SMITH SYSTEM 58040 Manual de usuario
Document #: 179720 Revised: 2/2022
Assembly Instructions
MOTUM MOBILE LECTERN
MODEL NUMBERS
58040 and 58041
Document #: 179720 Revised: 2/2022
Document #: 179720 Revised: 2/2022
Hardware And Components
ITEM NO. PART NO. DESCRIPTION QTY
1 P14310 MWS TD LOCK ASSEMBLY 1
2 P14304 MOBILE LECTERN TO U ASSEMBLY 1
3 P14295 MSW LEG ASSEMBLY LEFT 1
4 P14296 MSW LEG ASSEMBLY RIGHT 1
5 P14314 MOBILE LECTERN DOOR HINGE ASSEMBLY 1
6 P14307 MOBILE LECTERN PED TO LEG BRACKET ASSEMBLY 1
8 P14374 MWS TD TILT SUPPORT ASSEMBLY 1
9 P14510 MWS TD PUSH TO OPEN ROLLER LATCH 1
10 P14319 BUTTERFLY PLATE WITH FOAM MOUNTING TAPE 1
11 P14319 SIT STAND COLUMN WITH TILT 1
12 60085 3” LOCKING CASTER 4
13 67125 12” PENCIL PAPER RETAINER 1
Document #: 179720 Revised: 2/2022
Hardware And Components
Item No.
Part No.
Description
QTY
1
P14322
NO. 10 X 5/8” TORX BUTTON HEAD SCREW
60
2
P14324
NO. 10 X ½” TORX SELF DRILLING BUTTON HEAD SCREW
1
3
P14323
10-32 X ½” TORX BUTTON HEAD W/ PATCH
12
4
P13977
M6 X 1.0 X 20MM SOCKET HEAD, HEX DRIVE, BLK OX
3
5
P13994
M6 X 1.0 X 10MM SOCKET HEAD, HEX DRIVE, BLK OX
4
6
P13995
¼” I.D. PLASTIC LOOP CLAMP
2
7
P13981
HEX KEY 5MM SHORT ARM
1
8
P14329
T25 TORX POWER BIT 2”
1
9
P14369
#10 WASHER 1” OD
4
10
P14320
M6 SPLIT LOCK WASHER
4
Document #: 179720 Revised: 2/2022
Panel Guide
58041 –Left Hand Mobile Workstation
58040 –Right Hand Mobile Workstation
Document #: 179720 Revised: 2/2022
General Assembly Guidelines
•Ensure that all components are accounted for and undamaged before assembling
•Follow each step carefully to ensure the proper assembly of this product
•2-person assembly is highly recommended
•Clean the product with a mild cleaner and damp cloth
Tools
•Framing Square
•Drill
•Screwdriver (optional)
•Wood Clamps (optional)
•¼” bit extender (optional)
•#1 and #2 Phillips bit
Document #: 179720 Revised: 2/2022
Assembly Instructions
1. Unpack and confirm all parts are present.
2. There are 2 panels (BB), one will attach to assembly (#3) and the other to (#4). Begin by placing one panel (BB) on
smooth, clean, surface, facedown with pilot holes facing up. Position leg assembly (#3) with holes aligned (as
shown) and attach using 4x fastener [#1]. Before tightening, make sure the top edge of (#3) and panel (BB) are flush
and that the spacing on both sides is uniform, use a spacer if necessary. Repeat steps with assembly (#4).
Document #: 179720 Revised: 2/2022
Assembly Instructions
3. Insert support assembly (#8) into cut-out in panel (X). Using 4x washer [#9] and 4x fastener [#2], loosely finger
tighten (#8) into place. Align latch (#9) with pilot holes on panel (X) and attach using the 2x shorter fasteners
(included in latch packet). (See Detail: C) Next, position panel (X) into assembly (#2) so edges are aligned and spacing
on either side is uniform.
Document #: 179720 Revised: 2/2022
Assembly Instructions
4. Align assemblies (#3) and (#4) to assembly (#2) making sure the back edges are snug and that the flange on bracket
(#2) slides between panel (BB) and corner brackets on (#3) and (#4) (as shown in Detail: A below). Attach assembly
(#2) to 2x panels (BB) using 6x fastener [#1]
Document #: 179720 Revised: 2/2022
Assembly Instructions
5. Use 6x fastener [#1] to attach (#3) and
(#4) to (X) (as shown in Detail: B).
6. For left hand unit –Attach hinge (#5) to (#3) using 2x fastener [#1]. Do not fully tighten.
For right hand unit –Attach hinge (#5) to (#4) using 2x fastener [#1]. Do not fully tighten.
Please note
on
hinge orientation
, the horizontal
slot
should be on
top,
and the vertical slot should
be on bottom when
installing
.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
