Snap-On V3300 Manual de usuario
WIRELESS V3300 and 770XD
CAMERA ALIGNER
Quick Start EEWA552B/H and EEWA752B/H Models
ZEEWA552B Rev B
All information contained or disclosed in this document is
considered condential and proprietary by Snap-on. All
manufacturing, use, reproduction, and sales rights are
reserved by Snap-on and the information contained herein
shall not be used in whole or in part without the express
written consent of Snap-on.
Table of Contents
SAFETY INFORMATION ......................................................................................................................... 1
SAFETY INSTRUCTIONS ....................................................................................................................... 2
APPLY SYSTEM POWER........................................................................................................................ 4
SHUTTING DOWN THE COMPUTER..................................................................................................... 4
SYSTEM MAIN MENU............................................................................................................................. 5
PORTABILITY.......................................................................................................................................... 6
PREPARING FOR RELOCATION ........................................................................................................... 6
1
SAFETY INFORMATION
For your safety, read this manual thoroughly before operating the equipment.
The Aligner is intended for use by properly trained skilled automotive technicians. The safety messages
presented in this section and throughout the manual are reminders to the operator to exercise extreme
care when performing wheel alignments with this product.
There are many variations in procedures, techniques, tools, and parts for servicing vehicles, as well as
the skill of the individual doing the work. Because of the vast number of vehicle applications and potential
uses of the product, the manufacturer cannot possibly anticipate or provide advice or safety messages to
cover every situation. It is the automotive technician’s responsibility to be knowledgeable of the vehicle to
be aligned. It is essential to use proper service methods and perform wheel alignments in an appropriate
and acceptable manner that does not endanger your safety, the safety of others in the work area or the
equipment or vehicle being serviced.
It is assumed that, prior to using the Aligner, the operator has a thorough understanding of the vehicle
systems being serviced. In addition, it is assumed he has a thorough knowledge of the operation and
safety features of the alignment rack or lift, and has the proper hand and power tools necessary to per-
form wheel alignments.
When using your garage equipment, basic safety precautions should always be followed, including:
1. Read all instructions.
2. Care must be taken as burns can occur from touching hot parts.
3. The socket-outlet (wall outlet) shall be located near the equipment and shall be easily accessible.
4. Do not operate power tools or equipment with a damaged power cord or if the equipment has been
dropped or damaged until it has been examined by a qualied serviceman.
5. Do not let cord hang over edge of table, bench or counter or come in contact with hot manifolds or
moving fan blades.
6. If an extension cord is necessary, a cord with a current rating equal to or more than that of the equip-
ment should be used. Cords rated for less than the equipment may overheat. Care should be taken
to arrange the cord so that it will not be tripped over or pulled.
7. Always unplug equipment from electrical outlet when not in use. Never use the cord to pull the plug
from the outlet. Grasp plug and pull to disconnect.
8. Let equipment cool completely before putting away. Loop cord loosely around equipment when
storing.
9. To reduce the risk of re, do not operate equipment in the vicinity of open containers of ammable
liquids, such as gasoline.
10. Adequate ventilation should be provided when working on operating internal combustion engines.
11. Keep hair, loose clothing, ngers, and all parts of body away from moving parts.
12. To reduce the risk of electrical shock, do not use on wet surfaces or expose to rain.
13. Use only as described in this manual. Use only manufacturer’s recommended attachments.
14. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses only have impact resistant lenses, they
are NOT safety glasses.
15. Know and understand the proper operating procedures for all power tools used.
16. Caution: Risk of explosion if any battery is replaced by an incorrect type. Dispose of used batteries
according to local and state government regulations.
IMPORTANT!! SAVE THESE INSTRUCTIONS
DO NOT DISCARD!!
2
Risk of electrical shock.
• Do not operate equipment with a damaged power cord or if the equipment
has been dropped or damaged, until it has been examined by a qualied
service person.
• If an extension cord is necessary, a cord with a current rating equal to or
greater than that of the equipment should be used. Cords rated for less
current than the equipment can overheat.
• Unplug equipment from electrical outlet when not in use. Never use the
cord to pull the plug from the outlet. Grasp plug and pull to disconnect.
• Do not expose the equipment to rain. Do not use on wet surfaces.
• Plug unit into correct power supply.
• Do not remove or bypass grounding pin.
Contact with high voltages can cause death or serious injury.
Risk of electrical shock. High voltages are present within the console unit.
• There are no user serviceable items within the console other than the key-
board and printer.
• Service on the unit must be performed by qualied personnel.
• Do not open any part of the console other than noted areas.
• Turn power switch off and unplug the unit before servicing.
Contact with high voltages can cause death or serious injury.
Risk of eye injury. Debris, dirt, and uids may drop from vehicles.
• Knock off any loose debris. Clean surfaces as needed to avoid any materi-
als from falling.
• Wear approved safety glasses when servicing.
Debris, dirt, and uids can cause serious eye injury.
Risk of crushing. Vehicles may roll off alignment lift if not secured.
• Leave automatic transmission in park or manual transmission in gear un-
less equipment operation steps require vehicle in neutral.
• Apply parking brake unless equipment operation steps require wheel
movement.
• Use wheel chocks whenever vehicle is positioned on the lift.
• Follow rack or lift manufacturer’s safety recommendations when lifting a
vehicle.
Vehicles rolling off lifts can cause death or serious injury.
SAFETY INSTRUCTIONS
IMPORTANT!! SAVE THESE INSTRUCTIONS
3
Risk of entanglement or crushing. There are moving parts on vehicle lifts during op-
eration.
• Keep all persons clear of lifts.
• Read lift manufacturer’s operation instructions carefully.
• Follow lift manufacturer’s safety recommendations.
Contact with moving parts could cause injury.
Risk of pinching or crushing body parts when jacking vehicles.
• Keep hands and other body parts away from jacking surfaces.
• Do not use unapproved adapters (i.e. wooden blocks) when jacking a ve-
hicle.
• Do not bypass any jack manufacturer’s safety features.
• Read jack manufacturer’s operation instructions carefully.
• Follow jack manufacturer’s safety recommendations.
Improperly used or maintained jacks can cause injury.
Risk of burns.
• Do not touch hot exhaust systems, manifolds, engines, radiators, etc.
• Wear gloves whenever performing a service near hot components.
Hot components can cause burns.
Risk Of Explosion.
• This equipment has arcing or sparking parts which should not be exposed
to ammable vapors.
• This equipment should be located at least 460mm/18inches above the oor,
and not in a recessed area.
• Do not operate with the cover of the electrical box removed.
• Do not remove/alter grounding wires.
Risk of pinching when camera beams and/or pods are in motion
• Keep hands and other body parts away from camera beams and/or pods
when they are in motion
Risk of injury. Tools may break or slip if improperly used or maintained.
• Use the correct tool for the task.
• Frequently inspect, clean, and lubricate (if recommended) all tools.
• Follow recommended procedures when performing vehicle services.
Tools that break or slip can cause injury.
4
APPLY SYSTEM POWER
1. Ensure that a properly grounded outlet is used. Failure to use proper voltage can and will result in a system
failure.
2. The main power switch is located on the front inside of the Console. Open the front door of the cabinet. Look
at the upper left inside and locate the green toggle switch. With power connected the switch will illuminate.
3. When the power switch is turned on, the unit initiates the camera boot-up. The Home screen will appear
next as the software nishes loading.
This boot sequence will take a few moments. If any problems are encountered during the Power On boot-up
sequence, consult the service representative in your area. The unit may become unresponsive in the event of
a severe power uctuation such as Electrical Fast Transients or Electrostatic Discharge. To restore the unit to
operating condition, turn off all power switches, wait 10 seconds, and turn them back on. If the unit is still unre-
sponsive contact a qualied service technician for repairs.
IMPORTANT NOTE:
SHUTTING DOWN THE COMPUTER
To avoid damaging important les It is necessary to shut down properly before turning off
or restarting the aligner or the computer.
Use the following steps to shut down the aligner from within the Alignment software:
1. Return to the Home Alignment screen.
2. Open the front console door and toggle the power button to the “OFF” position.
3. The computer will automatically shutdown.
5
SYSTEM MAIN MENU
All system usage resides from the Home Screen screen. Each function of the aligner will be followed with screen
prompts. The user needs to simply click a command and the aligner will easily prompt the user to the next step.
No guessing required as the system has been designed with each user in mind.
• Start Alignment - Begin an alignment process
• Vehicle Selection -
• Measure - Select to measure a variety of diagnostic angles
• Adjust - Use this menu to make adjustments determined to be out of spec
• Information
• Preferences - A menu to setup the aligner for desired user interaction
• Service - Choose to access the local or network server, access the Calibration sub menu, several diagnos-
tic screens
• Simulator
• Drive on Camera
NOTE: THE “MENU” PULL OUT TAB IS AVAILABLE ON MOST PAGES TO ALLOW YOU ACCESS OF IM-
PORTANT SCREENS REGARDLESS WHERE YOU ARE IN THE ALIGNMENT PROCESS.
6
PORTABILITY
The Aligner was designed with multiple bay capability. With it’s uniquie Camera Foldup system an Operator
can simply fold up the Camera Arms, unlock the smooth mobility wheels and roll the system to a different bay to
perform fast and accurate alignments. Before moving the system to a different bay please follow the simple steps
listed below before moving the system.
Mobility Mode Alignment Mode
PREPARING FOR RELOCATION
Before moving the alignment system it is recommended that the camera arms be in their lowest most position.
1. From the Home screen select “Service”.
CAUTION!
NEVER RELOCATE THE ALIGNER WITH THE CAMERA
ARMS FOLDED OUT IN THE ALIGNMENT MODE.
NEVER MOVE THE SYSTEM USING THE CAMERA ARMS
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Otro de Snap-On
Snap-On
Snap-On ETHOS+ Manual de usuario
Snap-On
Snap-On SOLUS Ultra Manual de usuario
Snap-On
Snap-On APOLLO D8 Manual de usuario
Snap-On
Snap-On Modis Ultra Manual de usuario
Snap-On
Snap-On Vantage Ultra Manual de usuario
Snap-On
Snap-On VERUS Manual de usuario
Snap-On
Snap-On SOLUS Ultra Manual de usuario
Snap-On
Snap-On Solus Manual de usuario
