTREME 3G Series Manual de usuario

Agilent Technologies

Agilent Technologies BERT Serial Manual de usuario

Agilent Technologies

Agilent Technologies N3280A Manual de usuario

Vernier

Vernier Go Direct Voltage Manual de usuario

Lifeloc

Lifeloc R.A.D.A.R. Manual de usuario

Fluke

Fluke T5-600 Instrucciones de funcionamiento e instalación

Mercury

Mercury TSL01 Manual de usuario

MAHA

MAHA MBT Series Manual de usuario

Fuji Electric

Fuji Electric P-61 Manual de usuario

ETC

ETC SealerAtor Manual de usuario

Skyfine

Skyfine ETHYWAY V2 Manual de usuario

Appion

Appion G5 Twin Manual de usuario

PCB Piezotronics

PCB Piezotronics 8159-0112A Manual de usuario

BW Technologies

BW Technologies MicroDock II Manual de usuario

Sun Nuclear

Sun Nuclear 1027 Manual de usuario

Biomark

Biomark HPR LITE READER Manual de usuario

Hioki

Hioki 3169-20 Manual de usuario

Ashcroft

Ashcroft ATE-100 Manual de usuario