SMS DBRF 15-01 Manual de usuario
Installation Manual for W200 and DBRF15-01
Modified date: 22/08/2011
Document Version 2.1
St. Michael Strategies
#201 701 Salaberry
Chambly Québec
Canada J3L 1R2
(450) 658-5148
www.storetraffic.com
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 2
Wireless Sensors (DBRF 15-01) STC-W200 - Traffic Counter
Note: Sensors must be installed so that the beam is at 54 inches from the ground.
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 3
Step 1 Connecting the STC-W200
There are three options to choose when connecting the STC-W200; 1) a computer,
cash register system, point of sales system (POS); 2) a network; or 3) a modem.
If you are an installer, check the Scope of Work to determine the connectivity to
use. The method chosen by the customer will determine the method of
connectivity. If you are uncertain contact SMS for more information. You will collect
the traffic data either at the store level into the router, HUB, POS or a computer.
Connecting:
a) A computer or POS using the provided serial cable. Connect it to the
console port on the STC.
b) A network, using a Ethernet cable from the STC’s Ethernet port to a
hub/switch/router. Verify that the LAN light is ON.
c) A modem using a 9 to 25 pin cable provided. Connect the 9 pin side to the
console port of the STC.
Connect the power adapter from the STC’s power to an outlet in the wall.
Connect the antenna to the antenna port. Make sure it is screwed correctly and
standing at a 90 degree angle as shown on the W200 picture on page 1.
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 4
Step 2: How to remove the sensor from its holster.
Both the receiver and the transmitter come with a holder or holster. To remove the
actual unit from the holster you need to use a pen or another small tool and press
through the opening at the bottom. While doing so, hold each side of the sensor
and just pull the sensor out of his holder.
There is a small switch on the back of the sensor, next to the battery. Initially,
the switch is in the middle position which indicates the sensor is off. Moving
the switch to the right or left will turn the sensor on, in side or front-firing
position. Refer to the next step for more information.
Use Pen to press on
the release button
Pull
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 5
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 6
Step 3: Setting the Sensors to Front or Side Firing
(dia. 1) (dia.2)
(dia.3) (dia.4)
Identify front or side firing configuration
Sensors can be configured to be either front or side firing. This is important and
allows you the flexibility to install the sensors. If you need to align the sensors so
they face each other, this is front firing, and front firing is usual if installed on the
inside of a door frame (dia.1) (dia.3) (dia.5) (dia.6) or side firing if placed on
outside of the door frame (dia,2) (dia.4) (dia.7) (dia.8).
Front firing beam
Side firing beam
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 7
Each set of sensors consists of a receiver and a transmitter. The receiver is the
one with the LCD screen, which register the counts and communicates with the
STC. The transmitter is the one projecting the Infra-red beam.
dia.5 dia.6
dia. 7 dia. 8
As seen in the pictures above, the sensors can be installed in front firing or side
firing configuration. A switch in the back of each sensor (allows it to be configured
accordingly. When changing the firing configuration please move the switch gently
to the middle, and then move it in the desired direction. Both switches must be set
to either front or side firing position to be on. If the switch is left in the middle, the
sensors are off and are not operating.
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 8
(dia. 9)
In a side firing configuration, the receiver’s LCD screen must not be pointing in the
direction of the other sensor. The transmitter has a rectangular cutout in the
transmitter. This side needs to be pointing in the direction of the receiver. Please
refer to the following drawing.
Front firing
Side firing
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 9
Wireless equipment is sensitive to strong interference sources such as a breaker
box, transformers, computer screen. Please install the STC as far away from these
sources as possible.
Installation Manual for W200 and DBRF15-01
SMS Version 2.1 10
Step 4: Configuring the Wireless sensors.
Before Installing the sensors to the door frame, bring them to the STC. Having the
sensors and the STC together allows you to configure the sensors and the STC so
that they communicate with each other. The sensors need to identify themselves
with a signature to the STC. The STC will recognize and register the serial number
of the sensors automatically.
1. On the STC there are 4 arrows: up, down, left and right arrows. Press the
down arrow until you find “Setup”. Press “Enter”.
2. The STC will ask you for a password. The default password is 1,2,3,4.
You can use the up or down arrow to toggle through the numbers, then
press “Enter” to switch to the next. Press “Enter” when the 4th number is
entered.
3. In the setup menu, use the down/up arrow until you get to “Wireless…”
then press “Enter”.
4. You should now see “Wi. Ser.No.”, press “Enter”.
5. You should see “01 – Not Prog” on the screen. Press “Enter”. The screen
will switch to “01 – Scanning”.
6. On the receiver (sensor), press on the button below the LED once for
less than 1 second. The STC should emit a beep.
<Wireless>
01IrR : Scanning
Wireless :
- Wi. Ser.No.
Setup Menu :
- Wireless…
Enter Password :
1234
Main Menu :
- Setup…
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
