Sno-Pro Fast-Cast 550 series Manual de usuario

™

Fast-Cast 1CS6E - Aluminum Hopper with Stainless Steel Body & Electric Motor

Fast-Cast 1CS6H - Aluminum Hopper with Stainless Steel Body & Gas Motor

Fast-Cast 1CS6CPH - Poly Hopper with Carbon Steel Body & Gas Motor

1 of 18

FAST-CAST 550 SERIES SPREADERS

Curtis Industries Inc. LLC, 111 Higgins St., Worcester, MA 01606 TEL: (800) 343-7676 FAX: (508) 854-3377 For Parts and information visit us at www.Curtisindustries.net

Curtis Industries Inc. LLC, reserves the right to change product design or specifications without notice or liability.

Assembly and Owner's Manual - January 2011

1CS6E

Electric Spreader

Revised 7 February 2011

2 of 18

 ►DonotattempttooperatethisSpreaderuntilyouhavereadandunderstandallwarningsandinstructions

 intheOwner’smanualandonSpreaderunit.Failure to read and follow all warnings and instructions

may lead to serious injuries or death.

 ►Foryoursafety,warningandinformationdecalshavebeenafxedtothisproducttoremindall

 operatorsofsafetyprecautions.Ifdecalsaremarked,damagedordestroyed,replacewithnewdecals

 orderedfromCurtisIndustries,LLC.

IMPORTANT: Before you Start...

1. Most accidents are preventable and caused by human error.

Exercise care and precautions to prevent the possibility of injury to operator or to others.

2. Before working with the Spreader, secure all loose tting clothing and unrestrained hair.

3. Always wear safety glasses with side shields when working metal against metal. Failure to do

so could result in serious injury to the eyes.

4. Never allow children to operate or climb on equipment.

5. Never attempt to adjust or service Spreader while engine is running.

6. Never attempt to un-jam Conveyor Chain while engine is running.

7. Do not stand behind Material Chute while Spreader is discharging.

8. Do not refuel a hot engine. Allow time to cool before refueling.

9. Never weld or grind on equipment without having a re extinguisher available.

10. Always inspect unit for defects: Broken, worn or bent parts, weakened areas on Spreader or

Mount.

11. Always shut off vehicle and power source before attempting to attach or detach or service

Spreader unit. Be sure vehicle/power source is properly braked or chocked.

12. Always make sure personnel are clear of areas of danger when using equipment.

13. Always keep hands, feet, and clothing away from power-driven parts.

14. Remember, it is the owner’s responsibility to communicate information on safe usage and

proper maintenance of all equipment.

■ NEVER enter Hopper Box while Conveyor Chain is moving.

■ DO NOT RIDE on any part of the Spreader while vehicle is in motion.

■ Disconnect & lock out Power source before adjusting or servicing.

DANGER

WARNING

MOVING PART HAZARD

TO AVOID INJURY

3 of 18

IMPORTANT

■ Always check areas to be spread to be sure no hazardous conditions or substances are in the

area.

■ Never operate equipment when under the inuence of alcohol, drugs or medication that might

alter your judgement and / or reaction time.

■ Do not overll Spreader. (See decal on Spreader for ll capacities)

■ Failure to keep Conveyor Chain Links lubricated and free running can damage the Conveyor Chain,

Drive Shafts and body structure.

■ Failure to maintain Conveyor Chain or other components can void warranty.

Complete this Check List Prior to Initial Start-Up & Operation

Read and understand Curtis Owner’s & Operator’s Manual.

Read and understand Engine Manual.

Read and understand ALL Warning Decals.

Check Fuel Level.

Check Engine Oil Level.

Grease all Lubrication Points.

Oil Conveyor Chain.

Wire In-Cab Control Panel.

Coat Harness Connector Ends with Dielectric Grease.

Verify Spreader is secure in Vehicle using provided Ratchet Straps.

For Utility Vehicle applications (i.e. JD Gator, Kawasaki Mule, etc.)

Dump Body Safety Chain must be attached to secure Dump

Body & Prevent accidental release of Dump Body.

For Pickup Truck Applications make sure locking Bolts are in place

before moving vehicle.

General Maintenance Requirements

1. Wash Unit thoroughly after each use.

2. Lubricate Bearings

3. Periodically Lubricate Conveyor Chain with new or used Engine Oil.

4. Check Engine Oil every 5 hours or daily before use.

5. Change Engine Oil every 50 hours of Operation or every season.

6. Service Engine Air Filter every 100 Hours of Operation or every season.

When choosing a location

for the Control Panel, do not

position the Panel in line with

the Driver’s or Passenger’s seat

to ensure the Control Panel is

not hit accidentally.

1D. Body Safety Chain Installation

For UTV applications: A Dump

Body Safety Chain must be

attached to secure the Dump

Body and prevent the accidental

release of the Dump Body.

InstallEyeboltstoVehicleFrameandDumpBodyof

theUtilityVehicle.Usinga32"ChainandaOneLink

Connector,attachChaintotheEyeboltsmountedto

theFrameandDumpBody.SafetyChainsaretobe

usedinconjunctionwiththeHoldDownAssemblies.

AttachingaChainwillpreventanaccidentalrelease

oftheDumpBody.TheChain/Eyeboltsetupisnot

requiredforPickuptruckapplications.

Section 1. Installation Instructions

1A.TheFast-Cast550Spreaderisdesignedformounting

inthebedofmostUtilityVehicles.FourHold-Down

AssembliesareprovidedforsecuringtheSpreaderto

theVehicle.

For Pickup Truck Installation

See page 15.

1B.RemovetheTailgatecompletelyfromtheVehicleif

possible.CentertheSpreaderinthebedoftheUTV

andshifttheSpreaderasfarforwardaspossible,

butleavingenoughclearancefortheMaterialChute

installationattherear.UsingfourHoldDown

Assemblies,securetheSpreadertotheVehicle.

1C.In-Cab Control Panel Installation

ConnecttheWireTerminalEndoftheHarnessCable

totheControlPanel.Whenconnectingwires,besure

theignitionswitchisinthe'OFF'position.Mountthe

ControlPaneltotheundersideofthedashboard,

makingsuretheControlPanelisgroundedtothe

Vehicle.

Figure 1. Fast-Cast 550 Spreader Overview (UTV mounted)

Hopper Assembly

Conveyor Assembly

Engine Assembly

Discharge

Assembly

Hold-Down Assemblies

(2 per Side)

Hopper

Gate

IMPORTANT

4 of 18

Sno-Pro Fast-Cast 550 Spreader

CAUTION

NOTE

5 of 18

Sno-Pro Fast-Cast 550 Spreader

1D. (continued)

Failure to attach this Chain

may result in an accidental

Body Dump, damaging the

Spreader, the Utility Vehicle,

persons seated in the Vehicle,

or standing nearby.

Section 2. Operating Instructions

2A. Engine Starting and Cab Controls (Gas Motors)

Step 1.Verifythatthe'ON/OFF'Switchisinthe

 'ON/RUN'positionontheCabControlPanel.

Step 2.GotoEngineattherearofSpreader.

MovetheThrottleControltothe'FAST'

Position.

 PushPrimerBulbrmly3-5times.

 GraspRopeHandleandpullcordrapidly

tostartEngine.

(SeeEnginemanualfordetails.)

Step 3.FromtheCabControlPanel,ipthe

ConveyorSwitchtothe'ON'position.

ThiswillengagetheConveyorChainand

SpinnerDisc.

Figure 3. 1CS6E-C Electric Spreader Cab Control

2B. Electric Spreader and Cab Controls

Step 1.Verifythatthe'ON/OFF'Switchisinthe

 'ON'positionontheCabControlPanel.

 ThiswillengagetheConveyorChainand

SpinnerDisc.TheGreenIndicatorLightwill

 comeon.

Step 2.SpinSpeedControllertodesiredspeedsetting.

Step 3.Anadditionalamountofmaterialcanbe

spreadinspotsbytogglingthe'BLAST'Switch.

 TheSwitchcanalsobeheldonforincreased

 dispersalwhenneeded.

 TheYellowindicatorlightilluminateswhenever

 the'ON'switchistoggledtoindicatea3-Spin

 Burstspinisoccuringtoclearthe

 Spinner/ConveyorSystemontheSpreader.

 TheSpreaderwillthenoperateatthespeed

 settingonthedial.

 TheRedIndicatorLightilluminateswhenthe

 isoverloaded.StoptheSpreaderfunctionsand

 checktheSpreaderformaterialproblemsinthe

 Spinner/ConveyorandtheGateareawhereit

 feedsfromtheHopperbeforeresuming.

2C. Gate Height Adjustment Steps

Step 1. LoosentwoGateScrews.

Step 2.AdjustGatetodesiredheight.

Step 3.TightenGateScrews.

WARNING

2D. Material Chute Deectors

AdjusttheMaterialDeectorstonetunethe

spreadpattern.KeepallMaterialDeectorsatthe

sameangle.

Foralargerspreadpattern:RaiseDeectors.

Forasmallerspreadpattern:LowerDeectors.

Never attempt to adjust

Material Deectors while

Spreader is operating.

2E. Conveyor Chain Adjustment

TightenbothTake-UpBoltsequallyuntilslackis

goneintheConveyorChain.

After adjusting the Conveyor

Chain, verify that the Take-Up

Shaft is not at an angle.

Never attempt to adjust

Conveyor Chain while Spreader

Engine is running.

2F. Fast-Cast 550 Spreader Storage

1.)WashUnitThoroughly

2.)OilConveyorChain

3.)LubricateAllBearings

2G. Fast-Cast 550 Spreader Lubrication Requirements

2H. Fast-Cast 550 Service Requirements

Section 3. Fast-Cast 550 Spreader Drawings

Thefollowingpagesshowthedimensions,parts

andspecicationsoftheFast-Cast550Spreader.

Sno-Pro Fast-Cast 550 Spreader

6 of 18

WARNING

IMPORTANT

WARNING

Location

Engine Oil

Take-Up Bearings

4 Bolt Flange Bearings

Spinner Bearings

Conveyor Chain

Lube Type

SAE 30

Bearing Grease

Engine Oil

Location

Engine Oil

Engine Filter

Spark Plugs (.030 Gap)

Harness Connectors

All Bearings

Conveyor Chain

Interval

5 Hours or Daily

50 Hours or 1 Season

100 Hours or 1 Season

50 Hours or Monthly

100 Hours or 1 Season

Recommend

Check

Change

Check or Change

Check Condition

Lubricate

• 5.5 Hp Honda

Vertical Shaft Engine

• 500 lbs. Capacity

• 4 to 24 ft. Spreading

Width

• Stainless Steel Body

• In-Cab Contol Panel

1CS6H

• 5.5 Hp Honda

Vertical Shaft Engine

• 500 lbs. Capacity

• 4 to 24 ft. Spreading

Width

• Carbon Steel Body

• In-Cab Contol Panel

1CS6CPH

• Electric Motor draws

less than 20 amps

• 500 lbs. Capacity

• 4 to 24 ft. Spreading

Width

• Stainless Steel Body

• In-Cab Contol Panel

1CS6CE

Options available for all Fast-Cast 550 Spreaders

• 1WC2 - Weather Cover

• 1CS6-SCR - Top Screen

• 1SM6 - Truck Bed Mount

(trucks only)

Fast-Cast 550 Spreader Models

Sno-Pro Fast-Cast 550 Spreader

7 of 18

40.00

33.38

REAR VIEW

SIDE VIEWREAR VIEW

58.50

23.50

37.00

38.00

1CS6 Fast-Cast 550 Spreader Assembly Overview - Illustrated Parts List

1CS6-P1-00

1CS6-P3-00

1CS6-P3-01

1CS6-P2-03

1CS6-P2-08

1CS5-P2-09

1CS6-P1-11

1CS6-P2-06

1CS6C-P3-00

1CS6C-P3-01

1CS6C-P2-03

1CS6C-P2-08

1CS5C-P2-09

1CS6C-P1-11

1CS6C-P2-06

1CS6P-P1-00

See Page 7

1CS6-P1-12

1CS6-P1-14

Hopper Assembly

Engine Cover

Motorbed Plate

Bumper

Deflector - Fixed

Deflectors

Conveyor Assembly

Gate

Gate Guide

Spinner Cover

Lifting Eye

Item

No.

Qty. Description Part Number

ALUM HOPPER/SS BASE POLY HOPPER/SS BASE POLY HOPPER/CARBON STEEL BASE

FAST-CAST 550 Series

Sno-Pro Fast-Cast 550 Spreader

8 of 18

REAR

VIEW A - A

19 17 12

TOP

A A

Side View

typical of both sides

1CS6 Drive Assembly - Illustrated Parts List

1CS6-P3-375

1CS6-P4-02

1CS6-P4-03

1CS6-P4-04

1CS6-P4-05

1TS17-E11

1CS6-P4-06

1CS6-P4-07

1CS6-P4-08

1CS6-P4-09

1TS17-E10

1CS6-P4-11

1CS6-P4-12

1TS17-E13

1CS6-P4-14

1TS17-E104

1CS6-P4-16

1CS6-P5-03

1CS6-P2-01

3.75 HP Engine

# 40 Spinner Drive Chain

# 40 Clutch Drive Chain

Conveyor Chain

Gear Box

8 T Sprocket 1" Bore

11 T Sprocket 7/8" Bore

16 T Sprocket 1" Bore

52 T Sprocket 3" Bore

24 T Sprocket 3/4" Bore

1" Take Up Bearing

3/4" Pillow Block Bearing

1" Take Up Shaft

4 Bolt Bearing

Conveyor Belt

5/8" Take Up Bolt

Spinner Shaft Nuts

Clutch

Pillow Block Bracket

Item

No.

Qty.

Part

No. Description

Sno-Pro Fast-Cast 550 Spreader

9 of 18

CAB CONNECTIONS

WHITE - CONVEYOR

GREEN - GROUND

BLACK - ENGINE

WHITE - CONVEYOR

1CS6-P5-05-2

26' LONG

1CS6-P5-05-21

4' LONG

INDICATOR LIGHT

REAR VIEW OF

BLACK

GREEN

RED

12VDC BATTERY

OR POWER POINT

BY CUSTOMER

FUSE

WHITE

CONV.

SWITCH

ENG.

SWITCH

CLUTCH

3 WIRE

GREEN

GREEN - GROUND

BLACK - ENGINE

SANDER CONNECTIONS

CONTROL PANEL

1CS6 Fast-Cast 550 Spreader Control Diagram for Gas Motor Powered Spreaders

Sno-Pro Fast-Cast 550 Spreader

10 of 18

1CS6E-M

1CS6E-MP

1CS6E-HWK

1CS6E-SB

1CS6E-SA

1CS6E-H

Electric Motor

Electric Motor Mounting Plate

3/8"-16 x 3/4" Hex Bolt SS

3/8" Flat Washer SS

3/8" Split Lock Washer SS

3/8"-16 Hex Nut SS

11T Drive Sprocket

54T Sprocket

Electrical Harness

Item No.

Qty.Part NumberDescription

1CS6E Electric Drive Assembly - Illustrated Parts List

Spreader

Chassis

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Esparcidor de Sno-Pro

Sno-Pro

Sno-Pro Fast-Cast 2000 (1CS1) Manual de usuario

Manuales populares de Esparcidor de otras marcas

PEQUEA

PEQUEA GT-100 Manual de usuario

Herculano

Herculano H2RS9 Manual de usuario

Epoke

Epoke SKE8 Manual de usuario

GEA

GEA EL44 Hoja de especificaciones

Boss Snowplow

Boss Snowplow TGS 800 Manual de usuario

Fisher

Fisher EMERSON 168 Series Manual de usuario

Fisher

Fisher POLY-CASTER 78601 Manual de usuario

TurfEx

TurfEx RS7200 Manual del propietario

Ferris

Ferris Pathfinder Series Manual de usuario

Fayat Group

Fayat Group DYNAPAC S100 Guía de solución de problemas

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manual de instalación y operación

EASTMAN

EASTMAN CR 500 Manual de usuario

Nogueira

Nogueira RoyalFlow-600 Manual de usuario

Buyers

Buyers TGS05B Manual de usuario

Magnum

Magnum V-BOX PV Series Suplemento

Meyer's

Meyer's VB280 Manual de usuario

SnowEx

SnowEx VX-4210 Manual de usuario

Kramer

Kramer VM-400HDCP Manual de usuario