Smith & Noble Smart Shades Instrucciones de funcionamiento

OPERATING & PROGRAMMING GUIDE

FOR EURO TRACK BASIC

HEAVY DUTY HARDWARE

Smith & Noble

smart Ishades

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

smithandnoble.com

800.248.8888

SETTINGS MOTOR

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

SETTING ROD LIMITS

OPERATING THE REMOTE

Open and Close Drapes

Select the desired channel with the

CHANNEL buon.

Press the UP or DOWN buons to close

or open the drape(s).

Press the STOP buon to stop the rod at

the desired posion.

Adjust Rod Limits (If Desired)

The open and close limits have been

set at the factory. If you need to make

adjustments to the limits, follow the

instrucons below.

Use the CHANNEL buons to select

the channel for the rod that needs to be

adjusted. Then follow the direcons below.

When adjusng one rod, the other rods

on that channel need to be temporarily

unpaired from the remote (see UNPAIR

THE REMOTE).

Once limits are adjusted, the other rods

will need to be re-paired to the channel

(see PAIR THE REMOTE).

If there is a single rod on the channel,

proceed to SETTING LIMITS.

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

HOW TO

OPERATE MOTORIZED

DRAPES

SCAN TO PLAY VIDEO

HOW TO

CHANGE SET LIMITS

SCAN TO PLAY VIDEO

PAIRING THE REMOTE

Your rod will need to be paired to the

remote prior to operang your rod. See

Pair the Remote below.

Pair The Remote

This remote control has 15 channels.

Before pairing the remote, determine

which rod(s) you want on which channel.

All rods paired to a remote will also

automacally be programmed to the

“ALL” channel which is "0".

It is recommended to only pair one

rod per channel unless it is absolutely

necessary to group rods other than the

"ALL" channel. This simplies adjusng

limits and seng favorites.

If a baery is not already installed in the

remote, follow the instrucons REPLACE

BATTERY IN REMOTE.

1. Select the channel you want to

program your rod/track. Press SETTING

buon on the motor for 2 seconds. Once

you release it, the motor will beep once

and the light on motor will light up green.

2. Press the STOP buon on the remote

for 2 seconds. The motor will sound

3 beeps. The motor has been paired

successfully.

NOTE: If the STOP buon is not pressed

within 10 seconds, the rod will exit the

paring mode automacally.

Repeat steps 1-2 to pair remaining rods

to the rest of the channels.

HOW TO

PAIR REMOTE

TO MOTOR

SCAN TO PLAY VIDEO

smithandnoble.com

800.248.8888

SETTING MOTOR LIMITS

Open Limit

1. Press and hold UP and STOP buons for

5 seconds. The motor will sound a long

beep.

2. Press the UP buon to open the drapes.

3. If the drapes don't open all the way, push

the master carrier all the way to the end

to push the drapery all the way open.

4. Press the STOP buon when the drapes

are at the desired posion.

5. Press and hold the UP and STOP buons

for 2 seconds. The motor will sound 3

beeps.

The new open limit is now set.

Close Limit

1. Press and hold DOWN and STOP buons

for 5 seconds. The motor will sound a

long beep.

2. Press the DOWN buon to close the

drapes.

3. If the drapes don't close all the way, push

both master carriers towards the middle

unl the drapes are closed all the way.

4. Press the STOP buon when the drapes

are at the desired posion.

5. Press and hold the DOWN and STOP

buons for 2 seconds. The motor will

sound 3 beeps.

The new close limit is now set.

NOTE: When seng new limits, your

previously programmed Favorite Posion

will not be deleted.

CR2450

LITHIUM BATTERY

REMOTE BACK

BUTTON

SETTING & USING A FAVORITE POSITION

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

If there is only a single rod on the channel proceed

to SETTING A FAVORITE POSITION below.

If there is more than one rod on the channel,

before seng a favorite posion, all rods on

that channel will need to be unpaired from the

remote (see UNPAIR THE REMOTE). Next, pair

only the rod that needs a favorite posion set

(see PAIR THE REMOTE). Then follow the steps

below to set a favorite posion.

Seng a Favorite Posion

Check both upper and lower limits are set.

Use the UP or DOWN buons to posion the

rod/drape at the desired “favorite” posion.

Press P2 on the back of the remote unl the

motor beeps.

Press the STOP buon unl the motor beeps

once then release.

Press the STOP buon again and the motor will

sound 3 beeps. Your “favorite” posion is now set.

Using a Favorite Posion

Press the STOP/FAVORITE buon for 2

seconds. The rod will automacally move to the

set “favorite” posion.

Removing a Favorite Posion

Press the P2 buon on the back of the remote

unl the motor beeps.

Press the STOP buon unl the motor beeps

then release.

Press the STOP buon again and the motor will

sound a long beep. Your “favorite” posion has

now been removed.

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

HOW TO

SET YOUR FAVORITE

POSITION

SCAN TO PLAY VIDEO

smithandnoble.com

800.248.8888

SETTINGS MOTOR

CHANNEL

DISPLAY

STOP/

FAVORITES

DOWN

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

UNPAIR THE REMOTE

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

Adding a remote

Start with a remote that is already paired to

the rod and select the channel programmed to

that rod.

Press P2 on the paired remote once, the motor

will beep once.

Press P2 on the paired remote once again, the

motor will beep once.

Press P2 on the new remote once, the motor

will beep 3 mes. The new remote is now

paired to the rod.

Removing a remote

Remote (a) and remote (b) are both paired to

the rod and you want to remove remote (b).

Press P2 on the remote (a) once, the motor will

beep once.

Press P2 on the remote (a) once again, the

motor will beep once.

Press P2 on the remote (b) once, the motor will

beep 3 mes. Remote (b) is no longer paired

with the rod.

ADD OR REMOVE REMOTE OR CHANNEL

CR2450

LITHIUM BATTERY

REMOTE BACK

P2 BUTTON

DISABLING UNUSED CHANNELS

1. Press SETTING buon on the motor for

2 seconds. The motor will sound a long beep.

2. Press the STOP buon for 2 seconds. The

motor will sound 3 beeps. The motor has

been unpaired successfully.

NOTE: If the STOP buon is not pressed within

10 seconds, the motor will exit the unparing

mode automacally.

The 15 channel remote has the opon of

turning o unused channels, making channel

selecon easier.

Press and hold both Channel UP and Channel

DOWN buons unl the LED screen displays

the number 15.

Scroll through the channels to select the

required number of channels (between 1-15).

Press the STOP buon once to conrm

selecon. The remote will now only display the

number of channels selected.

Follow the same process if you need to re-add

channels.

smithandnoble.com 800.248.8888

RESETTING TO FACTORY MODE

Reset to Factory Mode:

Press and hold SETTING bu on on the

motor for 14 seconds and the motor light

will light up 3  mes.

Release bu on and the motor beeps 3

 mes. The motor has been reset to factory

mode. All se ngs have been cleared.

NOTE: Once in factory mode, the motor will

go to sleep. The motor must be taken out

of sleep mode to operate and reset limits.

Press the SETTING bu on on the motor for

2 seconds to wake up. Once the motor

is out of sleep mode, it can be paired to

controller and limits can be set.

CR2450

LITHIUM BATTERY

REMOTE BACK

P2 BUTTON

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

SWITCHING DIRECTION

Switching Direc on (Polarity)

If the drape opens when pressing the

DOWN bu on and closes when pressing

the UP bu on, the direc on needs to be

switched.

Select the channel your motorized track is

on. Press and hold the se ngs bu on un l

the green light on motor lights up three

 mes, approximately 10 seconds. Release

the bu on and the motor will beep three

 mes. Press the DOWN bu on and motor

will beep 3  mes. The direc on has been

switched successfully.

HOW TO

SWITCH

DIRECTION

SCAN TO PLAY VIDEO

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

BOTTOM OF BATTERY

SETTINGS

MOTOR

10 11

smithandnoble.com 800.248.8888

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

BATTERY

INSET

BACK OF

REMOTE

BACK OF

REMOTE

ADJUSTING SPEED REPLACE BATTERY IN REMOTE

Slide the back cover o the remote.

Remove the ba ery and replace it with a

new ba ery (CR2450). The new ba ery

should be inserted with the wri ng facing

up (posi ve side up).

Replace the back cover of the remote.

NOTE: When installing the ba ery for

the  rst  me, you will need to remove the

 lm packing sheet.

CR2450

LITHIUM BATTERY

REMOTE BACK

P2 BUTTON

CHANNEL

DISPLAY

OPEN

STOP/

FAVORITES

CHANNEL UP

CHANNEL DOWN

REMOTE FRONT

Adjus ng the Speed

ACCELERATION:

Select the channel your motorized track

is on. Press P2 bu on on the back of the

remote un l the motor beeps once.

Press the UP bu on un l the motor

beeps once.

Press the UP bu on again un l the

motor beeps once. The rod speed is now

accelerated.

HOW TO

SPEED UP THE

MOTOR

SCAN TO PLAY VIDEO

DECELERATION:

Select the channel your motorized track

is on. Press P2 bu on on the back of the

remote un l the motor and beeps once.

Press the DOWN bu on un l the motor

beeps once.

Press the DOWN bu on again un l the

motor beeps once. The rod speed is now

decelerated.

HOW TO

SLOW DOWN THE

MOTOR

SCAN TO PLAY VIDEO

REMOVING THE REMOTE BACK COVER

For added safety, the remote has a locking

tab on the back cover to prevent accidental

removal.

To remove the back cover, press the tab down

gently using a small screwdriver. While the tab

is depressed, slide the cover down then li the

cover up to remove from the remote.

If the back cover does not have a locking tab,

simply slide the cover down to unlock then li

the cover up to remove from the remote.

COVER

SLIDES OFF

CR2450

LITHIUM BATTERY

CR2450

LITHIUM BATTERY

TAB

12 smithandnoble.com

800.248.8888

TROUBLESHOOTINGSHORTCUTS

SETTINGS STEPS

Pairing SETTING Buon on motor for 2 seconds (1 beep) →

STOP for 2 seconds (3 beeps)

Switch Rotang

Direcon

SETTING Buon on motor for 10 seconds (Green light lights

up 3 mes) → Release SETTING Buon motor (3 beeps) →

DOWN buon motor (3 beeps)

Seng Closed Limit DOWN + STOP 5 seconds (1 beep) → adjust limit →

DOWN + STOP 2 seconds (3 beeps)

Seng Open Limit UP + STOP 5 seconds (1 beep) → adjust limit →

UP + STOP 2 seconds (3 beeps)

Add / Remove Favorite

Posion

P2 for 2 seconds (1 beep) → STOP (1 beep) →

STOP (3 beeps)

Add or Remove

Addional Remote

Press P2 on paired remote once (1 beep) →

Press P2 on paired remote once again (1 beep) →

Press P2 on new remote once (3 beeps)

Adjust Speed -

Acceleraon P2 (1 beep) → UP (1 beep) → UP (1 beep)

Adjust Speed -

Deceleraon P2 (1 beep) → DOWN (1 beep) → DOWN (1 beep)

PROBLEM SOLUTION

My drapes go beyond the rod. Your limit has not been set properly.

Repeat seng your closed limits.

My drapes don't open all the way.

1. Try to reset the open limits again.

2. Make sure the motor power cord has

been tucked away at the back of motor

with Velcro so it won't interfere with

drapes closing.

The motor does not work.

1. Check that the power source and motor

are connected properly.

2. Make sure the antenna cord is intact.

The indicator light on the remote does

not shine or the remote controlling range

becomes shorter.

Replace the baery in the remote.

For more trouble shoong help, call us at 800.248.8888

or visit us online at smithandnoble.com to connect with a live chat assistant,

6am - 6pm Monday - Friday PT, 7am-4pm Saturday & Sunday PT

14 smithandnoble.com

NOTES

800.248.8888

NOTES

Warranty Service

The enjoyment of your window coverings should be everlasting, which is why

our products come with a limited lifetime warranty. The warranty applies to the

original owner, requires a proof of purchase (hang on to your receipt!) and

covers defects in material or craftsmanship. Blinds or blinds must have been

properly installed. We reserve the right to determine if your window covering

warrants a repair or a replacement. Visit smithandnoble.com/guarantee to see

full details. In need of warranty service? Call us at 800.248.8888 and we’ll

arrange for a repair or replacement ASAP.

Otros manuales para Smart Shades

Tabla de contenidos

Otros manuales de Mando a distancia de Smith & Noble

Smith & Noble

Smith & Noble Motivia Manual de usuario

Smith & Noble

Smith & Noble Motivia Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación